Manuals / Lenovo / Computer Equipment / Server

Lenovo RS210 manual Installing the riser-card assembly

Models: RS210

1 244

Download 244 pages 35.96 Kb

Page 166

Installing the riser-card assembly

6.If the riser-card assembly is an optional PCI-X riser-card assembly, disconnect the riser-card power cable 1 from the riser-card assembly.

7.Disconnect any cables from the PCI cards in the riser-card assembly.

8.If you are instructed to return the riser-card assembly, follow all packaging instructions, and use any packaging materials for shipping that are supplied to you.

Installing the riser-card assembly

To remove the riser-card assembly, complete the following steps:

The server comes with one riser-card assembly that contains two PCI Express connectors.

To install the riser-card assembly, complete the following steps:

1.Read the safety information in “Important Safety Information” on page 1 and “Guidelines for trained service technicians” on page 115.

2.Install the PCI cards in the riser-card assembly.

3.Reconnect any PCI card cables that you disconnected when you removed the riser-card assembly.

4.If the riser-card assembly is an optional PCI-X riser-card assembly, reconnect the riser-card power cable 1 to the riser-card assembly.

158ThinkServer ThinkServer RS210, Types 6531, 6532, 6533, and 6534: Hardware Maintenance Manual

Image 166

Lenovo RS210 manual Installing the riser-card assembly

Contents

Hardware Maintenance Manual ThinkServer RS210Machine Types 6531, 6532, 6533, and Page Hardware Maintenance Manual ThinkServer ThinkServer RS210, Types 6531, 6532, 6533, andSecond Edition January Copyright Lenovo Portions Copyright International Business Machines Corporation 2007Chapter 1. About this manual ContentsChapter 4. Diagnostics Chapter 2. General informationChapter 5. Locating Server Controls and connectors Chapter 6. Replacing FRUsChapter 8. Configuring the server Chapter 7. Parts listing, RS210 Types 6531, 6532, 6533, andContents Appendix. Notices IndexImportant Safety Information Chapter 1. About this manualSafety statements Statement DANGER To avoid a shock hazardDo not Dispose of the battery as required by local ordinances or regulationsStatement v Throw or immerse into water v Heat to more than 100C 212FAppareil A Laser de Classe DANGERClass 1 Laser Product Laser Klasse Laser Klass Luokan 1 Laserlaite ` Statement≥ 18 kg 39.7 lb Use safe practices when lifting StatementStatement ≥ 32 kg 70.5 lbStatement Important information about replacing RoHS compliant FRUsDo not place any object on top of rack-mounted devices StatementTurkish statement of compliance Türkiye EEE Yönetmeliğine Uygunluk Beyanıv UEFI-compliant server firmware Features and technologiesChapter 2. General information v Dual-core or quad-core processingv Integrated Trust Platform Module v Preboot diagnostics programv Integrated network support v Large data-storage capacity and hot-swap capabilityv EasyStartup DVD Specificationsv EasyManage DVD Table 1. Features and specifications continued SoftwareEasyStartup Lenovo provides software to help get your server up and runningEasyManage Page About the checkout procedure Checkout procedureChapter 3. General Checkout 3. Follow the problem-resolution procedures Performing the checkout procedureDiagnosing a problem 1. Determine what has changed1 Make sure that all installed hardware and software are supported a. Check for and apply code updatesb. Check for and correct an incorrect configuration c. Check for service bulletinsd. Check for and replace defective hardware Undocumented problems2 From the Select your product list, select Servers and Storage 4 Under Support & downloads, click Troubleshootv POST error messages and error logs Chapter 4. DiagnosticsDiagnostic tools v Troubleshooting tablesViewing event logs through the Setup utility Viewing event logs without restarting the serverClearing the event logs POST error codesPOST Description Error codeAction Description Error codeAction Description Error codeAction Error code Description Error codeAction Description Error codeAction Action Error codeDescription 2. Select System Event LogSystem-event log InformationIntegrated management module error messages The Processor CPU nStatus has Page Sensor CPU nOverTemp has Page The System %1 encountered a POST Page Sensor Sys Board Fault has Page Memory Logging Limit Reached for Page A PCI SERR has occurred on system Page New Key and Certificate xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx Attempting to %1 server %2 by userxxx.xxx.xxx.xxx xxx.xxx.xxx.xxx Watchdog %1 Failed to Capture Page Error Troubleshooting tables EasyStartup problemsDVD drive problems trained service technician General problemsHard disk drive problems problem has occurredSymptom Hypervisor problems System Settings -- Integrated Management Module -- POST Watchdog Intermittent problemsSymptom