Manuals / Raymarine / Marine Equipment / Marine GPS System

Raymarine 300 manual SmartRoute, Managing Tracks, Saving and Naming the Current Track

Models: 300

1 136

Download 136 pages 59.73 Kb

Page 72

3-44	Raynav 300 GPS Plotter

i.To clear the track without saving it in the Track List, press NO.

ii.To save the track in the list, press YES.

The NAME TRACK soft keys are displayed and you should continue as described in Saving and Naming the Current Track below.

The current track is cleared from the screen.

3. To return to the default soft key display, press CLEAR.

SmartRoute

SmartRoute enables the current track, or last segment of a track with breaks, to be converted to a route.

➤To convert the current track into a route:

1.Select MAKE INTO ROUTE and press ENTER.

The current track/last segment is converted to a new route, with the most recently placed track point as the start of the route, ie. the track is reversed.

If there is an unsaved current route on screen, the option to save the route is given, see Section 3.4, Working with Routes.

2.Check the route and, in particular, that the route deviation from the original, given in the warning box, is within navigable limits.

Managing Tracks

It is a staightforward task to set up a Current Track which is retained even if you switch off your display unit. In addition, up to five different tracks can be saved so that you can use them at a later date. This section explains how to perform the following tasks:

•Save and name the Current Track.

•Name, Erase and Show a previously saved track.

Saving and Naming the Current Track

Up to five named tracks can be held in the Track List. These tracks can be retrieved at a later date.

➤To save and name the current track:

1.Press the TRACK LIST soft key. The track list pop-up and associated soft keys are displayed.

2.The next available entry on the track list is highlighted. If required, use the trackpad to select an alternative position in the list; this can be a blank slot, or an existing track that you no longer require.

3.Press SAVE TRACK. The Name Track soft keys are displayed as shown in Figure 3-45.

Image 72

Raymarine 300 manual SmartRoute, Managing Tracks, Saving and Naming the Current Track

