Antenna Connector, PWR/NMEA Connector | Raymarine 300 instruction

5-12	Raynav 300 GPS Plotter

Antenna Connector

The ANTENNA connector provides power and RF connection to the associated GPS Antenna.

CAUTION:

Do not connect/disconnect the GPS Antenna from the display unit whilst power is applied. Such action could cause irreparable damage.

➤Connect the antenna using the attached cable, as follows:

1.If not already installed, mount the GPS Antenna as described in Section 5.3.

2.Feed the cable through to the rear of the Plotter.

3.Coil up any unused cable in an appropriate safe space out of view. Do not bend the cable tighter than 4in (100mm) radius.

4.Screw the cable connector fully into its mating connector on the Plot- ter.

5.Ensure that the protective boot covers the connector.

Note: If the supplied cable is too short, use an extension cable (Part# E36011), or consult your Raymarine dealer.

It is recommended that only a single extension cable is used as each extra connector will reduce signal levels.

PWR/NMEA Connector

CAUTION:

If you do not have a breaker in your power circuit, you must fit an in-line 1A quick-blow fuse to the positive (red) lead of the power cable.

This unit is not intended for use on positive ground vessels.

The Plotter is intended for use on vessels’ DC power systems operating in the range 12VDC to 24VDC (9.0VDC to 32.0VDC maximum range). A 5ft (1.5m) power cable is supplied.

The power connections should be made at a DC power distribution panel through an isolator switch, a 1A circuit breaker or a 1A quick blow fuse. Check that all connections are clean and tight.

The DC power system should be either:

•Negative ground, with the negative battery terminal connected to the vessel’s ground.

•Floating, with neither battery terminal connected to the vessel’s ground.

