Panel Mounting | Raymarine 300 specs

Chapter 5: Installation

5-9

4.Secure the gasket to the rear of the unit:

Remove the protective paper from the adhesive side of the gasket (this is the side that is to be affixed to the unit) then press the gasket onto the rear case, covering the screws.

5.Fit the unit to the trunnion, adjust the display angle and tighten the knobs.

6.Connect the Power/NMEA and GPS cables to the unit, avoiding tight bends in the cables.

Panel Mounting

CAUTION:

Make sure that there are no hidden electrical wires or other items behind the location before proceeding. Make sure that there is sufficient rear access for mounting and cabling.

The unit can be panel mounted, using the panel-mounting kit (accessory) available from your local Raymarine dealer.

➤Referring to Figure 5-5, panel mount the unit as follows:

1.Check the selected location for the unit. A clear, flat area at least 7.67in (195mm) wide by 4.33in (110mm) high, with at least 5in (125mm) of clearance behind the panel, is required.

2.Unpack the (optional) panel-mounting kit.

3.Using the supplied template, trace out the display unit cut-out and mark the drilling centers for the four securing holes outside of the cut-out area.

4.To provide start holes for removing the cut-out, drill four 3/8 in (10mm) holes in each opposing corner of the cut-out area.

5.Drill out the four 3/16 in (5mm) securing holes as indicated on the tem- plate. It is recommended that a 1/16 in (1mm) pilot hole is drilled first.

6.Using a suitable saw, cut along the inside edge of the cut-out line.

7.Remove the trunnion (yoke) knobs and carefully pry off the (black) ratchet inserts from the unit case.

8.Offer up the unit to the cut-out ensuring that it fits in the cut-out area.

9.Offer up the gasket to the unit ensuring that it lines up with the brass inserts in the case.

Note: The gasket must be fitted to ensure EMC compliance.

10.Remove the protective paper from the adhesive side of the gasket (this is the side that is to be affixed to the unit).

11.Press the gasket onto the unit and slide the unit into the panel cut-out.

