Ok? | Nortel Networks TP-1610 SIP specs

Mediant 2000 SIP User’s Manual

K. RADIUS Billing and VXML Calling Card Application

Figure K-8: VXML Script Option 1, Make a Call
	1
	Play VP 5
		No
	DTMF Pressed?
	Yes	Play VP 3
	Yes
	Play VP 6	Go To 1
		Go To 1
	DTMF Pressed?
		No
	Yes	Play VP 3
	Play VP 7
	Waits for
	Authentication
	Authentication	No
	Finished?
	Yes
Yes	Authentication
	OK?
Go To Transfer	No
Go To Transfer
Yes	No Match
	Counter = x?
Play VP 4	No
Play VP 4
	Play VP 7
Go To End	No
	Go To 1
Version 4.4	263	July 2005

Image 263

Nortel Networks TP-1610 SIP user manual Ok?

Contents

Mediant 2000 & TP-1610 SIP User’s Manual Page Table of Contents 139 135 SNMP-Based Management 171 Diagnostics 165BootP/DHCP Support 167 201 183187 189 Appendix M Regulatory Information Appendix J SS7 TunnelingAppendix K Radius Billing and Vxml Calling Card Application Appendix L Snmp Traps 271 List of Figures 168 List of Tables 272 Related Documentation TrademarksCustomer Support Abbreviations and Terminology Overview T1 Available Configurations Available ConfigurationsService Node E1 Available Configurations SIP Overview Mediant 2000 FeaturesGeneral Features Hardware Features PSTN-to-SIP Interworking Supported SIP FeaturesSupported Interworking Features Mediant 2000 SIP User’s Manual Overview Reader’s Notes Label GeneralComponent Description TP-1610 Board Power SupplyMediant 2000 Chassis Electrical Component Sensitivity Board Hot-Swap Support Mediant 2000 SIP 2 TP-1610 Front Panel LED Indicators Rear Transition Module Rear Panel with two 50-pin Connectors for 16 Trunks Optional CPU Board Reader’s Notes Unpacking Package Contents To attach the two front side brackets, take these 3 steps Installing the Mediant 2000 in a 19-inch RackMounting the Mediant Mounting the Mediant 2000 on a Desktop Mediant 2000 Front View with 19-inch Rack Mount Brackets To attach the device to a 19-inch rack, take these 2 steps Item # Label Cabling the Mediant To cable the Mediant 2000, take these 4 steps Connecting the E1/T1 Trunk Interfaces E1/T1 Number Tx Pins Tip/Ring Rx Pins Tip/Ring Installing the Ethernet ConnectionWith RJ-48c Connectors, take these 2 steps E1/T1 Connections on each 50-pin Telco Connector Connecting the DC Power Supply Connecting the Power SupplyWhen using a dual AC power cable DC Terminal Block Screw Connector Assigning the Mediant 2000 IP Address Assigning an IP Address Using HttpTo assign an IP address using HTTP, take these 9 steps Restoring Networking Parameters to their Initial State Assigning an IP Address Using BootPTo assign an IP address using BootP, take these 4 steps To configure basic SIP parameters, take these 10 steps Configuring the Mediant 2000 Basic Parameters Mediant 2000 SIP Computer Requirements Configuration ConceptsOverview of the Embedded Web Server Limiting the Embedded Web Server to Read-Only Mode Password ControlConfiguring the Web Interface via the ini File Embedded Web Server Username & Password Unauthorized Accessing the Embedded Web ServerUsing Internet Explorer to Access the Embedded Web Server To access the Embedded Web Server, take these 4 steps Main Menu Bar Getting Acquainted with the Web Interface To save the changes to flash, take these 2 steps Saving ChangesEntering Phone Numbers in Various Tables Coders To configure the gateway’s coders, take these 6 stepsProtocol Management Protocol Definition Parameters Number Manipulation Tables Advanced Parameters Number Manipulation Parameters Description Source Phone Number Manipulation Table for Tel IP Calls Number of digits to leave Prefix / suffix to add Dialing Plan Notation Description Numbering Plans and Type of NumberNPI/TON Values for Isdn