Image 106

Raymarine 300 manual Antenna Connector, PWR/NMEA Connector

Contents

Raynav 300 GPS Plotter Page Raynav 300 GPS Plotter Owner’s Handbook Waas Satellite Differential GPS Availability of the Waas System in North America Extended Offshore Coverage Accuracy and Continuation of Broadcast Coverage Coverage Outside of North AmericaPrelim Pages EMC Conformance WarrantyPreface Technical Accuracy Contents Raynav 300 Plotter Viii Prelim Pages Maintenance Routine Checks Introduction How this Handbook is Organized Display FeaturesGeneral Display Modes Plotter Functions Plotter DisplayDisplay Functions Operating Controls GPS Data Pages Trackpad and Cursor Moving the Cursor Dedicated Keys Text Label FeatureContext-Sensitive Cursor Control Soft Keys Pop-Up Menus Database Lists Waypoint List Conventions Used Power On/OffSimulator 5050000N WPT RNG 00106000W 0.55nm Changing the Lighting and Contrast 42% 60% Selecting the Display Mode Controlling the Display 050M 320M Depth 12.5m 55nmSpeed 11kts 12.0ktsDATA Moving Around the Plotter Screen Using Find ShipPlotter Display Control Functions Panning the Display Changing the Display Center Changing the Display Scale Switching the Cursor Data Box On/off Customizing the Display Options Simulator Mode Switching Grid On/off Raynav 300 GPS Plotter Changing the Display Mode Operation Data Display Pages GPS/Waypoint Data GPS Data 123400 RNG 0.55 nm Waypoint Data Boat/Environment Data Boat Data Auto Kts Environment Data CDI Data CDI/BDI DataBDI Data 300T Data Boxes CMG Data Log Working with Waypoints Introduction Placing a Waypoint 17 Waypoint Soft Keys NEW Waypoint WPT Position Loran TDs Selecting a Waypoint 23 Waypoint Soft Keys Waypoint Data Display Editing Waypoint Details 25 Waypoint Symbol Selection Erasing a Waypoint Moving a Waypoint Using the ST60 or ST80 Navigator Keypad 26 ST80 Navigator Keypad Selecting an Entry in the Waypoint List Raynav 300 GPS Plotter Working with Routes Creating a New Route NEW Route 30 Route Soft Keys 31 Make Route Soft Keys Saving the Current Route Save Route Displaying Route Information Full Route Details Info for Route NEW Route Clearing the Current Route from the Screen Route Leg and Waypoint Information 37 Stop Follow Soft Keys Using the Route List to Erase or Name a Route Retrieve a Route from the Database Inserting a Waypoint into a Route Editing a RouteAdding/Removing Waypoints at the End of the Route Removing a Waypoint from within the Route Reversing the Route Following Routes and Going to Waypoints Going To an Individual Target Point Lowing ROUTE. Cancel Route and Goto CURSOR? Follow a Route Other Follow Route Options Press the Follow Route soft key Joining a Route Restart Cross Track Error XTEStop Follow or Stop Goto Advancing to a Waypoint Target Point Arrival Transferring Database Lists Transferring Waypoints and RoutesDisplayed SeaTalk Waypoints Receiving Waypoints from Other Equipment Using Tracks Sending Waypoints to Other Equipment Setting Up a Track 41 Track Interval Setting Guide 42 Set Up Soft Keys Clearing the Current Track Managing Tracks SmartRouteSaving and Naming the Current Track Naming, Erasing and Showing a Track Save TRACK, Name Track or Erase Track soft key Man Overboard MOB 2nm External Alarms Alarms & TimersAlarmIndicates Setting Alarms and Timers 47 Alarms Set Up Menu Cursor Echo Raynav 300 GPS Plotter Setting Up the GPS Plotter Changing the Set Up Parameters To set the default parameters System Set Up Parameters Factory New Menu Options Default Bearing Mode Cursor Reference Help Cursor ReadoutDay/Night Key Beep Autopilot Pop Up Menu Timeout PeriodAuto Mode Units Manual Mode Nmea OUT Set UpDate and Time Settings Cursor Echo Nmea Input GPS SourceGPS SOG/COG Filter Language Chart Orientation Plotter Set Up ParametersFactory New Parameter Options Default Waypoint Numbers Waypoint SymbolsDefault Waypoint Symbol Vectors Position Offset Datum Selection GPS Set Up Fix Mode GPS Set Up Differential GPS SET UP Beacon ID GPS ModeSignal Strength and Signal to Noise Ratio Beacon Frequency Restart GPS Differential Age Raynav 300 GPS Plotter Installation EMC Installation Guidelines Suppression Ferrites Connections to Other Equipment Registering this Product Unpacking and Inspecting the ComponentsItems Missing? Supplied with GPS Antenna Installation Surface Mounting Surface Mounting Arrangement Pole Mounting Refer to Figure Plotter Installation Raynav 300 GPS Plotter Dimensions Trunnion yoke Mounting Panel Mounting Connecting to Other Equipment Panel Mounting Connectors Cable Running Antenna Connector PWR/NMEA Connector Maximum Power Cable Extension Lengths Function Color SeaTalk Connector System Check and Initial Switch OnSystem Check Initial Switch On Checking the Plotter Operation Raynav 300 GPS Plotter EMC Servicing and Safety Guidelines MaintenanceRoutine Checks Power-on Setting Resetting the SystemDisposal Problem Solving Problem Corrective Action Raynav 300 GPS Plotter Feature Description Appendix a Technical Summary Face Memory Capacity Appendix B SeaTalk and Nmea Data Data Received Source Data Output SeaTalk Nmea Out RMB, APB, BWC, BWR Appendix C List of Abbreviations Abbreviation Meaning Raynav 300 GPS Plotter Important Read Carefully Page GPS Antenna Mounting Template Raynav 300 Plotter Cut out shaded area only 03 in 102.3 mm Raynav 300 GPS Plotter Index Xii See also Waas Managing Xiv Waas Xvi Warranty Certificate Limited Warranty Warranty Limitations Factory Service Centers