Manuals / Nortel Networks / Computer Equipment / Network Router

Nortel Networks TP-1610 SIP user manual Software Update Menu, Software Upgrade Wizard

Models: TP-1610 SIP

1 280

Download 280 pages 4.94 Kb

Page 78

Mediant 2000 SIP

5.11 Software Update Menu

The ‘Software Update’ menu enables users to upgrade the Mediant 2000 software by loading a new cmp file along with the ini and a suite of auxiliary files, or to update the existing auxiliary files.

The ‘Software Update’ menu comprises two submenus:

•Software Update Wizard (refer to Section 5.11.1 below).

•Auxiliary Files (refer to Section 5.11.2 on page 82).

Note: When upgrading the Mediant 2000 software you must load the new cmp file with all other related configuration files

5.11.1 Software Upgrade Wizard

The Software Upgrade Wizard guides users through the process of software upgrade: selecting files and loading them to the gateway. The wizard also enables users to upgrade software while maintaining the existing configuration. Using the wizard obligates users to load a cmp file. Users can choose to also use the Wizard to load the ini and auxiliary files (e.g., Call Progress Tones) but this option cannot be pursued without loading the cmp file. For the ini and each auxiliary file type, users can choose to reload an existing file, load a new file or not load a file at all.

Warning 1: The Software Upgrade Wizard requires the Mediant 2000 to be reset at the end of the process, disrupting any of its traffic. To avoid disruption, disable all traffic on the Mediant 2000 before initiating the Wizard.

Warning 2: Verify, prior to clicking the Start Software Upgrade button that no traffic is running on the device. After clicking this button a device reset is mandatory. Even if you choose to cancel the process in the middle, the device resets itself and the previous configuration burned to flash is reloaded.

To use the Software Upgrade Wizard, take these 9 steps:

1.Stop all traffic on the Mediant 2000 (refer to the note above).

2.Open the ‘Software Upgrade Wizard’ (Software Update menu > Software Upgrade Wizard); the ‘Start Software Upgrade’ screen appears.

Figure 5-29: Start Software Upgrade Screen

Mediant 2000 SIP User’s Manual

78

Document #: LTRT-72504

Image 78

Nortel Networks TP-1610 SIP user manual Software Update Menu, Software Upgrade Wizard