Etsi Tel to IP Routing Table Configuring the Routing Tables To configure the Tel to IP Routing table, take these 6 steps Tel to IP Routing Table Parameter Description IP to Trunk Group Routing Table Parameter Description IP to Trunk Group Routing Table IP to Trunk Group Routing Table Parameter Description To configure the internal DNS table, take these 7 stepsInternal DNS Table You can use this table for example Reasons for Alternative Routing To configure the coder group settings, take these 8 steps Configuring the Profile DefinitionsCoder Group Settings To configure the Tel Profile settings, take these 8 steps Tel Profile Settings To configure the IP Profile settings, take these 8 steps IP Profile Settings To configure the Trunk Group table, take these 4 steps Configuring the Trunk Group Table Channel or channels that correspond to the trunk group ID Trunk Group Table Parameter Description 13 Trunk Group Settings Screen Configuring the Trunk Group Settings Channel Select Modes Mode Description Configuring the Network Settings Advanced Configuration Simple Network Time Protocol Support Configuring the Snmp Managers TableTo configure the Snmp Managers Table, take these 6 steps Multiple Routers Support Mediant 2000 SIP 16 Channel Settings Screen Configuring the Channel Settings To configure the Trunk Settings, take these 9 steps Configuring the Trunk Settings Trunks Status Color Indicator Keys 18TDM Bus Settings Screen Configuring the TDM Bus Settings To back up the ini file, take these 4 steps Restoring and Backing up the Gateway ConfigurationTo restore or back up the ini file To restore the ini file, take these 4 steps 20 Regional Settings Screen Regional Settings Gateway Statistics Status & DiagnosticChanging the Mediant 2000 Username and Password To change the username and password, take these 5 steps To view the IP connectivity information, take these 2 steps Quality Info Call CountersTo view the IP Tel and Tel IP Call Counters information IP Connectivity Parameters Column Name Description Gwappreasonnotrelevant 24 Mediant 2000 Trunk & Channel Status Screen Monitoring the Mediant 2000 Trunks & Channels To activate the Message Log, take these 4 steps Activating the Internal Syslog Viewer System Information To access the System Information screen To use the Software Upgrade Wizard, take these 9 steps Software Update MenuSoftware Upgrade Wizard 30 Load a cmp File Screen 32 Load an ini File Screen Cancel Reset Voice Prompts Auxiliary Files10 Auxiliary Files Descriptions File Type Description 36 Auxiliary Files Screen Updating the Software Upgrade Key To save the changes to the non-volatile, take these 2 steps Save Configuration To reset the Mediant 2000, take these 3 steps Resetting the Mediant Reader’s Notes To modify the ini file, take these 3 steps Secured ini FileModifying an ini File Ini File Structure Rules Ini File ContentIni File Structure SIP ini File Example Ini File Example Basic, Logging, Web and Radius Parameters EnableUDPPortTranslation GWAppDelayTimeDisableNAT EnableIPAddrTranslation IPDiffServ MaxEchoCancellerLengthEchoCancellerLength BaseUDPport CDRReportLevel NTPUpdateIntervalEnableRAI GwDebugLevel RAILoopTime EnableSilenceDisconnectWeb-Related Parameters DisableWebTask RAILowThreshold HTTPport ResetWebPasswordDisableWebConfig EnableRADIUS RADIUSAuthPort BootP and Tftp Parameters IniFileURLBootPRetries BootPSelectiveEnable ExtBootPReqEnable BootPDelay Snmp Parameters SetCommunityString SIP Configuration Parameters SendInviteToProxy EnableProxySRVQueryEnableProxyKeepAlive AlwaysSendToProxy IsFallbackUsed PasswordProxyRedundancyMode IsTrustedProxy SIPDestinationPort EnableRPIheaderEnablePtime