QLogic Fibre Channel Switch | Q-Logic FIRMWARE VERSION 7.4 instruction

QLogic Fibre Channel Switch

Event Message Guide

Firmware Version 7.4

59060-05 A

Image 1

Q-Logic FIRMWARE VERSION 7.4 manual QLogic Fibre Channel Switch

Contents

QLogic Fibre Channel Switch Document Revision History Table of Contents QLogic Fibre Channel Switch Event Message Guide 59060-05 a Related Materials Intended Audience Availability Technical Support Contact Information Introduction Technical Support 59060-05 a Understanding Severity Levels Events and Event Logging Displaying the Events Using the Command Line Interface Displaying Events using the Event Browser Event Log Message Format Archiving and Downloading the Event Log Configuring the Event Log Configuring Port Alarm Thresholds Page Event Messages Fault Events FAN1MISSING Hwbadseating A1000.001E Hotreset failed and the switch is being reset Alarm EventsA1003.000D Fabric already locked by domain domainID A1003.000E Couldnt acquire lock from domain domainID A1003.0011 Segmenting, zoneset zonesetname already active A1003.0010 Segmenting, zoneset zonesetname not definedA1003.0012 Segmenting, zoneset zonesetname merge conflict A1003.0013 Segmenting, zone zonename merge conflict A1003.0016 Releasing Lock held too long by domainID A1003.0023 Fabric Busy Zoneset operation failed A1003.0025 Error reading security setA1003.0024 Request already in progress internal lock held A1003.002E Zoning merge has been rejected A1003.0030 Zone Merge rejected by remote switch A1003.0033 No memory for command completion A1003.0031 Error reading zoneset from activate direct A1003.003C Incompatible Zoning mode, Isolating link A1003.0039 Merge failed, total zone limit would be exceeded A1003.0040 Zone Member type membertype unsupported A1003.004D Port group does not contain entry for this switch A1003.0054 Failure at remote switch A1003.0050 ISL group does not contain entry for this switchA1003.004F No Zone Merge Response A1003.0064 UFC failure received from domain domainID A1004.0009 Eport Isolating due to ESC Incompatibility A1004.0008 Eport Isolating due to ELP IncompatibilityA1004.000A Eport Isolating due to EFP Domain Overlap A1004.000D Eport Isolating due to RDI SW Reject A1004.0011 Eport Isolating due to Remote switch isolatedA1004.000E Eport Isolating due to RDI Domain out of Range A1004.000F Eport Isolating due to Merge Zone Failure A1004.0015 Eport Isolating due to Invalid Attach That could not configure itself as an EPort Authorized maintenance provider A1004.0048 Eport Isolating due to Port Binding failure A1004.0041 Eport isolating due to EPort License Exceeded A1004.0049 Eport Isolating due to Remote inactive A1004.0052 Eport Isolating due to Switch Binding failureA1004.0054 Eport Isolating due to Link to self Meaning I/O blade link failure has been resolved Action None A1005.0034 System resource error contact technical support A1005.0013 Hotswap procedure failed must hardreset switchA1005.0035 System resource error contact technical support A1005.0020 A1005.003B Warning Debug logging filter level is set A1005.0039 Fabric Login Flogi from address FCaddress failedA1005.0040 Unsupported SFP within port A1005.004D ICCnumber cable not installed Alarm SET A1005.004C ICCnumber cable installed Alarm Cleared A1005.0052 Canceling IP ping as a result of a CPU switchover Was in progress. The unpack was canceled A1005.0063 CPU never entered HotStandby state A1005.0069 Primary blade seating was resolved A1005.0073Blade fault fault reported A1005.006F Hotreset Vversion Vversion is not supportedA1005.006D Unable to synchronize with NTP server A1005.0074 Blade seating is questionable A1005.0075 Blade seating problem was resolvedA1005.0076 Extraction latch is open A1005.0077 Extraction latch was closed A1006.0005 Zoning enforcement error in Nameserver A1005.009B IPSec configuration error errordescriptionA1005.0101 ipv6 duplicate address detected A1007.0001 Security Unspecified zoning enforcement error A1007.000B Security Efmd Rejected, bad revision A1007.0011 Chap failure, isolating with Invalid Attach A1007.001C Security Bad Authentication Flags A1007.0025 Security feature not supported Remote switch. All switches in the fabric must have the same Standard layout of the frame or the Challenge Handshake A1007.0033 Device deviceWWN failed port binding A1007.0034 Device devicewwn failed switch binding A2000.0001 Pwr1 removed Alarm SET A1007.0038 Device devicewwn failed switch bindingA2000.0002 Pwr2 failure Alarm SET A1007.0037 Device devicewwn failed port binding Alarm SET A2003.0003 Fan flow match Alarm Cleared A3005.0001-000C value voltage sensor shows valueV Alarm SET A3007.0001-000C Blade fault bladefault Cleared A3006.0001-000C value voltage sensor shows valueV Alarm SET A6001.0001 cmon insufficient memory A6001.0003 cmon switch failed NdclaA6001.0002 cmon blade failed Ndcla A6001.0004 cmon Blade was removed during Ndcla Event Messages Alarm Events 8300.000C Zoning Couldnt acquire lock from domain domainID Critical Events Switch The switch is being shutdown please wait Switch The switch is being reset please waitSwitch The switch is proceeding with a hotreset Switch The switch is now performing a hotreset Switch IOn Blade was inserted 8400.000E Switch Upgrading Licensed Ports to numberofportsSwitch IOn FC4G16 Blade was removed Switch CPUn CPU Blade was removed Complete Switch Upgrading License for multiple ISL capability Switch Upgrading License for 4G capabilitySwitch New licenses are being installed 8400.004E Switch ntpdate synchronization lost Switch radius All Radius servers failed to respond Switch The switch WWN is being upgraded8400.005D Switch Upgrading License for SANdoctor 8400.005F Switch Upgrading License for SMI-S capability Switch New firmware has been installed Blade was powered off 8400.006A Switch Upgrading License for Fabric SecurityBlade was powered on Upgrading License for Fault Tolerant capability Secondary CPU firmware update complete 8400.007C CPUn Switching over to Secondary bladeID8400.008A a Zoning merge has occurred Event Messages Critical Events Downed to due to unavailable licenses will be restarted 8B00.0009 Unable to send test result for profile profile Connection failure, fabric limited to two switches 8F00.000D Switch Status status 8B00.0014 Successful recovery of Smtp communications8B00.0012 Critical protocol failure with Smtp server 8F00.000C Fabric Status status User Releasing Lock held too long by accountname Switch Attempted unauthenticated login username accountnameUser Releasing Lock held too long by domainID User SFC received with unknown operation operationcode Switch that are no longer in use EPort will be reset in an attempt to reestablish the ISL Failure, the Response field provides more detail Informative Events Zoning New Active ZoneSet zonesetname Mserver Rejecting request commandcommandZoning Processing zoning requests, Checkpoint not permitted Zoning Reading zoning database, Checkpoint not permitted Zoning Removing all inactive zoning objects Switch a zoning configuration edit session has been canceled Switch a CIM edit session has been canceled Switch Hotreset not permitted at this time, try again later PortApp Port portnumber Cancelling Online Test 8400.008C CallHome configuration has changedEPort In Fabric Reconfiguration DNS lookup for hostname failed 8700.000B EPort Hotreset prohibited, fabric is busy EPort Port portnumber Inter-Switch Link ISL Offline8700.000C EPort Hotreset prohibited, fabric is busy 8F00.0007 Switch Added 8F00.000C Fabric Status status