Contents

Mediant 2000 & TP-1610 SIP User’s Manual Page Table of Contents 135 139Diagnostics 165 BootP/DHCP Support 167SNMP-Based Management 171 189 183187 201Appendix L Snmp Traps 271 Appendix J SS7 TunnelingAppendix K Radius Billing and Vxml Calling Card Application Appendix M Regulatory InformationList of Figures 168 List of Tables 272 Abbreviations and Terminology TrademarksCustomer Support Related DocumentationOverview E1 Available Configurations Available ConfigurationsService Node T1 Available ConfigurationsHardware Features Mediant 2000 FeaturesGeneral Features SIP OverviewSupported SIP Features Supported Interworking FeaturesPSTN-to-SIP Interworking Mediant 2000 SIP User’s Manual Overview Reader’s Notes General Component DescriptionLabel Power Supply Mediant 2000 ChassisTP-1610 Board Board Hot-Swap Support Electrical Component SensitivityMediant 2000 SIP 2 TP-1610 Front Panel LED Indicators Rear Panel with two 50-pin Connectors for 16 Trunks Rear Transition ModuleOptional CPU Board Reader’s Notes Package Contents UnpackingMounting the Mediant 2000 on a Desktop Installing the Mediant 2000 in a 19-inch RackMounting the Mediant To attach the two front side brackets, take these 3 stepsTo attach the device to a 19-inch rack, take these 2 steps Mediant 2000 Front View with 19-inch Rack Mount BracketsCabling the Mediant Item # LabelConnecting the E1/T1 Trunk Interfaces To cable the Mediant 2000, take these 4 stepsE1/T1 Connections on each 50-pin Telco Connector Installing the Ethernet ConnectionWith RJ-48c Connectors, take these 2 steps E1/T1 Number Tx Pins Tip/Ring Rx Pins Tip/RingConnecting the Power Supply When using a dual AC power cableConnecting the DC Power Supply DC Terminal Block Screw Connector Assigning an IP Address Using Http To assign an IP address using HTTP, take these 9 stepsAssigning the Mediant 2000 IP Address Assigning an IP Address Using BootP To assign an IP address using BootP, take these 4 stepsRestoring Networking Parameters to their Initial State Configuring the Mediant 2000 Basic Parameters To configure basic SIP parameters, take these 10 stepsMediant 2000 SIP Configuration Concepts Overview of the Embedded Web ServerComputer Requirements Embedded Web Server Username & Password Password ControlConfiguring the Web Interface via the ini File Limiting the Embedded Web Server to Read-Only ModeTo access the Embedded Web Server, take these 4 steps Accessing the Embedded Web ServerUsing Internet Explorer to Access the Embedded Web Server UnauthorizedGetting Acquainted with the Web Interface Main Menu BarSaving Changes Entering Phone Numbers in Various TablesTo save the changes to flash, take these 2 steps Protocol Definition Parameters To configure the gateway’s coders, take these 6 stepsProtocol Management CodersAdvanced Parameters Number Manipulation TablesSource Phone Number Manipulation Table for Tel IP Calls Number Manipulation Parameters DescriptionDialing Plan Notation Number of digits to leave Prefix / suffix to addNumbering Plans and Type of Number NPI/TON Values for Isdn EtsiDescription Configuring the Routing Tables Tel to IP Routing TableTo configure the Tel to IP Routing table, take these 6 steps IP to Trunk Group Routing Table Tel to IP Routing Table Parameter DescriptionIP to Trunk Group Routing Table Parameter DescriptionTo configure the internal DNS table, take these 7 steps Internal DNS TableIP to Trunk Group Routing Table Parameter Description Reasons for Alternative Routing You can use this table for exampleConfiguring the Profile Definitions Coder Group SettingsTo configure the coder group settings, take these 8 steps Tel Profile Settings To configure the Tel Profile settings, take these 8 stepsIP Profile Settings To configure the IP Profile settings, take these 8 stepsConfiguring the Trunk Group Table To configure the Trunk Group table, take these 4 stepsTrunk Group Table Parameter Description Channel or channels that correspond to the trunk group IDConfiguring the Trunk Group Settings 13 Trunk Group Settings ScreenMode Description Channel Select ModesAdvanced Configuration Configuring the Network SettingsMultiple Routers Support Configuring the Snmp Managers TableTo configure the Snmp Managers Table, take these 6 steps Simple Network Time Protocol SupportMediant 2000 SIP Configuring the Channel Settings 16 Channel Settings ScreenConfiguring the Trunk Settings To configure the Trunk