Manuals / Paxar / Computer Equipment / Printer

Paxar 545 user manual Printer Operation / Adjustments, Users Manual Model

Models: 545

1 121

Download 121 pages 10.69 Kb

Page 28

26 • Printer Operation / Adjustments

B

A

Once the machine has been threaded and is pulling fabric from the supply roll the active unwind will automatically sense the tension of the fabric and adjust the pull off speed accordingly. This will result in a loop in the fabric under the active unwind sensor of about .250” as shown below.

.250

26 • Printer Operation / Adjustments

Users Manual Model 545™

Image 28

Paxar 545 user manual Printer Operation / Adjustments, Users Manual Model

Contents

Users Manual PAXAR Systems Group Manual Edition 15 FebruaryModel 545 Manual Part NumberThis page intentionally blank Contents Safety Issues / WarningsWarranty Information Location / Power RequirementsMaintenance Electrical Trouble ShootingMechanical Trouble Shooting Control Panel OperationAssembly Drawings Appendix AAppendix B Appendix CSafety Issues / Warnings ScopeIntroduction CautionsWarranty Information Limited WarrantyService PartsLocation of Printer Location / Power RequirementsRecommended Workstation Layout AC Power Line Unpacking Unpacking / InventoryShipping Cartons Ink Cartridge Return Program Inventory of ComponentsPAXAR 545 TOOL KIT #341390 Printer Description Product DescriptionPaxar Model 545 Label Printer Printer Specification Personal Computer Specifications Printer Assembly Fuse ConfigurationAC Entry See 115VAC Fuse PlacementInstalling the Power Cord 115VAC Fuse PlacementPlacement 5 X 20MM Fuse PlacementTCB Dip Switch Settings P.C. Board IdentificationInserting a PCMCIA Card Eject ButtonPrint Module Insertion and Removal Installing the Stacker Print Module Handling3/16” Long DriverInstall the stacker up-right rails. Remove one of the spring-loaded screws. Insert the spring-loaded screw through the mating hole in the up-right rail assembly. Thread the spring-loaded screw into the mounting block. Repeat the above procedure for the other rail. Remove the spring-loaded screw and washer from the top of the inner stacker rail. Place the threaded stud into the slot of the outer rail and reattach the washer, spring and nut Cable Installation Stacker CablePC Interface Cable KeyboardInstalling the Applications Software Printer Operation / Adjustments Installing and Removing Ink CartridgesPrinter Operation / Adjustments Users Manual ModelAdjusting the Unwind Loading Fabric for the First TimeThreading Diagram Printer Operation / AdjustmentsUsers Manual Model 2/0 AND 1/0 THREADING PATH NIP ROLL FEED ROLL26 Printer Operation / Adjustments Users Manual ModelWeb Guide Adjustment Open the feed roller by turning the feed lever counterclockwise Stacker Position Adjustment Stacker Label Width AdjustmentStacker Label Length Adjustment Stacker Angle AdjustmentStacker Full Level Adjustment Replenishing Fabric at End of Roll SplicesParked Position Print Head OperationPrint Position Printer Setup 8 On the front panel adjust the PRINT OFFSET STATION 1 to produce one straight continuous feed print line on the back of the label Sensor Calibration Control Panel Operation Control ButtonsStart FeedIndicator Lights StopOn Line SensorError LCD DisplayFront Panel Menu Map Front Panel Power Up / Home Screens POWER UP DIAGNOSTICS TESTSHOME SCREEN PRINTER ADJUSTMENTS PRINTHEAD CLEANINGSETUP SCREEN VERIFIER SETUP SCREENFront Panel Mode Descriptions PRINT / CUT POSITIONS This screen follows the PRINT POSITION STATION 1 screen. This screen allows the print position of station 2 to be adjusted in the feed direction PRINTHEAD CLEANING PROCEDURES Page This screen follows the PRINT HEAD CLEANING PROC screen CALIBRATE SENSORSThis screen follows the TOP REFL NOT OVER MARK screen. Place the fabric over the bottom reflective