Manuals / Lenovo / Computer Equipment / Server

Lenovo RS210 manual 1 Connectors 2 Guide channels

Models: RS210

1 244

Download 244 pages 35.96 Kb

Page 163

1 Connectors

Note: The following illustration shows installing the hot-swap SAS/SATA backplane.

1 Connectors

2 Guide channels

1.Connect the power cable to the replacement backplane or back plate.

2.Reconnect the backplane or back plate cables:

vIf the server is a hot-swap model, reconnect the SAS/SATA controller signal cable to the backplane.

vIf the server is a simple-swap model that contains a standard SATA back plate, reconnect the SATA cable to the system board. See “System-board internal connectors” on page 107 for the location of the SATA connectors on the system board.

Note: Make sure that the cable drive number on the back plate matches the SATA connector number on the system board.

vIf the server is a simple-swap model that contains a SATA RAID back plate, reconnect the SAS signal cable to the SAS/SATA controller.

3.Slide the backplane or back plate into the card guides, making sure that any nearby wires or cables are not trapped or pinched.

4.Press firmly until the backplane or back plate is fully seated.

5.Install the hard disk drives.

6.Go to “Completing the FRU replacement” on page 173.

Chapter 6. Replacing FRUs 155

Image 163

Lenovo RS210 manual 1 Connectors 2 Guide channels

Contents

Hardware Maintenance Manual ThinkServer RS210Machine Types 6531, 6532, 6533, and Page ThinkServer ThinkServer RS210, Types 6531, 6532, 6533, and Hardware Maintenance ManualPortions Copyright International Business Machines Corporation 2007 Second Edition January Copyright LenovoChapter 2. General information ContentsChapter 4. Diagnostics Chapter 1. About this manualChapter 6. Replacing FRUs Chapter 5. Locating Server Controls and connectorsChapter 8. Configuring the server Chapter 7. Parts listing, RS210 Types 6531, 6532, 6533, andContents Index Appendix. NoticesChapter 1. About this manual Important Safety InformationSafety statements To avoid a shock hazard Statement DANGERv Throw or immerse into water v Heat to more than 100C 212F Dispose of the battery as required by local ordinances or regulationsStatement Do notStatement DANGERClass 1 Laser Product Laser Klasse Laser Klass Luokan 1 Laserlaite ` Appareil A Laser de Classe≥ 32 kg 70.5 lb Use safe practices when lifting StatementStatement ≥ 18 kg 39.7 lbStatement Important information about replacing RoHS compliant FRUsDo not place any object on top of rack-mounted devices StatementTürkiye EEE Yönetmeliğine Uygunluk Beyanı Turkish statement of compliancev Dual-core or quad-core processing Features and technologiesChapter 2. General information v UEFI-compliant server firmwarev Large data-storage capacity and hot-swap capability v Preboot diagnostics programv Integrated network support v Integrated Trust Platform Modulev EasyStartup DVD Specificationsv EasyManage DVD Lenovo provides software to help get your server up and running SoftwareEasyStartup Table 1. Features and specifications continuedEasyManage Page About the checkout procedure Checkout procedureChapter 3. General Checkout 1. Determine what has changed Performing the checkout procedureDiagnosing a problem 3. Follow the problem-resolution proceduresc. Check for service bulletins a. Check for and apply code updatesb. Check for and correct an incorrect configuration 1 Make sure that all installed hardware and software are supported4 Under Support & downloads, click Troubleshoot Undocumented problems2 From the Select your product list, select Servers and Storage d. Check for and replace defective hardwarev Troubleshooting tables Chapter 4. DiagnosticsDiagnostic tools v POST error messages and error logsViewing event logs without restarting the server Viewing event logs through the Setup utilityClearing the event logs POST error codesPOST Description Error codeAction Description Error codeAction Description Error codeAction Error code Description Error codeAction Description Error codeAction 2. Select System Event Log Error codeDescription ActionInformation System-event logIntegrated management module error messages The Processor CPU nStatus has Page Sensor CPU nOverTemp has Page The System %1 encountered a POST Page Sensor Sys Board Fault has Page Memory Logging Limit Reached for Page A PCI SERR has occurred on system Page New Key and Certificate xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx Attempting to %1 server %2 by userxxx.xxx.xxx.xxx xxx.xxx.xxx.xxx Watchdog %1 Failed to Capture Page Error EasyStartup problems Troubleshooting tablesDVD drive problems problem has occurred General problemsHard disk drive problems trained service technicianSymptom Hypervisor problems Action Intermittent problemsSymptom System Settings -- Integrated Management Module -- POST WatchdogKeyboard, mouse, or pointing-device problems