Settings, take these 9 stepsTrunks Status Color Indicator Keys Configuring the TDM Bus Settings 18TDM Bus Settings ScreenTo restore the ini file, take these 4 steps Restoring and Backing up the Gateway ConfigurationTo restore or back up the ini file To back up the ini file, take these 4 stepsRegional Settings 20 Regional Settings ScreenTo change the username and password, take these 5 steps Status & DiagnosticChanging the Mediant 2000 Username and Password Gateway StatisticsTo view the IP connectivity information, take these 2 steps IP Connectivity Parameters Column Name Description Call CountersTo view the IP Tel and Tel IP Call Counters information Quality InfoGwappreasonnotrelevant Monitoring the Mediant 2000 Trunks & Channels 24 Mediant 2000 Trunk & Channel Status ScreenActivating the Internal Syslog Viewer To activate the Message Log, take these 4 stepsTo access the System Information screen System InformationSoftware Update Menu Software Upgrade WizardTo use the Software Upgrade Wizard, take these 9 steps 30 Load a cmp File Screen 32 Load an ini File Screen Reset CancelFile Type Description Auxiliary Files10 Auxiliary Files Descriptions Voice PromptsUpdating the Software Upgrade Key 36 Auxiliary Files ScreenSave Configuration To save the changes to the non-volatile, take these 2 stepsResetting the Mediant To reset the Mediant 2000, take these 3 stepsReader’s Notes Secured ini File Modifying an ini FileTo modify the ini file, take these 3 steps Ini File Content Ini File StructureIni File Structure Rules Ini File Example SIP ini File ExampleBasic, Logging, Web and Radius Parameters EnableIPAddrTranslation GWAppDelayTimeDisableNAT EnableUDPPortTranslationBaseUDPport MaxEchoCancellerLengthEchoCancellerLength IPDiffServGwDebugLevel NTPUpdateIntervalEnableRAI CDRReportLevelRAILowThreshold EnableSilenceDisconnectWeb-Related Parameters DisableWebTask RAILoopTimeEnableRADIUS ResetWebPasswordDisableWebConfig HTTPportBootPSelectiveEnable BootP and Tftp Parameters IniFileURLBootPRetries RADIUSAuthPortBootPDelay ExtBootPReqEnableSnmp Parameters SetCommunityString SIP Configuration Parameters AlwaysSendToProxy EnableProxySRVQueryEnableProxyKeepAlive SendInviteToProxyIsTrustedProxy PasswordProxyRedundancyMode IsFallbackUsedAssertedIdMode EnableRPIheaderEnablePtime SIPDestinationPortWeb Parameter Name CoderName AMRPayloadTypeEVRCRate EnableRFC2658InterleavinAMRSendRate EVRCPayloadTypeEnableEarlyMedia DefaultReleaseCauseIPAlertTimeout EnableTransferEnableCallWaiting EnableHoldEnableForward XferPrefixEnableDigitDelivery2IP DisableAutoDTMFMuteEnableBusyOut EnableDigitDeliveryProfile Parameters CoderNameID IPProfileID TelProfileIDEnableTDMoverIP Isdn and CAS Interworking-Related ParametersPlayRBTone2Tel PlayRBTone2IP ProgressIndicator2ISDNProgressIndicator2IP PIForDisconnectMsgEnableAOC PSTNAlertTimeoutEnableCIC ISDNTransferCapabilityISDNJapanNTTTimerT3JA AddIEinSetupISDNDMSTimerT310 CASTransportTypeTrunkGroupx DefaultNumberNumber Manipulation and Routing Parameters ChannelListAddTrunkGroupAsPrefix TrunkGroupSettingsChannelSelectMode AddPortAsPrefixAlwaysUseRouteTable UseSourceNumberAsDisplayName PrefixValid Range and Description Web Parameter Name SourceNumberMapTel2IP SourceNumberMapIP2TelSecureCallsFromIP AltRouteCauseTel2IPAltRouteCauseIP2Tel FilterCalls2IP Alternative Routing Parameters AltRoutingTel2IPEnableIPConnQoSMaxAllowedDelay AltRoutingTel2IPMode11 E1/T1 Configuration Parameters TDMBusLocalReference CASFileName0 ISDNNFASInterfaceIDxCASTableIndexx CASFileName1MaxDigits ISDNInCallsBehavior E1/T1/J1 Configuration Parameters continues on pages 122 toIsdn Flexible Behavior Parameters ISDNIBehaviorISDNIBehaviorx ISDNGeneralCCBehaviorISDNOutCallsBehavior ISDNInCallsBehaviorxChannel Parameters FaxBypassPayloadType FaxModemBypassDJBufMinDelayFaxModemBypassM ModemBypassPayloadTypeEnableEchoCanceller VoiceVolumeEnableSilenceCompression EnableStandardSIDPayloadTypeDTMFInterDigitInterval RFC2833PayloadTypeMGCPDTMFDetectionPoint DTMFDigitLengthDynamic Jitter Buffer Operation Special Optimization Factor ValueConfiguration Files Parameters Configuration File ParametersMediant 2000 SIP User’s Manual 134 Document # LTRT-72504 Configuring the Call Progress Tones Format of the Call Progress Tones Section in the ini FileNumber of Call Progress Tones Contains the following key Call Progress Tone Types Prerecorded Tones PRT File Voice Prompts FilePRT File