Replacing the oil coating roll | Lexmark 912 specification

Maintenance

9Turn the printer on.

The message Did you replace Fuser? appears.

10Press Go to reset the fuser counter.

Note: If you replaced the fuser after receiving the 80 Fuser/Belt Life Warning message or the 80 Fuser/Belt Exhausted message, see Replacing the transfer belt for instructions on replacing the transfer belt.

For instructions about replacing the transfer belt, click the following heading:

Replacing the transfer belt

Replacing the oil coating roll

Your printer monitors the life of your oil coating roll. When the oil coating roll reaches the end of its life, the printer displays 85 Coating Roll Exhausted. This message indicates that you must replace the oil coating roll to continue printing.

For best print quality, make sure you replace the oil coating roll when the printer displays

85Coating Roll Life Warning. Press Go to clear the message. The printer continues to display the Supplies message until you replace the oil coating roll.

To replace the oil coating roll, use the following steps or the instruction sheet supplied with the oil coating roll.

Replacing the oil coating roll

152

Image 157

Lexmark 912 manual Replacing the oil coating roll, Message Did you replace Fuser? appears

Contents

C912 Edition notice Table of Contents Using printer menus Troubleshooting 189 Trademarks Trademarks Licensing notice Licensing notice Electronic emission notices Safety information Industry Canada compliance statement Energy Star Noise emission levelsJapanese Vcci notice United Kingdom Telecommunications Act Printer overview Memory Print speedPaper handling Printing Understanding the operator panel Using the operator panel buttons Menu Changing printer settings Printing the menu settings Sending a job to print Menus Disabled Loading a paper tray Canceling a print job Loading paper Printing Printing Loading other paper sizes Loading the multipurpose feeder Paper dimensionsCapacity Trouble-free printing Printing Printing Loading paper, transparencies, labels, and card stock Loading envelopes Loading letterhead Closing the multipurpose feeder Close the multipurpose feeder Accessing held jobs from the operator panel Using the Print and Hold functionPrinting and deleting held jobs Repeat Print Recognizing when format errors occurReserve Print Verify Print Enter PIN Printing confidential jobs Configuring the operator panel for custom size media Using the multipurpose feederPrinting with custom size specialty media To set the paper size for the multipurpose feeder Configuring your printer’s driver For Windows NT, Windows 2000, and Windows XP For Mac OS For Mac OS X Storing print media Tips for successful printingAvoiding paper jams Resident fonts Understanding fonts Printing Printing Printing Printing Symbol sets for PCL 6 emulation Symbol setsResident bit mapped fonts ISO 6 Ascii Downloadable fonts Hebrew and Arabic fonts Euro supportFontVision Media guidelines Media guidelines Paper Duplexer Envelopes Transparencies Card stock Labels Card stock Supplies Menu Color Menu Setup MenuFinishing Menu Infrared Menu Enabling operator panel menus Disabling operator panel menus Color Color MenuCorrection Manual Color Print Mode Finishing Menu Duplex Bind DuplexHole Punch Multipage View PrintOffset Pages Separator Infrared Menu Infrared Buffer Transmit DelayJob Buffering Window Size Cancel Job Cancel FaxJob Menu Confidential Reset ActiveJob Held Jobs Network Menu SmartSwitch SetupStd Net Advanced Parallel MenuStatus Honor Init Parallel DisabledMode PCL Emul Menu Lines per Font SourceOrientation Pitch Tray Symbol SetRenumber Paper Menu ConfigureAssign Type Bins Types CustomOutput Bin Loading Paper Paper Source Paper Size Paper Type Substitute Paper WeightSize Universal Fax Menu Fax Setup Fax Logs Log Paper Type Fax Send Fax Receive Fax Output Bin PostScript Menu Baud Serial MenuData Bits Honor DSR RS-232/RS Parity422 RS-422 Serial Buffer Robust XONSerial Setup Menu Download RecoveryTarget Jam Protect Power SaverPrint Area Printer TimeoutUsage Resource Toner Alarm Staple AlarmWait Timeout 15...65535 Supplies Menu Replace Supplies LifeSupplies USB Menu USB Buffer Utilities MenuDefragment Yes Factory DefaultsRemove Held Jobs Directory Job Acct StatPrint Demo Samples Canceling Job Canceling FaxActivating Menu Changes Connection Check deviceClearing Job Accounting Stat Fuser? Disk RecoveryDisabling Menus Disk Corrupted Not Be Restored MaintenanceFormatting Disk Formatting Flash Or Cancel Job Install deviceInvalid Engine Code Invalid Installed Menus DisabledPower Saver Network Card Printer Calibrating Printing Menu SettingsPrint Jobs on Disk Printing Alignment Resetting Programming Error PxResetting the Printer Queuing and Deleting Defaults Restore Held Jobs. GoStop? Restoring Factory Config Error Emul Error LoadTray x Missing Unsupported Disk Res Save Off Deficient Short PaperMemory Insufficient Collation Insufficient Memory Held Jobs May Not Be RestoredMemory Full Complex Error Sense Error4x Unsupported Firmware Card USB Port x Disabled DisabledConfiguration Input Config Error Bins Attached Too ManyToo Many Disks Too Many Flash Format Unformatted DiskBelt Exhausted CRC Failure Engine CodeAll Photo Devs Exhausted Abnormal Service messageColor Toner Empty Identifying paper jam areas Clearing paper jams Check Areas A,B Paper Jam x Pages Jammed Check Areas A-F, T1- 5, MPF 114 115 116 117 Check Area C Check Area D 120 121 Removing small size paper from the duplex unit 123 124 125 Check Area E Check Area F 128 Paper Jam Check MP Feeder Paper Jam 24x Paper Jam Check Tray 131 Paper Jam Check Tray 133 Conserving supplies Determining supply statusToner Darkness Using the Print and Hold Canceling a print jobMultipage Print Verify Print Ordering a fuser Ordering suppliesOrdering an oil coating roll Ordering a transfer belt Order the appropriate toner cartridge Replacing supplies Recycling used supplies Storing supplies Removing a photodeveloper Replacing a photodeveloper 140 Installing a photodeveloper 142 Removing the duplex unit Replacing the transfer belt Replacing the fuser Complete the steps in Preparing for maintenance Preparing for maintenanceRemoving the fuser 145 146 147 Installing the fuser 149 150 151 Message Did you replace Fuser? appears Replacing the oil coating roll Removing the oil coating roll 154 155 Replacing the fuser Replacing the transfer belt Replacing the transfer belt Removing the transfer belt 158 159 160 Installing the transfer belt 162 163 164 Removing the duplex unit Replacing a toner cartridge Replacing a toner cartridge Removing a toner cartridge 167 Installing a toner cartridge 169 Resetting the maintenance counter 171 172 Cleaning the LEDs 174 Closing the top cover 176 Opening the top cover Replacing the fuser Clearing paper jams Removing the duplex unit 180 Removing the high capacity feeder 182 183 Removing the system board access cover Locating memory and network options Installing the system board access cover 186 Removing an optional drawer 188 Calling for service Troubleshooting Troubleshooting Multipurpose feeder for an illustration Index 193 194 195 196 197 198 199 200 201