8F00.000C Fabric Status status | Q-Logic FIRMWARE VERSION 7.4

3 – Event Messages Informative Events

S

(I) (8F00.000C) Fabric Status status

Meaning:	The severity of the fabric status has changed. The description field
	will show the reason for fabric status.
(I) (8F00.000D) Switch Status status
Meaning:	The severity of the switch status has changed. The description field
	will show the reason for the switch status.
(I) (8F00:000E) Link Status status
Meaning:	The severity of the link status has changed. The description field
	will show the reason for link status.

3-70	59060-05 A

Image 84

Q-Logic FIRMWARE VERSION 7.4 manual 8F00.000C Fabric Status status

Contents

QLogic Fibre Channel Switch Document Revision History Table of Contents QLogic Fibre Channel Switch Event Message Guide 59060-05 a Intended Audience Related Materials Technical Support Availability Contact Information Introduction Technical Support 59060-05 a Events and Event Logging Understanding Severity Levels Displaying Events using the Event Browser Displaying the Events Using the Command Line Interface Event Log Message Format Configuring the Event Log Archiving and Downloading the Event Log Configuring Port Alarm Thresholds Page Fault Events Event Messages FAN1MISSING Hwbadseating Alarm Events A1000.001E Hotreset failed and the switch is being resetA1003.000D Fabric already locked by domain domainID A1003.000E Couldnt acquire lock from domain domainID A1003.0010 Segmenting, zoneset zonesetname not defined A1003.0011 Segmenting, zoneset zonesetname already activeA1003.0012 Segmenting, zoneset zonesetname merge conflict A1003.0013 Segmenting, zone zonename merge conflict A1003.0016 Releasing Lock held too long by domainID A1003.0025 Error reading security set A1003.0023 Fabric Busy Zoneset operation failedA1003.0024 Request already in progress internal lock held A1003.0030 Zone Merge rejected by remote switch A1003.002E Zoning merge has been rejected A1003.0031 Error reading zoneset from activate direct A1003.0033 No memory for command completion A1003.0039 Merge failed, total zone limit would be exceeded A1003.003C Incompatible Zoning mode, Isolating link A1003.004D Port group does not contain entry for this switch A1003.0040 Zone Member type membertype unsupported A1003.0050 ISL group does not contain entry for this switch A1003.0054 Failure at remote switchA1003.004F No Zone Merge Response A1003.0064 UFC failure received from domain domainID A1004.0008 Eport Isolating due to ELP Incompatibility A1004.0009 Eport Isolating due to ESC IncompatibilityA1004.000A Eport Isolating due to EFP Domain Overlap A1004.0011 Eport Isolating due to Remote switch isolated A1004.000D Eport Isolating due to RDI SW RejectA1004.000E Eport Isolating due to RDI Domain out of Range A1004.000F Eport Isolating due to Merge Zone Failure A1004.0015 Eport Isolating due to Invalid Attach That could not configure itself as an EPort Authorized maintenance provider A1004.0041 Eport isolating due to EPort License Exceeded A1004.0048 Eport Isolating due to Port Binding failure A1004.0052 Eport Isolating due to Switch Binding failure A1004.0049 Eport Isolating due to Remote inactiveA1004.0054 Eport Isolating due to Link to self Meaning I/O blade link failure has been resolved Action None A1005.0013 Hotswap procedure failed must hardreset switch A1005.0034 System resource error contact technical supportA1005.0035 System resource error contact technical support A1005.0020 A1005.0039 Fabric Login Flogi from address FCaddress failed A1005.003B Warning Debug logging filter level is setA1005.0040 Unsupported SFP within port A1005.004C ICCnumber cable installed Alarm Cleared A1005.004D ICCnumber cable not installed Alarm SET A1005.0052 Canceling IP ping as a result of a CPU switchover Was in progress. The unpack was canceled A1005.0063 CPU never entered HotStandby state A1005.0069 Primary blade seating was resolved A1005.006F Hotreset Vversion Vversion is not supported A1005.0073Blade fault fault