Memory problems Microprocessor problems Monitor problems Page Optional-device problems Power problems Serial-device problems Software problems New graphic to be added in the next draft Universal Serial Bus USB port problemsVideo problems Error LEDs3. Remove the server cover and look inside the server for lit LEDs. Certain components inside the server have LEDs that will be lit to indicate the location of a problem. For example, a DIMM error will light the LED next to the failing DIMM on the system board System pulse LEDs Power-supply LEDsTable 4. System pulse LEDs Diagnostic programs and messagesDiagnostic text messages Running the diagnostic programsViewing the test log Table 5. DSA Preboot messages Diagnostic messagesTable 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued Table 5. DSA Preboot messages continued In-band manual recovery method Recovering the server firmwareIn-band automated boot recovery method Solving Ethernet controller problems Automated boot recovery ABRThree boot failure Solving power problemsSolving undetermined problems Problem determination tips Front view Chapter 5. Locating Server Controls and connectorsRear view Chapter 5. Locating Server Controls and connectors System-board internal connectorsSystem-board external connectors System-board optional-device connectors Page System-board switches and jumpers Table 7. System-board LEDs System-board LEDsTurning on the server Server power featuresTurning off the server The server can be turned off in any of the following ways StatementGuidelines for servicing electrical equipment Guidelines for trained service techniciansChapter 6. Replacing FRUs Inspecting for unsafe conditionsWorking inside the server with the power on Handling static-sensitive devices Major components of the server Installing the cover Removing and installing the coverRemoving the cover Removing and installing the bezel Installing the DIMM air baffle Removing and installing the DIMM air baffleRemoving the DIMM air baffle Supported memory types Replacing a memory module DIMMRegistered DIMMs RDIMMs Unbuffered DIMMs UDIMMsTable 13. RDIMM population rule for dual-channel symmetric mode Removing a memory moduleTable 11. Supported RDIMM population per channel Installing a memory module Removing a simple-swap Serial ATA SATA hard disk drive Replacing hard disk drivesInstalling a simple-swap Serial ATA SATA hard disk drive Removing a hot-swap hard disk drive Installing a hot-swap hard disk drive Removing a PCI card Replacing a PCI card8. Place the riser-card assembly on a flat, static-protective surface Installing a PCI card Removing a USB embedded hypervisor flash device Replacing a USB embedded hypervisor flash deviceReplacing the operator information panel assembly Installing a USB embedded hypervisor flash deviceRemoving the operator information panel assembly Installing the operator information panel assembly Removing the drive cage Replacing the drive cageTo remove a drive cage, complete the following steps Installing the drive cage Replacing the microprocessor and heat sink Removing the microprocessor Installing the microprocessor DIMMs DIMMs Heatsink OrientationThermal grease Removing the system board Replacing the system boardInstalling the system board Statement Replacing the power supplyStatement Removing the power supplyInstalling the power supply Removing a fan assembly Replacing a fan assemblyInstalling a fan assembly Removing the battery Replacing the system-board batteryStatement Installing the batteryMicroprocessor v Throw or immerse into water v Heat to more than 100C 212F Dispose of the battery as required by local ordinances or regulationsTo install the replacement battery, complete the following steps Do notReplacing the SAS/SATA hard disk drive back plate or backplane Installing the backplane or back plate 3.5-inch drivesRemoving the backplane or back plate 3.5-inch drives 1 Connectors 2 Guide channels 1 Alignment tabs 3 Alignment slots Removing the SAS backplane 2.5-inch drives2 Connectors 4 ConnectorsReplacing the PCI riser-card assembly Installing the SAS backplane 2.5-inch drivesRemoving the riser-card assembly Installing the riser-card assembly Removing an IBM ServeRAID-BR10il SAS/SATA Controller Replacing an IBM ServeRAID-BR10il SAS/SATA ControllerInstalling an IBM ServeRAID-BR10il SAS/SATA controller 4. Remove the cover see “Removing and installing the cover” on page Removing the DVD drive cable Replacing the DVD drive cableInstalling the DVD drive cable Removing a DVD drive Replacing a DVD driveInstalling a DVD drive DANGER StatementMicroprocessor Installing the virtual media keyReplacing the virtual media key Removing the virtual media keyRemoving the PCI-X riser-card power cable Replacing the PCI-X riser-card power cableUpdating the Universal Unique Identifier UUID Installing the PCI-X riser-card power cablec. From Family list, select