AssertedIdMode AMRPayloadType Web Parameter Name CoderName EVRCPayloadType EnableRFC2658InterleavinAMRSendRate EVRCRate EnableTransfer DefaultReleaseCauseIPAlertTimeout EnableEarlyMedia XferPrefix EnableHoldEnableForward EnableCallWaiting EnableDigitDelivery DisableAutoDTMFMuteEnableBusyOut EnableDigitDelivery2IP Profile Parameters CoderNameID TelProfileID IPProfileID PlayRBTone2Tel EnableTDMoverIPIsdn and CAS Interworking-Related Parameters PIForDisconnectMsg ProgressIndicator2ISDNProgressIndicator2IP PlayRBTone2IP ISDNTransferCapability PSTNAlertTimeoutEnableCIC EnableAOC CASTransportType AddIEinSetupISDNDMSTimerT310 ISDNJapanNTTTimerT3JA ChannelList DefaultNumberNumber Manipulation and Routing Parameters TrunkGroupx AddPortAsPrefix TrunkGroupSettingsChannelSelectMode AddTrunkGroupAsPrefix Prefix UseSourceNumberAsDisplayName AlwaysUseRouteTable Valid Range and Description Web Parameter Name SourceNumberMapIP2Tel SourceNumberMapTel2IP AltRouteCauseIP2Tel SecureCallsFromIPAltRouteCauseTel2IP AltRoutingTel2IPMode Alternative Routing Parameters AltRoutingTel2IPEnableIPConnQoSMaxAllowedDelay FilterCalls2IP 11 E1/T1 Configuration Parameters TDMBusLocalReference CASFileName1 ISDNNFASInterfaceIDxCASTableIndexx CASFileName0 MaxDigits ISDNIBehavior E1/T1/J1 Configuration Parameters continues on pages 122 toIsdn Flexible Behavior Parameters ISDNInCallsBehavior ISDNInCallsBehaviorx ISDNGeneralCCBehaviorISDNOutCallsBehavior ISDNIBehaviorx Channel Parameters ModemBypassPayloadType FaxModemBypassDJBufMinDelayFaxModemBypassM FaxBypassPayloadType EnableStandardSIDPayloadType VoiceVolumeEnableSilenceCompression EnableEchoCanceller DTMFDigitLength RFC2833PayloadTypeMGCPDTMFDetectionPoint DTMFInterDigitInterval Special Optimization Factor Value Dynamic Jitter Buffer Operation Configuration File Parameters Configuration Files Parameters Mediant 2000 SIP User’s Manual 134 Document # LTRT-72504 Number of Call Progress Tones Contains the following key Configuring the Call Progress TonesFormat of the Call Progress Tones Section in the ini File Call Progress Tone Types PRT File Format Prerecorded Tones PRT FileVoice Prompts File CAS Protocol Configuration Files Redirect Number DMS-100 NI-2 5ESS Euro Isdn Proxy or Registrar Registration ExampleRedirect Number and Calling Name Display Calling Name Display DMS-100 NI-2 5ESS Euro Isdn Isdn Overlap Dialing Nfas Interface ID Using Isdn Nfas Working with DMS-100 Switches Configuring the Dtmf Transport Types Mediant 2000 SIP User’s Manual 144 Document # LTRT-72504 MGCPDTMFDetectionPont Pstn Fallback as a Special Case of Alternative Routing Alternative Routing MechanismDetermining the Availability of Destination IP Addresses Call Transfer Working with Supplementary ServicesCall Hold and Retrieve Features Relevant Parameters Mediant 2000 SIP User’s Manual 148 Document # LTRT-72504 Implementation TDM Tunneling Ini File Example for TDM Tunneling Originating Side Field Name Description Call Detail ReportSupported CDR Fields Ini File Parameters of Gateways a and B Trunk to Trunk Routing Example Trying Ringing 200 OK Ack SIP Call Flow Example F2 10.8.201.10 == 10.8.201.108 Trying F6 10.8.201.108 == 10.8.201.10 BYE M2K-AudioCodesaudiocodes.comAudioCodes SIP Authentication Example A111432d6bce58ddf02e3b5e1c77c010d2A2 REGISTERsip10.2.2.222 SIP to PRI Calls Nortel IMS Specific Features and Configuration13.1 SIP2PRI Gateway PRI to SIP Calls Support for RPI Header Configuration of NPI/TON Other Nortel Specific Parameters Transfer 13.2 SIP2CAS Call Pilot Gateway Supported Features Dtmf Configuration Mediant 2000 SIP User’s Manual 164 Document # LTRT-72504 Syslog Support Mediant 2000 Self-Testing