reportedA1005.006D Unable to synchronize with NTP server A1005.0075 Blade seating problem was resolved A1005.0074 Blade seating is questionableA1005.0076 Extraction latch is open A1005.0077 Extraction latch was closed A1005.009B IPSec configuration error errordescription A1006.0005 Zoning enforcement error in NameserverA1005.0101 ipv6 duplicate address detected A1007.0001 Security Unspecified zoning enforcement error A1007.000B Security Efmd Rejected, bad revision A1007.0011 Chap failure, isolating with Invalid Attach A1007.001C Security Bad Authentication Flags A1007.0025 Security feature not supported Remote switch. All switches in the fabric must have the same Standard layout of the frame or the Challenge Handshake A1007.0034 Device devicewwn failed switch binding A1007.0033 Device deviceWWN failed port binding A1007.0038 Device devicewwn failed switch binding A2000.0001 Pwr1 removed Alarm SETA2000.0002 Pwr2 failure Alarm SET A1007.0037 Device devicewwn failed port binding Alarm SET A2003.0003 Fan flow match Alarm Cleared A3005.0001-000C value voltage sensor shows valueV Alarm SET A3006.0001-000C value voltage sensor shows valueV Alarm SET A3007.0001-000C Blade fault bladefault Cleared A6001.0003 cmon switch failed Ndcla A6001.0001 cmon insufficient memoryA6001.0002 cmon blade failed Ndcla A6001.0004 cmon Blade was removed during Ndcla Event Messages Alarm Events Critical Events 8300.000C Zoning Couldnt acquire lock from domain domainID Switch The switch is being reset please wait Switch The switch is being shutdown please waitSwitch The switch is proceeding with a hotreset Switch The switch is now performing a hotreset 8400.000E Switch Upgrading Licensed Ports to numberofports Switch IOn Blade was insertedSwitch IOn FC4G16 Blade was removed Switch CPUn CPU Blade was removed Complete Switch Upgrading License for 4G capability Switch Upgrading License for multiple ISL capabilitySwitch New licenses are being installed 8400.004E Switch ntpdate synchronization lost Switch The switch WWN is being upgraded Switch radius All Radius servers failed to respond8400.005D Switch Upgrading License for SANdoctor 8400.005F Switch Upgrading License for SMI-S capability Switch New firmware has been installed 8400.006A Switch Upgrading License for Fabric Security Blade was powered offBlade was powered on Upgrading License for Fault Tolerant capability 8400.007C CPUn Switching over to Secondary bladeID Secondary CPU firmware update complete8400.008A a Zoning merge has occurred Event Messages Critical Events Downed to due to unavailable licenses will be restarted Connection failure, fabric limited to two switches 8B00.0009 Unable to send test result for profile profile 8B00.0014 Successful recovery of Smtp communications 8F00.000D Switch Status status8B00.0012 Critical protocol failure with Smtp server 8F00.000C Fabric Status status Switch Attempted unauthenticated login username accountname User Releasing Lock held too long by accountnameUser Releasing Lock held too long by domainID User SFC received with unknown operation operationcode Switch that are no longer in use EPort will be reset in an attempt to reestablish the ISL Failure, the Response field provides more detail Informative Events Mserver Rejecting request commandcommand Zoning New Active ZoneSet zonesetnameZoning Processing zoning requests, Checkpoint not permitted Zoning Reading zoning database, Checkpoint not permitted Switch a zoning configuration edit session has been canceled Zoning Removing all inactive zoning objects Switch Hotreset not permitted at this time, try again later Switch a CIM edit session has been canceled 8400.008C CallHome configuration has changed PortApp Port portnumber Cancelling Online TestEPort In Fabric Reconfiguration DNS lookup for hostname failed EPort Port portnumber Inter-Switch Link ISL Offline 8700.000B EPort Hotreset prohibited, fabric is busy8700.000C EPort Hotreset prohibited, fabric is busy 8F00.0007 Switch Added 8F00.000C Fabric Status status