ThinkServer RS210, and click Continue imminternalip accessmethodimmpassword uuidvalueimmuserid Updating the DMI/SMBIOS dataimmexternalip immpasswordimmpassword m/tmodelassetmethod accessmethodc. From Family list, select ThinkServer RS210, and click Continue Completing the FRU replacementd. Click Downloads and drivers immpasswordConnecting the cables Updating the server configuration Page 3. From Family list, select ThinkServer RS210, and click Continue Chapter 7. Parts listing, RS210 Types 6531, 6532, 6533, andBezel Riser card assemblyPower supply 12Table 15. Parts listing, Types Replaceable server components45J9648 Table 15. Parts listing, Types 6531 continued45J9658 45J9646Heat Sink models CTO All Models Table 15. Parts listing, Types 6531 continuedFRU# 6531 Software FRUTable 16. Parts listing, Types 46U2117 Table 16. Parts listing, Types 6532 continued33F8354 CRU part Table 16. Parts listing, Types 6532 continuedTable 17. Parts listing, Types Table 17. Parts listing, Types 6533 continued CRU part Table 17. Parts listing, Types 6533 continued46M0864 Table 17. Parts listing, Types 6533 continued46M0922 Table 18. Parts listing, Types Table 18. Parts listing, Types 6534 continued CRU part Table 18. Parts listing, Types 6534 continuedCRU part Table 18. Parts listing, Types 6534 continuedPower cords Lenovo Power cord part Table 19. Power cords, TypeLenovo Power cord part Table 20. Power cords, TypeTable 22. Power cords, Type Table 21. Power cords, TypeUsed in these countries and regions Table 22. Power cords, Type 6534 continuedLenovo Power cord part numberPage v LSI Configuration Utility program Chapter 8. Configuring the serverv Setup Utility program v Boot Manager programv System Settings Using the Setup UtilityStarting the Setup Utility Setup Utility menu choicesPOST Watchdog Timer Value PowerForce Legacy Video on Boot POST Watchdog Timerv Save Settings v Boot ManagerPower-on Password Administrator Passwordv Load Default Settings PasswordsPower-on password v Restore SettingsResetting passwords Administrator passwordTable 23. System board jumpers Configuring RAID controllers Using the Boot Manager programUsing LSI Configuration Utility program Creating a RAID array of hard disk drives Starting the LSI Configuration Utility program3. Select System Settings → Adapters and UEFI drivers Formatting a hard disk driveCreating a storage configuration using the Configuration Wizard Using the WebBIOS utilityStarting the WebBIOS utility Main menu of the WebBIOS utilityAdd Configuration Using the EasyStartup DVDClear Configuration New ConfigurationBefore you use the EasyStartup DVD Setup and configurationEasyStartup overview Typical operating system installation Configuring RAIDUpdating the firmware Installing your operating system without using EasyStartup3. From Family list, select ThinkServer RS210, and click Continue 3. From Family list, select ThinkServer RS210, and click Continue Using the EasyUpdate Firmware Updater toolStarting the backup server firmware Recovering the UEFI firmwareTable 25. System board jumpers v Command-line interface IPMI Shell Using the integrated management modulev Serial over LAN Installation order IBM Advanced Settings Utility programInstalling ThinkServer EasyManage software Installation requirements1. Click Start - Server Manager Installing Windows 2008 32-bit componentsInstalling Web Server Role IIS Installing Microsoft SNMP servicesObtaining the IP address for the IMM Uninstalling the LANDesk Software AgentUsing the remote presence capability and blue-screen capture Enabling the remote presence featureLogging on to the Web interface Configuring the Gigabit Ethernet controllersEnabling the Intel Gigabit Ethernet Utility program v Remote Console Enable v Serial Port Sharing Enable Enabling and configuring Serial over LAN SOLUEFI update and configuration b. Select System Settings → Devices and I/O PortsLenovo United States, Inc 1009 Think Place - Building One Appendix. NoticesMorrisville, NC U.S.A Attention Lenovo Director of Licensing Important notes TrademarksAppendix. Notices Product recycling and disposalTürkiye EEE Yönetmeliğine Uygunluk Beyanı Recycling statements for JapanEEE Yönetmeliğine Uygundur For the European Union Battery return programIndustry Canada Class A emission compliance statement German Ordinance for Work gloss statementElectronic emission notices Federal Communications Commission FCC statementNotice to Customers United Kingdom telecommunications safety requirementEuropean Union EMC Directive conformance statement Germany Class A compliance statementTaiwan Class A warning statement Japan Voluntary Control Council for Interference VCCI statementKorea Class A warning statement People’s Republic of China Class A warning statementAppendix. Notices Page Index A Page removing continued PCI card continuedserver continued Page Page 1P P/N Part Number Printed in USA