Contents

Raynav 300 GPS Plotter Owner’s HandbookPage SAFETY NOTICES Raynav 300 GPS Plotter Owner’s HandbookWAAS Satellite Differential GPS Prelim PagesAvailability of the WAAS System in North America Extended Offshore CoverageFigure i The WAAS System Coverage Outside of North America Accuracy and Continuation of Broadcast CoverageFigure ii WAAS Coverage Map Warranty PrefaceEMC Conformance Technical AccuracyContents - Raynav 300 Plotter ChapterSAFETY NOTICES ChapterUsing the Route List to Erase or Name a Route ChapterOperation Setting Up the GPS Plotter InstallationChapter ChapterChapter 6 Maintenance & Fault Finding Appendix A Technical SummaryAppendix B SeaTalk and NMEA Data Appendix C List of AbbreviationsChapter 1 Overview 1.1 IntroductionHow this Handbook is Organized 1.2 Features GeneralDisplay Display Modes1.3 The Plotter Display Plotter FunctionsDisplay Functions 1.4 Operating Controls GPS Data PagesTrackpad and Cursor Moving the CursorDedicated Keys Context-Sensitive Cursor ControlALARMS SET UP Soft KeysPop-Up Menus Note If the key text is greyed out, it is not currently availableDatabase Lists WAYPOINT LISTPOSITION 348 m2.2 Power On/Off Chapter 2 Getting Started2.1 Introduction Conventions UsedSD-FIX GPS STATUS1.0 D-FIX STEER STARBOARDNote Factory default settings are LIGHT OFF and CONTRAST 50% Changing the Lighting and ContrastSelecting the Display Mode 2.3 Controlling the DisplayFigure 2-5 Display Modes 5050000W00106000W Chapter 2 Getting StartedUsing FIND SHIP 2.4 Plotter Display Control FunctionsMoving Around the Plotter Screen Panning the DisplayChanging the Display Center Changing the Display ScaleSwitching the Cursor Data Box On/off Customizing the Display OptionsSimulator Mode Switching Grid On/off2-10 Raynav 300 GPS Plotter3.2 Changing the Display Mode Chapter 3 Operation3.1 Introduction Data Display Pages 320 M 0.55 nm050 M 12.0 kts320M 0.55nm050M 12.0kts0.06 nm 01 h00 mRNG 0.55 nm 133400BRG 320M RNG 0.55nmDEPTH 12.5 m SPEED 11ktsAUTO LOCK 323M0.05nm DEPTH 12.5MWIND TRUE WIND APPEnvironment Data Figure 3-11 Environment Data #10.05nm 300T23.2nm CDI/BDI Data28.7nm 124T MANUAL Data Boxes104018 17kts 124T 0.05nmTIME Data LogPOSITION 3.3 Working with Waypoints IntroductionPlacing a Waypoint WAYPOINT LISTPOSITION 348 mNEW WAYPOINT 124 mRNG 12.6 nm Figure 3-19 New Waypoint ScreenWPT POSITION LORAN TDs 3-15Figure 3-20 Waypoint Position Screen Loran TDs Figure 3-21 Select Chain/Slaves ScreenSelecting a Waypoint Figure 3-23 Waypoint Soft KeysWaypoint Data Display Editing Waypoint DetailsNote The ERASE WPT soft key is only available via the Waypoint List Figure 3-25 Waypoint Symbol Selection D49091Erasing a Waypoint Moving a WaypointUsing the ST60 or ST80 Navigator Keypad Figure 3-26 ST80 Navigator KeypadSelecting an Entry in the Waypoint List Editing Entries in the Waypoint, Route, or Track ListsTo edit an item in a list using the Navigator Keypad 3.4 Working with Routes Figure 3-27 Default Soft Keys Typical Creating a New RouteWAYPOINTS NEW ROUTETo make a new route by placing waypoints using the cursor Figure 3-31 Make Route Soft Keys D4928-1Saving the Current Route SAVE ROUTEDisplaying Route Information Full Route DetailsROUTE LIST INFO FOR ROUTE - NEW ROUTE Clearing the Current Route from the Screen Route Leg and Waypoint InformationCLEAR D4961-1 D4915-1Using the Route List to Erase or Name a Route Retrieve a Route from the DatabaseEditing a Route Inserting a Waypoint into a RouteAdding/Removing Waypoints at the End of the Route Removing a Waypoint from within the Route Reversing the Routei. Press REVERSE ROUTE 3.5 Following Routes and Going to Waypoints Going To an Individual Target PointNote The soft keys differ if a follow or goto is already in progress LOWING ROUTE. CANCEL ROUTE AND GOTO CURSOR? Follow a RouteOther Follow Route Options Note You cannot remove a waypoint from a route if it is the targetRestart Cross Track Error XTE Stop Follow or Stop GotoJoining a Route Advancing to a WaypointTarget Point Arrival 3.6 Transferring Waypoints and Routes Displayed SeaTalk WaypointsTransferring Database Lists Receiving Waypoints from Other Equipment3.7 Using Tracks Sending Waypoints to Other EquipmentSetting Up a Track Figure 3-41 Track Interval Setting GuideClearing the Current Track SmartRoute Managing TracksSaving and Naming the Current Track Naming, Erasing and Showing a Track 3.8 Man Overboard MOB MOB DR0.33 nm 162 T3.9 Alarms & Timers External AlarmsSetting Alarms and Timers Figure 3-47 Alarms Set Up MenuALARMS SET UP 3.10 Cursor Echo 3-50 Raynav 300 GPS PlotterChapter 4 Setting Up the GPS Plotter Track, detailed in Using Tracks on page4.1 Introduction 4.2 Changing the Set Up Parameters Figure 4-1 Set Up Soft Keys4.3 System Set Up Parameters Table 4-1 System Set Up ParametersChapter 4 Setting Up the GPS Plotter DefaultBearing Mode Table 4-1 System Set Up Parameters ContinuedCursor Reference Note The alarms continue to sound Cursor ReadoutDay/Night HelpMenu Timeout Period Auto ModeAutopilot Pop Up UnitsNMEA OUT Set Up Date and Time SettingsManual Mode Note The remote display must have SeaTalk Cursor Out enabledGPS Source GPS SOG/COG FilterNMEA Input Language4.4 Plotter Set Up Parameters Chart OrientationTable 4-2 Plotter Set Up Parameters Waypoint Symbols Default Waypoint SymbolWaypoint Numbers VectorsPosition Offset Datum Selection4.5 GPS Set Up Fix ModeGPS STATUS 1.0 D-FIXD-GPS Set Up DIFFERENTIAL GPS SET UPD-GPS Mode Signal Strength and Signal to Noise RatioBeacon ID Beacon FrequencyRestart GPS Differential Age4-16 Raynav 300 GPS PlotterChapter 5 Installation EMC Installation Guidelines5.1 Introduction Suppression Ferrites Connections to Other EquipmentFigure 5-1 Typical Suppression Ferrites System Parts and Accessories 5.2 Unpacking and Inspecting the ComponentsItems Missing? Registering this Product5.3 GPS Antenna Installation Surface MountingTop view Underside viewD47251 Pole Mounting Figure 5-3 Pole Mounting Arrangement5.4 Plotter Installation Figure 5-4 Raynav 300 GPS Plotter Dimensions Trunnion yoke MountingRaynav 300 GPS Plotter Panel Mounting Note The gasket must be fitted to ensure EMC compliance5.5 Connecting to Other Equipment Figure 5-5 Panel MountingConnectors 5.6 Cable RunningIntroduction Antenna Connector PWR/NMEA ConnectorThis unit is not intended for use on positive ground vessels Table 5-2 Power/NMEA Connections FunctionColor 5.7 System Check and Initial Switch On SeaTalk ConnectorSystem Check EMC ConformanceInitial Switch On SYSTEM SET UP MENUChecking the Plotter Operation 5-16 Raynav 300 GPS PlotterChapter 6 Maintenance & Fault Finding 6.1 MaintenanceEMC Servicing and Safety Guidelines Routine Checks6.2 Resetting the System Disposal6.3 Problem Solving Note The factory default settings are listed in ChapterRaynav 300 GPS Plotter Appendix A Technical Summary Appendix A Technical SummaryFeature DescriptionFeature Built in Lithium battery giving ~5 yearsDescription From a PC serial port via the NMEA interAppendix B SeaTalk and NMEA Data Appendix B SeaTalk and NMEA DataData Received SourceThe following data, if available, are transmitted on the SeaTalk port Data OutputSeaTalk NMEA OutAppendix C List of Abbreviations Appendix C List of AbbreviationsAbbreviation MeaningRaynav 300 GPS Plotter SiRF LICENSE AGREEMENT IMPORTANT - READ CAREFULLY 3. LIMITED WARRANTY REMEDIES DISCLAIMER LIMITATION OF LIABILITYPage Installation Templates GPS Antenna Mounting TemplateRaynav 300 Plotter Raynav 300 GPS Plotter Mounting Template Installation TemplatesCut out shaded area only 300/320 TemplateRaynav 300 GPS Plotter Index see also WAAS EMC see also WAAS Managing Page Page Page Warranty Certificate Limited WarrantyInstalled Warranty Obtaining Warranty ServiceWarranty Limitations Factory Service Centers Sales & Order ServicesUnited States of America UK, Europe, Middle East, Far East