Sending the Syslog Messages Setting the Syslog Server To set the Syslog serverSyslog Servers Operation Startup Process BootP/DHCP Support Mediant 2000 Startup Process Upgrading the Mediant BootP SupportDhcp Support Length Vendor Specific Information FieldVendor Specific Information Field Description Value Snmp Message Standard About Snmp Snmp MIB Objects Snmp Extensibility Feature Cold Start Trap Carrier Grade Alarm SystemActive Alarm Table Alarm History TrunkPack-VoP Series Supported MIBs Third-Party Performance Monitoring Measurements AC-ANALOG-MIB AC-CONTROL-MIB AC-MEDIA-MIB AC-PSTN-MIB Mediant 2000 SIP User’s Manual 176 Document # LTRT-72504 Snmp Community Names Snmp Interface Details To change the trap community string, take these 2 steps Configuration of Trusted Managers via ini FileConfiguration of Trusted Managers via Snmp Trusted Managers To delete the final Trusted Manager, take these 2 steps Snmp PortsTo add a subsequent Trusted Manager, take these 2 steps Multiple Snmp Trap Destinations Configuration via the ini File To modify a trap destination Configuration via SnmpTo add a trap destination To delete a trap destination AudioCodes’ Element Management System To disable a trap destinationTo enable a trap destination Snmp Manager Backward Compatibility Voice Compression Echo CancellationCapacity with E1 Capacity with T1 VoIP Signaling Protocol Environmental AC Enclosure DimensionsInstallation Safety and EMC Standards Readers Notes File Name Description Table A-1 Mediant 2000 SIP Supplied Software Kit Mediant 2000 SIP User’s Manual 188 Document # LTRT-72504 Key Features When to Use the BootP/TFTPAn Overview of BootP To open the BootP/TFTP, take these 2 steps SpecificationsInstallation Loading the cmp File, Booting the Device Function Buttons on the Main Screen BootP/TFTP Application User Interface Log Window BootP Preferences Setting the Preferences Tftp Preferences Adding Clients Configuring the BootP Clients Editing Client Parameters Testing the ClientTo delete a client from the BootP Tool, take these 3 steps Deleting Clients Setting Client Parameters Table B-1 Command Line Switch Descriptions Using Command Line SwitchesTo use a Command Line Switch, take these 4 steps To delete an existing template, take these 3 steps Managing Client TemplatesTo create a new template, take these 4 steps To edit an existing template, take these 4 steps Reader’s Notes Table C-2 Defined Payload Types continues on pages 201 to Payload Types Defined in RFCDefined Payload Types Table C-1 Packet Types Defined in RFC Channel Number RTP Port Rtcp Port Default RTP/RTCP/T.38 Port AllocationTable C-3 Default RTP/RTCP/T.38 Port Allocation Configuring Fax/Modem ByPass Mode Fax/Modem SettingsConfiguring Fax Relay Mode Supporting V.34 Faxes Appendix E Mediant 2000 Clock Settings Mediant 2000 SIP User’s Manual 206 Document # LTRT-72504 Replacing the Main Corporate Logo with an Image File Replacing the Main Corporate Logo Mediant 2000 SIP User’s Manual 208 Document # LTRT-72504 Table F-2Web Appearance Customizable ini File Parameters Replacing the Background Image FileReplacing the Main Corporate Logo with a Text String Table F-1Customizable Logo ini File Parameters Table F-4Web Appearance Customizable ini File Parameters Customizing the Product NameTable F-3 Customizable Logo ini File Parameters Figure F-4 INI Parameters Screen Modifying ini File Parameters via the Web AdminPage Mediant 2000 SIP User’s Manual 212 Document # LTRT-72504 TrunkPack Downloadable Conversion Utility Appendix G Accessory Programs and Tools Figure G-2 Call Progress Tones Conversion Screen Converting a CPT ini File to a Binary dat File Figure G-3 Voice Prompts