Format CAS Protocol Configuration Files Calling Name Display DMS-100 NI-2 5ESS Euro Isdn Proxy or Registrar Registration ExampleRedirect Number and Calling Name Display Redirect Number DMS-100 NI-2 5ESS Euro IsdnIsdn Overlap Dialing Using Isdn Nfas Nfas Interface IDWorking with DMS-100 Switches Configuring the Dtmf Transport Types Mediant 2000 SIP User’s Manual 144 Document # LTRT-72504 MGCPDTMFDetectionPont Alternative Routing Mechanism Determining the Availability of Destination IP AddressesPstn Fallback as a Special Case of Alternative Routing Relevant Parameters Working with Supplementary ServicesCall Hold and Retrieve Features Call TransferMediant 2000 SIP User’s Manual 148 Document # LTRT-72504 TDM Tunneling ImplementationIni File Example for TDM Tunneling Originating Side Call Detail Report Supported CDR FieldsField Name Description Trunk to Trunk Routing Example Ini File Parameters of Gateways a and BSIP Call Flow Example Trying Ringing 200 OK AckF2 10.8.201.10 == 10.8.201.108 Trying F6 10.8.201.108 == 10.8.201.10 BYE SIP Authentication Example M2K-AudioCodesaudiocodes.comAudioCodesREGISTERsip10.2.2.222 A111432d6bce58ddf02e3b5e1c77c010d2A2Nortel IMS Specific Features and Configuration 13.1 SIP2PRI GatewaySIP to PRI Calls PRI to SIP Calls Configuration of NPI/TON Support for RPI HeaderTransfer Other Nortel Specific ParametersSupported Features 13.2 SIP2CAS Call Pilot GatewayDtmf Configuration Mediant 2000 SIP User’s Manual 164 Document # LTRT-72504 Mediant 2000 Self-Testing Syslog SupportOperation Setting the Syslog Server To set the Syslog serverSyslog Servers Sending the Syslog MessagesBootP/DHCP Support Startup ProcessMediant 2000 Startup Process BootP Support Dhcp SupportUpgrading the Mediant Description Value Vendor Specific Information FieldVendor Specific Information Field LengthAbout Snmp Snmp Message StandardSnmp Extensibility Feature Snmp MIB ObjectsAlarm History Carrier Grade Alarm SystemActive Alarm Table Cold Start TrapThird-Party Performance Monitoring Measurements TrunkPack-VoP Series Supported MIBsAC-ANALOG-MIB AC-CONTROL-MIB AC-MEDIA-MIB AC-PSTN-MIB Mediant 2000 SIP User’s Manual 176 Document # LTRT-72504 Snmp Interface Details Snmp Community NamesTrusted Managers Configuration of Trusted Managers via ini FileConfiguration of Trusted Managers via Snmp To change the trap community string, take these 2 stepsSnmp Ports To add a subsequent Trusted Manager, take these 2 stepsTo delete the final Trusted Manager, take these 2 steps Configuration via the ini File Multiple Snmp Trap DestinationsTo delete a trap destination Configuration via SnmpTo add a trap destination To modify a trap destinationSnmp Manager Backward Compatibility To disable a trap destinationTo enable a trap destination AudioCodes’ Element Management SystemCapacity with T1 Echo CancellationCapacity with E1 Voice CompressionVoIP Signaling Protocol Safety and EMC Standards Enclosure DimensionsInstallation Environmental ACReaders Notes Table A-1 Mediant 2000 SIP Supplied Software Kit File Name DescriptionMediant 2000 SIP User’s Manual 188 Document # LTRT-72504 When to Use the BootP/TFTP An Overview of BootPKey Features Loading the cmp File, Booting the Device SpecificationsInstallation To open the BootP/TFTP, take these 2 stepsBootP/TFTP Application User Interface Function Buttons on the Main ScreenLog Window Setting the Preferences BootP PreferencesTftp Preferences Configuring the BootP Clients Adding ClientsDeleting Clients Testing the ClientTo delete a client from the BootP Tool, take these 3 steps Editing Client ParametersSetting Client Parameters Using Command Line Switches To use a Command Line Switch, take these 4 stepsTable B-1 Command Line Switch Descriptions To edit an existing template, take these 4 steps Managing Client TemplatesTo create a new template, take these 4 steps To delete an existing template, take these 3 stepsReader’s Notes Table C-1 Packet Types Defined in RFC Payload Types Defined in RFCDefined Payload Types Table C-2 Defined Payload Types continues on pages 201 toDefault RTP/RTCP/T.38 Port Allocation Table C-3 Default RTP/RTCP/T.38 Port AllocationChannel Number RTP Port Rtcp Port Fax/Modem Settings Configuring Fax Relay ModeConfiguring Fax/Modem ByPass Mode Supporting V.34 Faxes Appendix E Mediant 2000 Clock Settings Mediant 2000 SIP User’s Manual 206 Document # LTRT-72504 Replacing the Main Corporate Logo Replacing the