sensor so that the reflective mark is over the sensor and when NEW VALUE is at the highest value press ‘Enter’ LIFE COUNTS/VERSIONS FEATURE SETUP SCREEN Page VERIFIER SETUP Handling MaintenancePrint Module Handling Print Module Replacement / Height Adjustment Print Head Swing Arm Stop Adjustment Automated Print Head Cleaning WHAT LEVEL TO USEManual Manifold Seal Cleaning Positioning Swing Arms for Seal CleaningCleaning General Machine Cleaning Knife AdjustmentFeed Open Interlock Switch Adjustment PrintheadsCam - Lubrication Procedure Lubrication ProcedureGeneral Changing Stacker Belts MaintenanceFULL STACKER CONNECTOR 8-32 CAP SCREWS Users Manual Model64 Maintenance RIVETS JAM SENSOR HARNESS SNAP RING3. Remove the drive belt cover 4. Loosen 6-32 set screws in ends of main drive roller. See figure5. Insert an 8-32 screw into the threaded hole in the front side of the roller pin and remove the pin. See figure 9. To re-assemble, reverse procedure above 66 MaintenanceSMALL DUAL DRIVE BELTS SEE ITEM Users Manual ModelElectrical Trouble Shooting Power Up / Sign On / CommunicationsProblem Probable CauseProblem Front panel does not complete diagnostics testProbable Cause Corrective ActionFabric Advance ProblemProbable Cause Corrective ActionPrint ProblemProbable Cause Corrective ActionCut / Stack ProblemProblem Probable CauseMechanical Trouble Shooting FabricProblem Probable CauseProblem ProblemMechanical Trouble Shooting PrintSensor Locations Non-volatile Memory Reset Printer Wiring Electrical Drawings76 Electrical Drawings Users Manual ModelUsers Manual Model Electrical System SchematicElectrical Drawings Motherboard Power Connectors Error Messages Appendix AChip Upgrade Positions / Jumper Settings Appendix BHead Driver Board P/N 80 Appendix BThermal Control Board P/N 371105IJ S E E D E T A IL AFront Panel Diagnostic Descriptions Front Panel Board P/NAppendix C Ink Management / Shelf LifeAppendix D Knife MFG GuidelinesSolenoid Trigger Setting Other hints if there is still a problemMaterial Safety Data Sheet Appendix ESTABILITY Stable INCOMPATIBILITY Strong oxidizing agents VENTILATION Page Assembly Drawings Assembly DrawingsUsers Manual Model 90 Assembly Drawings Frame Assembly Cover DrawingUsers Manual Model Frame Cover Parts List Description92 Assembly Drawings Frame Assembly DrawingUsers Manual Model Frame Parts List Description94 Assembly Drawings Sub - Frame Assembly DrawingUsers Manual Model Description Sub - Frame Parts ListDescription 96 Assembly Drawings Power Unwind Assembly DrawingUsers Manual Model Description Power Unwind Parts ListDescription 98 Assembly Drawings Unwind Support Assembly DrawingUsers Manual Model Description Unwind Support Parts ListDescription Unwind Nip Roller Assembly Drawing 100 Assembly DrawingsUnwind Nip Roller Parts List Description102 Assembly Drawings Unwind Snubber Assembly DrawingUsers Manual Model Unwind Snubber Parts List Description104 Assembly Drawings Print Module Assembly DrawingUsers Manual Model Assembly Drawings Print Module Parts ListUsers Manual Model 106 Assembly Drawings Cartridge Support Deck Assembly DrawingUsers Manual Model Description Cartridge Support Deck Parts ListDescription 108 Assembly Drawings Feed Assembly DrawingUsers Manual Model Feed Parts List Description110 Assembly Drawings Feed Roller AssemblyUsers Manual Model Description Feed Roller Parts ListDescription 112 Assembly Drawings Knife Assembly DrawingUsers Manual Model Description Knife Parts ListDescription 114 Assembly Drawings Stacker Assembly Drawing - PartUsers Manual Model Description Stacker Parts List - PartDescription 116 Assembly Drawings Stacker Assembly Drawing - PartUsers Manual Model Description Stacker Parts List - PartDescription 118 Assembly Drawings Rewind Assembly DrawingUsers Manual Model Description Rewind Parts ListDescription