Screen Creating a Loadable Voice Prompts File Figure G-4 File Data Window To decode an encoded ini file, take these 4 steps Encoding / Decoding an ini FileTo encode an ini file, take these 6 steps Figure G-6 Prerecorded Tones Screen Creating a Loadable Prerecorded Tones File Figure G-7 File Data Window Generating textual trace/audit file for Isdn PRI protocols Pstn Trace UtilityGenerating textual trace/audit file for CAS protocols Figure H-8 Trunk Traces Mediant 2000 SIP User’s Manual 222 Document # LTRT-72504 Loading the Software Upgrade Key About the Software Upgrade KeyBacking up the Current Software Upgrade Key Figure H-1 Software Upgrade Key Screen Verifying that the Key was Successfully Loaded Troubleshooting an Unsuccessful Loading of a KeyAbort Procedure Loading the Software Upgrade Key Using BootP/TFTP Mediant 2000 SIP User’s Manual 226 Document # LTRT-72504 Description Reason Response Appendix I Release Reason Mapping Isdn Release Description Description Isdn Release Response Reason Table I-2 Mapping of SIP Response to Isdn Release Reason Mediant 2000 SIP User’s Manual 230 Document # LTRT-72504 Appendix J SS7 Tunneling MTP2 Tunneling Technology SS7 Characteristics SS7 Parameters Sigtran Interface Groups SS7MTP2ParamTimerT6SS7MTP2ParamTimerT7 SS7 Table Parameters Ini File Parameter Name Description Sigtran Interface IDsTable J-3 Sigtran Interface IDs SS7LINKROWSTATUS 3 SS7 Signaling Link SS7LINKGROUPID SS7 MTP2 Tunneling ini File Example Figure J-4 SS7 MTP2 Tunneling ini File Example MGC Version 239 July Figure J-5 SS7 MTP2 Tunneling ini File Example SG Ini File Parameters in a Table Format Table Permissions Table Indices Tables Structure Rules Tables of Parameter Value Rules in the ini File Structure Tables in the Loaded ini File Dynamic Tables versus Static Tables Benefits Features Figure K-1 Mediant 2000 Supported Architecture Supported Architecture Basic Calling Card IVR Scenario Implementation Figure K-3 Basic ini File Vxml Parameters Call Flow Description To start working with the IVR system, take these 6 steps Operation & ConfigurationConfiguration Parameters VxmlID EnableVoiceStreamingEnableVxml VoicePromptsFileNam Supported Radius Attributes Response Attributes Purpose Number Radius Server Messages AuthenticationAuthorization Accounting FeaturesVoice XML Interpreter Version 255 July Supported Elements & Attributes Version 257 July Object MenuNoinput Nomatch Version 259 July Table K-5 VoiceXML Supported Properties Property Name Provided Calling Card SystemVoice Prompts Version 261 July Figure K-7 Vxml Script Opening Menu Vxml Flow Chart OK? Figure K-9 Vxml Script, Call Transfer Procedure Figure K-10 Vxml Script, Options 2, 3 Figure K-12 Vxml Script Example continues on pages 266 to Vxml Script Example Version 267 July Mediant 2000 SIP User’s Manual 268 Document # LTRT-72504 Version 269 July Mediant 2000 SIP User’s Manual 270 Document # LTRT-72504 Component System#0 Alarm Traps Table L-5 acFeatureKeyError Alarm Trap Table L-3 acBoardTemperatureAlarm Alarm TrapTable L-4 acBoardEvResettingBoard Alarm Trap Table L-7 acBoardControllerFailureAlarm Alarm Trap Table L-6 acBoardCallResourcesAlarm Alarm TrapTable L-8 acBoardOverloadAlarm Alarm Trap Mediant 2000 SIP User’s Manual 274 Document # LTRT-72504 Component EthernetLink#0 Component AlarmManager#0Table L-10 acBoardEthernetLinkAlarm Alarm Trap Table L-9 acActiveAlarmTableOverflow Alarm Trap Trap Varbinds Other Traps Appendix M Regulatory Information FCC Statement Industry Canada NoticeDigital Device Warnings Network Information and Intent of Use Version 279 July AudioCodes Offices Worldwide International HeadquartersUSA Headquarters USA Offices