Main Corporate Logo with an Image FileMediant 2000 SIP User’s Manual 208 Document # LTRT-72504 Table F-1Customizable Logo ini File Parameters Replacing the Background Image FileReplacing the Main Corporate Logo with a Text String Table F-2Web Appearance Customizable ini File ParametersCustomizing the Product Name Table F-3 Customizable Logo ini File ParametersTable F-4Web Appearance Customizable ini File Parameters Modifying ini File Parameters via the Web AdminPage Figure F-4 INI Parameters ScreenMediant 2000 SIP User’s Manual 212 Document # LTRT-72504 Appendix G Accessory Programs and Tools TrunkPack Downloadable Conversion UtilityConverting a CPT ini File to a Binary dat File Figure G-2 Call Progress Tones Conversion ScreenCreating a Loadable Voice Prompts File Figure G-3 Voice Prompts ScreenFigure G-4 File Data Window Encoding / Decoding an ini File To encode an ini file, take these 6 stepsTo decode an encoded ini file, take these 4 steps Creating a Loadable Prerecorded Tones File Figure G-6 Prerecorded Tones ScreenFigure G-7 File Data Window Pstn Trace Utility Generating textual trace/audit file for CAS protocolsGenerating textual trace/audit file for Isdn PRI protocols Figure H-8 Trunk Traces Mediant 2000 SIP User’s Manual 222 Document # LTRT-72504 About the Software Upgrade Key Backing up the Current Software Upgrade KeyLoading the Software Upgrade Key Figure H-1 Software Upgrade Key Screen Loading the Software Upgrade Key Using BootP/TFTP Troubleshooting an Unsuccessful Loading of a KeyAbort Procedure Verifying that the Key was Successfully LoadedMediant 2000 SIP User’s Manual 226 Document # LTRT-72504 Appendix I Release Reason Mapping Description Reason ResponseIsdn Release Description Table I-2 Mapping of SIP Response to Isdn Release Reason Description Isdn Release Response ReasonMediant 2000 SIP User’s Manual 230 Document # LTRT-72504 Appendix J SS7 Tunneling SS7 Characteristics MTP2 Tunneling TechnologySS7 Parameters SS7 Table Parameters SS7MTP2ParamTimerT6SS7MTP2ParamTimerT7 Sigtran Interface GroupsSigtran Interface IDs Table J-3 Sigtran Interface IDsIni File Parameter Name Description 3 SS7 Signaling Link SS7LINKROWSTATUSSS7 MTP2 Tunneling ini File Example SS7LINKGROUPIDFigure J-4 SS7 MTP2 Tunneling ini File Example MGC Version 239 July Figure J-5 SS7 MTP2 Tunneling ini File Example SG Ini File Parameters in a Table Format Table Indices Table PermissionsTables of Parameter Value Rules in the ini File Structure Tables Structure RulesDynamic Tables versus Static Tables Tables in the Loaded ini FileFeatures BenefitsSupported Architecture Figure K-1 Mediant 2000 Supported ArchitectureImplementation Basic Calling Card IVR ScenarioCall Flow Description Figure K-3 Basic ini File Vxml ParametersOperation & Configuration Configuration ParametersTo start working with the IVR system, take these 6 steps VoicePromptsFileNam EnableVoiceStreamingEnableVxml VxmlIDSupported Radius Attributes Purpose Number Response AttributesAuthentication AuthorizationRadius Server Messages Features Voice XML InterpreterAccounting Version 255 July Supported Elements & Attributes Version 257 July Nomatch MenuNoinput ObjectVersion 259 July Provided Calling Card System Voice PromptsTable K-5 VoiceXML Supported Properties Property Name Version 261 July Vxml Flow Chart Figure K-7 Vxml Script Opening MenuOK? Figure K-9 Vxml Script, Call Transfer Procedure Figure K-10 Vxml Script, Options 2, 3 Vxml Script Example Figure K-12 Vxml Script Example continues on pages 266 toVersion 267 July Mediant 2000 SIP User’s Manual 268 Document # LTRT-72504 Version 269 July Mediant 2000 SIP User’s Manual 270 Document # LTRT-72504 Alarm Traps Component System#0Table L-3 acBoardTemperatureAlarm Alarm Trap Table L-4 acBoardEvResettingBoard Alarm TrapTable L-5 acFeatureKeyError Alarm Trap Table L-6 acBoardCallResourcesAlarm Alarm Trap Table L-8 acBoardOverloadAlarm Alarm TrapTable L-7 acBoardControllerFailureAlarm Alarm Trap Mediant 2000 SIP User’s Manual 274 Document # LTRT-72504 Table L-9 acActiveAlarmTableOverflow Alarm Trap Component AlarmManager#0Table L-10 acBoardEthernetLinkAlarm Alarm Trap Component EthernetLink#0Other Traps Trap VarbindsAppendix M Regulatory Information Network Information and Intent of Use Industry Canada NoticeDigital Device Warnings FCC StatementVersion 279 July USA Offices International HeadquartersUSA Headquarters AudioCodes Offices Worldwide