ActionKeyboard, mouse, or pointing-device problems Memory problems Microprocessor problems Monitor problems Page Optional-device problems Power problems Serial-device problems Software problems Error LEDs Universal Serial Bus USB port problemsVideo problems New graphic to be added in the next draft3. Remove the server cover and look inside the server for lit LEDs. Certain components inside the server have LEDs that will be lit to indicate the location of a problem. For example, a DIMM error will light the LED next to the failing DIMM on the system board Power-supply LEDs System pulse LEDsDiagnostic programs and messages Table 4. System pulse LEDsDiagnostic text messages Running the diagnostic programsViewing the test log Diagnostic messages Table 5. DSA Preboot messagesTable 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Recovering the server firmware In-band manual recovery methodIn-band automated boot recovery method Solving power problems Automated boot recovery ABRThree boot failure Solving Ethernet controller problemsSolving undetermined problems Problem determination tips Chapter 5. Locating Server Controls and connectors Front viewRear view System-board internal connectors Chapter 5. Locating Server Controls and connectorsSystem-board external connectors System-board optional-device connectors Page System-board switches and jumpers System-board LEDs Table 7. System-board LEDsTurning on the server Server power featuresTurning off the server Statement The server can be turned off in any of the following waysInspecting for unsafe conditions Guidelines for trained service techniciansChapter 6. Replacing FRUs Guidelines for servicing electrical equipmentWorking inside the server with the power on Handling static-sensitive devices Major components of the server Installing the cover Removing and installing the coverRemoving the cover Removing and installing the bezel Installing the DIMM air baffle Removing and installing the DIMM air baffleRemoving the DIMM air baffle Replacing a memory module DIMM Supported memory typesUnbuffered DIMMs UDIMMs Registered DIMMs RDIMMsTable 11. Supported RDIMM population per channel Removing a memory moduleTable 13. RDIMM population rule for dual-channel symmetric mode Installing a memory module Replacing hard disk drives Removing a simple-swap Serial ATA SATA hard disk driveInstalling a simple-swap Serial ATA SATA hard disk drive Removing a hot-swap hard disk drive Installing a hot-swap hard disk drive Replacing a PCI card Removing a PCI card8. Place the riser-card assembly on a flat, static-protective surface Installing a PCI card Replacing a USB embedded hypervisor flash device Removing a USB embedded hypervisor flash deviceReplacing the operator information panel assembly Installing a USB embedded hypervisor flash deviceRemoving the operator information panel assembly Installing the operator information panel assembly Replacing the drive cage Removing the drive cageTo remove a drive cage, complete the following steps Installing the drive cage Replacing the microprocessor and heat sink Removing the microprocessor Installing the microprocessor Heatsink Orientation DIMMs DIMMsThermal grease Replacing the system board Removing the system boardInstalling the system board Replacing the power supply StatementRemoving the power supply StatementInstalling the power supply Replacing a fan assembly Removing a fan assemblyInstalling a fan assembly Replacing the system-board battery Removing the batteryStatement Installing the batteryMicroprocessor Do not Dispose of the battery as required by local ordinances or regulationsTo install the replacement battery, complete the following steps v Throw or immerse into water v Heat to more than 100C 212FReplacing the SAS/SATA hard disk drive back plate or backplane Installing the backplane or back plate 3.5-inch drivesRemoving the backplane or back plate 3.5-inch drives 1 Connectors 2 Guide channels 4 Connectors Removing the SAS backplane 2.5-inch drives2 Connectors 1 Alignment tabs 3 Alignment slotsReplacing the PCI riser-card assembly Installing the SAS backplane 2.5-inch drivesRemoving the riser-card assembly Installing the riser-card assembly Replacing an IBM ServeRAID-BR10il SAS/SATA Controller Removing an IBM ServeRAID-BR10il SAS/SATA ControllerInstalling an IBM ServeRAID-BR10il SAS/SATA controller 4. Remove the cover see “Removing and installing the cover” on page Replacing the DVD drive cable Removing the DVD drive cableInstalling the DVD drive cable Replacing a DVD drive Removing a DVD driveInstalling a DVD drive Statement DANGERRemoving the virtual media key Installing the virtual media keyReplacing the virtual media key MicroprocessorReplacing the PCI-X riser-card power cable Removing the PCI-X riser-card power cableUpdating the Universal Unique Identifier UUID Installing the PCI-X riser-card power cablec. From Family list, select