Manuals / Paxar / Computer Equipment / Printer

Paxar 545 user manual Stacker Position Adjustment, Stacker Label Width Adjustment

Models: 545

1 121

Download 121 pages 10.69 Kb

Page 31

Stacker Position Adjustment

Stacker Position Adjustment

•Once the web has been centered in the printer or it has stabilized from running, confirm that equal numbers of belts exist on either side of the fabric, and that the spacing to the nearest belt is the same on each side. This is achieved by loosening the stacker mount screw and moving the stacker forward or back accordingly.

Stacker Label Width Adjustment

•Slide the left and right spring loaded upright rails to the desired position.

Users Manual Model 545™

Printer Operation / Adjustments • 29

Image 31

Paxar 545 user manual Stacker Position Adjustment, Stacker Label Width Adjustment

Contents

Manual Part Number Users ManualPAXAR Systems Group Manual Edition 15 February Model 545This page intentionally blank Location / Power Requirements ContentsSafety Issues / Warnings Warranty InformationControl Panel Operation MaintenanceElectrical Trouble Shooting Mechanical Trouble ShootingAppendix C Assembly DrawingsAppendix A Appendix BCautions Safety Issues / WarningsScope IntroductionParts Warranty InformationLimited Warranty ServiceLocation of Printer Location / Power RequirementsRecommended Workstation Layout AC Power Line Unpacking Unpacking / InventoryShipping Cartons Ink Cartridge Return Program Inventory of ComponentsPAXAR 545 TOOL KIT #341390 Printer Description Product DescriptionPaxar Model 545 Label Printer Printer Specification Personal Computer Specifications See 115VAC Fuse Placement Printer AssemblyFuse Configuration AC Entry5 X 20MM Fuse Placement Installing the Power Cord115VAC Fuse Placement PlacementP.C. Board Identification TCB Dip Switch SettingsEject Button Inserting a PCMCIA CardPrint Module Insertion and Removal Driver Installing the StackerPrint Module Handling 3/16” LongInstall the stacker up-right rails. Remove one of the spring-loaded screws. Insert the spring-loaded screw through the mating hole in the up-right rail assembly. Thread the spring-loaded screw into the mounting block. Repeat the above procedure for the other rail. Remove the spring-loaded screw and washer from the top of the inner stacker rail. Place the threaded stud into the slot of the outer rail and reattach the washer, spring and nut Keyboard Cable InstallationStacker Cable PC Interface CableInstalling the Applications Software Installing and Removing Ink Cartridges Printer Operation / AdjustmentsUsers Manual Model Printer Operation / AdjustmentsLoading Fabric for the First Time Adjusting the Unwind2/0 AND 1/0 THREADING PATH NIP ROLL FEED ROLL Threading DiagramPrinter Operation / Adjustments Users Manual ModelUsers Manual Model 26 Printer Operation / AdjustmentsWeb Guide Adjustment Open the feed roller by turning the feed lever counterclockwise Stacker Label Width Adjustment Stacker Position AdjustmentStacker Angle Adjustment Stacker Label Length AdjustmentStacker Full Level Adjustment Splices Replenishing Fabric at End of RollParked Position Print Head OperationPrint Position Printer Setup 8 On the front panel adjust the PRINT OFFSET STATION 1 to produce one straight continuous feed print line on the back of the label Sensor Calibration Feed Control Panel OperationControl Buttons StartSensor Indicator LightsStop On LineLCD Display ErrorFront Panel Menu Map POWER UP DIAGNOSTICS TESTS Front Panel Power Up / Home ScreensHOME SCREEN VERIFIER SETUP SCREEN PRINTER ADJUSTMENTSPRINTHEAD CLEANING SETUP SCREENFront Panel Mode Descriptions PRINT / CUT POSITIONS This screen follows the PRINT POSITION STATION 1 screen. This screen allows the print position of station 2 to be adjusted in the feed direction PRINTHEAD CLEANING PROCEDURES Page CALIBRATE SENSORS This screen follows the PRINT HEAD CLEANING PROC screenThis screen