Image 103

Raymarine 300 manual Panel Mounting

Contents

Raynav 300 GPS Plotter Page Waas Satellite Differential GPS Raynav 300 GPS Plotter Owner’s Handbook Extended Offshore Coverage Availability of the Waas System in North America Accuracy and Continuation of Broadcast Coverage Coverage Outside of North AmericaPrelim Pages Technical Accuracy WarrantyPreface EMC Conformance Contents Raynav 300 Plotter Viii Prelim Pages Maintenance Routine Checks How this Handbook is Organized Introduction Display Modes FeaturesGeneral Display Plotter Functions Plotter DisplayDisplay Functions GPS Data Pages Operating Controls Moving the Cursor Trackpad and Cursor Dedicated Keys Text Label FeatureContext-Sensitive Cursor Control Pop-Up Menus Soft Keys Waypoint List Database Lists Conventions Used Power On/OffSimulator 5050000N WPT RNG 00106000W 0.55nm 42% 60% Changing the Lighting and Contrast Controlling the Display Selecting the Display Mode 12.0ktsDATA 320M Depth 12.5m 55nmSpeed 11kts 050M Panning the Display Using Find ShipPlotter Display Control Functions Moving Around the Plotter Screen Changing the Display Scale Changing the Display Center Customizing the Display Options Switching the Cursor Data Box On/off Switching Grid On/off Simulator Mode Raynav 300 GPS Plotter Operation Changing the Display Mode Data Display Pages GPS Data GPS/Waypoint Data 123400 Waypoint Data RNG 0.55 nm Boat Data Boat/Environment Data Auto Environment Data Kts CDI Data CDI/BDI DataBDI Data Data Boxes 300T Data Log CMG Introduction Working with Waypoints 17 Waypoint Soft Keys Placing a Waypoint NEW Waypoint WPT Position Loran TDs 23 Waypoint Soft Keys Selecting a Waypoint Editing Waypoint Details Waypoint Data Display 25 Waypoint Symbol Selection Moving a Waypoint Erasing a Waypoint 26 ST80 Navigator Keypad Using the ST60 or ST80 Navigator Keypad Selecting an Entry in the Waypoint List Raynav 300 GPS Plotter Working with Routes NEW Route Creating a New Route 30 Route Soft Keys 31 Make Route Soft Keys Save Route Saving the Current Route Full Route Details Displaying Route Information Info for Route NEW Route Route Leg and Waypoint Information Clearing the Current Route from the Screen 37 Stop Follow Soft Keys Retrieve a Route from the Database Using the Route List to Erase or Name a Route Inserting a Waypoint into a Route Editing a RouteAdding/Removing Waypoints at the End of the Route Reversing the Route Removing a Waypoint from within the Route Going To an Individual Target Point Following Routes and Going to Waypoints Follow a Route Lowing ROUTE. Cancel Route and Goto CURSOR? Press the Follow Route soft key Other Follow Route Options Advancing to a Waypoint Restart Cross Track Error XTEStop Follow or Stop Goto Joining a Route Target Point Arrival Receiving Waypoints from Other Equipment Transferring Waypoints and RoutesDisplayed SeaTalk Waypoints Transferring Database Lists Sending Waypoints to Other Equipment Using Tracks 41 Track Interval Setting Guide Setting Up a Track Clearing the Current Track 42 Set Up Soft Keys Managing Tracks SmartRouteSaving and Naming the Current Track Save TRACK, Name Track or Erase Track soft key Naming, Erasing and Showing a Track 2nm Man Overboard MOB External Alarms Alarms & TimersAlarmIndicates 47 Alarms Set Up Menu Setting Alarms and Timers Cursor Echo Raynav 300 GPS Plotter Setting Up the GPS Plotter To set the default parameters Changing the Set Up Parameters Factory New Menu Options Default System Set Up Parameters Cursor Reference Bearing Mode Key Beep Cursor ReadoutDay/Night Help Units Menu Timeout PeriodAuto Mode Autopilot Pop Up Cursor Echo Nmea OUT Set UpDate and Time Settings Manual Mode Language GPS SourceGPS SOG/COG Filter Nmea Input Chart Orientation Plotter Set Up ParametersFactory New Parameter Options Default Vectors Waypoint SymbolsDefault Waypoint Symbol Waypoint Numbers Datum Selection Position Offset Fix Mode GPS Set Up Differential GPS SET UP GPS Set Up Beacon Frequency GPS ModeSignal Strength and Signal to Noise Ratio Beacon ID Differential Age Restart GPS Raynav 300 GPS Plotter EMC Installation Guidelines Installation Connections to Other Equipment Suppression Ferrites Supplied with Unpacking and Inspecting the ComponentsItems Missing? Registering this Product Surface Mounting GPS Antenna Installation Surface Mounting Arrangement Refer to Figure Pole Mounting Plotter Installation Trunnion yoke Mounting Raynav 300 GPS Plotter Dimensions Panel Mounting Panel Mounting Connecting to Other Equipment Cable Running Connectors PWR/NMEA Connector Antenna Connector Function Color Maximum Power Cable Extension Lengths SeaTalk Connector System Check and Initial Switch OnSystem Check Checking the Plotter Operation Initial Switch On Raynav 300 GPS Plotter EMC Servicing and Safety Guidelines MaintenanceRoutine Checks Power-on Setting Resetting the SystemDisposal Problem Corrective Action Problem Solving Raynav 300 GPS Plotter Appendix a Technical Summary Feature Description Face Memory Capacity Data Received Source Appendix B SeaTalk and Nmea Data RMB, APB, BWC, BWR Data Output SeaTalk Nmea Out Abbreviation Meaning Appendix C List of Abbreviations Raynav 300 GPS Plotter Important Read Carefully Page GPS Antenna Mounting Template Raynav 300 Plotter 03 in 102.3 mm Cut out shaded area only Raynav 300 GPS Plotter Index Xii See also Waas Managing Xiv Waas Xvi Limited Warranty Warranty Certificate Warranty Limitations Factory Service Centers