ThinkServer RS210, and click Continue uuidvalue accessmethodimmpassword imminternalipimmpassword Updating the DMI/SMBIOS dataimmexternalip immuseridaccessmethod m/tmodelassetmethod immpasswordimmpassword Completing the FRU replacementd. Click Downloads and drivers c. From Family list, select ThinkServer RS210, and click ContinueConnecting the cables Updating the server configuration Page Chapter 7. Parts listing, RS210 Types 6531, 6532, 6533, and 3. From Family list, select ThinkServer RS210, and click Continue12 Riser card assemblyPower supply BezelReplaceable server components Table 15. Parts listing, Types45J9646 Table 15. Parts listing, Types 6531 continued45J9658 45J9648Table 15. Parts listing, Types 6531 continued Heat Sink models CTO All Models6531 Software FRU FRU#Table 16. Parts listing, Types 46U2117 Table 16. Parts listing, Types 6532 continued33F8354 Table 16. Parts listing, Types 6532 continued CRU partTable 17. Parts listing, Types Table 17. Parts listing, Types 6533 continued Table 17. Parts listing, Types 6533 continued CRU part46M0864 Table 17. Parts listing, Types 6533 continued46M0922 Table 18. Parts listing, Types Table 18. Parts listing, Types 6534 continued Table 18. Parts listing, Types 6534 continued CRU partTable 18. Parts listing, Types 6534 continued CRU partPower cords Table 20. Power cords, Type Table 19. Power cords, TypeLenovo Power cord part Lenovo Power cord partTable 21. Power cords, Type Table 22. Power cords, Typenumber Table 22. Power cords, Type 6534 continuedLenovo Power cord part Used in these countries and regionsPage v Boot Manager program Chapter 8. Configuring the serverv Setup Utility program v LSI Configuration Utility programSetup Utility menu choices Using the Setup UtilityStarting the Setup Utility v System SettingsPOST Watchdog Timer PowerForce Legacy Video on Boot POST Watchdog Timer ValueAdministrator Password v Boot ManagerPower-on Password v Save Settingsv Restore Settings PasswordsPower-on password v Load Default SettingsResetting passwords Administrator passwordTable 23. System board jumpers Using the Boot Manager program Configuring RAID controllersUsing LSI Configuration Utility program Formatting a hard disk drive Starting the LSI Configuration Utility program3. Select System Settings → Adapters and UEFI drivers Creating a RAID array of hard disk drivesMain menu of the WebBIOS utility Using the WebBIOS utilityStarting the WebBIOS utility Creating a storage configuration using the Configuration WizardNew Configuration Using the EasyStartup DVDClear Configuration Add ConfigurationBefore you use the EasyStartup DVD Setup and configurationEasyStartup overview Configuring RAID Typical operating system installationUpdating the firmware Installing your operating system without using EasyStartup3. From Family list, select ThinkServer RS210, and click Continue Recovering the UEFI firmware Using the EasyUpdate Firmware Updater toolStarting the backup server firmware 3. From Family list, select ThinkServer RS210, and click ContinueTable 25. System board jumpers v Command-line interface IPMI Shell Using the integrated management modulev Serial over LAN Installation requirements IBM Advanced Settings Utility programInstalling ThinkServer EasyManage software Installation orderInstalling Microsoft SNMP services Installing Windows 2008 32-bit componentsInstalling Web Server Role IIS 1. Click Start - Server ManagerEnabling the remote presence feature Uninstalling the LANDesk Software AgentUsing the remote presence capability and blue-screen capture Obtaining the IP address for the IMMLogging on to the Web interface Configuring the Gigabit Ethernet controllersEnabling the Intel Gigabit Ethernet Utility program b. Select System Settings → Devices and I/O Ports Enabling and configuring Serial over LAN SOLUEFI update and configuration v Remote Console Enable v Serial Port Sharing EnableLenovo United States, Inc 1009 Think Place - Building One Appendix. NoticesMorrisville, NC U.S.A Attention Lenovo Director of Licensing Trademarks Important notesProduct recycling and disposal Appendix. NoticesTürkiye EEE Yönetmeliğine Uygunluk Beyanı Recycling statements for JapanEEE Yönetmeliğine Uygundur Battery return program For the European UnionFederal Communications Commission FCC statement German Ordinance for Work gloss statementElectronic emission notices Industry Canada Class A emission compliance statementGermany Class A compliance statement United Kingdom telecommunications safety requirementEuropean Union EMC Directive conformance statement Notice to CustomersJapan Voluntary Control Council for Interference VCCI statement Taiwan Class A warning statementKorea Class A warning statement People’s Republic of China Class A warning statementAppendix. Notices Page Index A Page removing continued PCI card continuedserver continued Page Page Part Number Printed in USA 1P P/N