follows the TOP REFL NOT OVER MARK screen. Place the fabric over the bottom reflective sensor so that the reflective mark is over the sensor and when NEW VALUE is at the highest value press ‘Enter’ LIFE COUNTS/VERSIONS FEATURE SETUP SCREEN Page VERIFIER SETUP Handling MaintenancePrint Module Handling Print Module Replacement / Height Adjustment Print Head Swing Arm Stop Adjustment WHAT LEVEL TO USE Automated Print Head CleaningPositioning Swing Arms for Seal Cleaning Manual Manifold Seal CleaningCleaning Printheads General Machine CleaningKnife Adjustment Feed Open Interlock Switch AdjustmentCam - Lubrication Procedure Lubrication ProcedureGeneral Users Manual Model Changing Stacker BeltsMaintenance FULL STACKER CONNECTOR 8-32 CAP SCREWS4. Loosen 6-32 set screws in ends of main drive roller. See figure 64 MaintenanceRIVETS JAM SENSOR HARNESS SNAP RING 3. Remove the drive belt cover5. Insert an 8-32 screw into the threaded hole in the front side of the roller pin and remove the pin. See figure Users Manual Model 9. To re-assemble, reverse procedure above66 Maintenance SMALL DUAL DRIVE BELTS SEE ITEMProbable Cause Electrical Trouble ShootingPower Up / Sign On / Communications ProblemCorrective Action ProblemFront panel does not complete diagnostics test Probable CauseCorrective Action Fabric AdvanceProblem Probable CauseCorrective Action PrintProblem Probable CauseProbable Cause Cut / StackProblem ProblemProbable Cause Mechanical Trouble ShootingFabric ProblemPrint ProblemProblem Mechanical Trouble ShootingSensor Locations Non-volatile Memory Reset Users Manual Model Printer WiringElectrical Drawings 76 Electrical DrawingsUsers Manual Model Electrical System SchematicElectrical Drawings Motherboard Power Connectors Appendix A Error Messages80 Appendix B Chip Upgrade Positions / Jumper SettingsAppendix B Head Driver Board P/NS E E D E T A IL A Thermal Control Board P/N 371105IJFront Panel Board P/N Front Panel Diagnostic DescriptionsInk Management / Shelf Life Appendix COther hints if there is still a problem Appendix DKnife MFG Guidelines Solenoid Trigger SettingAppendix E Material Safety Data SheetSTABILITY Stable INCOMPATIBILITY Strong oxidizing agents VENTILATION Page Assembly Drawings Assembly DrawingsUsers Manual Model 90 Assembly Drawings Frame Assembly Cover DrawingUsers Manual Model Description Frame Cover Parts List92 Assembly Drawings Frame Assembly DrawingUsers Manual Model Description Frame Parts List94 Assembly Drawings Sub - Frame Assembly DrawingUsers Manual Model Description Sub - Frame Parts ListDescription 96 Assembly Drawings Power Unwind Assembly DrawingUsers Manual Model Description Power Unwind Parts ListDescription 98 Assembly Drawings Unwind Support Assembly DrawingUsers Manual Model Description Unwind Support Parts ListDescription 100 Assembly Drawings Unwind Nip Roller Assembly DrawingDescription Unwind Nip Roller Parts List102 Assembly Drawings Unwind Snubber Assembly DrawingUsers Manual Model Description Unwind Snubber Parts List104 Assembly Drawings Print Module Assembly DrawingUsers Manual Model Assembly Drawings Print Module Parts ListUsers Manual Model 106 Assembly Drawings Cartridge Support Deck Assembly DrawingUsers Manual Model Description Cartridge Support Deck Parts ListDescription 108 Assembly Drawings Feed Assembly DrawingUsers Manual Model Description Feed Parts List110 Assembly Drawings Feed Roller AssemblyUsers Manual Model Description Feed Roller Parts ListDescription 112 Assembly Drawings Knife Assembly DrawingUsers Manual Model Description Knife Parts ListDescription 114 Assembly Drawings Stacker Assembly Drawing - PartUsers Manual Model Description Stacker Parts List - PartDescription 116 Assembly Drawings Stacker Assembly Drawing - PartUsers Manual Model Description Stacker Parts List - PartDescription 118 Assembly Drawings Rewind Assembly DrawingUsers Manual Model Description Rewind Parts ListDescription