Manuals / Raymarine / Marine Equipment / Marine GPS System

Raymarine 300 manual NMEA OUT Set Up, Cursor Echo, Date and Time Settings, Manual Mode

Models: 300

1 136

Download 136 pages 59.73 Kb

Page 85

Chapter 4: Setting Up the GPS Plotter

4-7

4.The current manual variation value, if no SeaTalk or NMEA value and no position data is available.

Manual Mode

If MANUAL mode is selected, by pressing either of the MANUAL soft keys, the local variation value can be specified according to the area in which you are operating. Press the appropriate MANUAL soft key to adjust the variation up or down, to a maximum of 30° East or West.

This value is then transmitted to any other SeaTalk instruments on your system. It is retained if you turn the display off and on again.

In Manual mode, incoming NMEA variation is ignored. However, if the variation is changed on another SeaTalk instrument, the new value is used and the manual value that is displayed is updated.

Note: The Manual variation value defaults to 0°, so it is important to set up a value if variation is not available from an external source.

NMEA OUT Set Up

Each NMEA sentence can be set to either OFF or ON individually. The factory default is ON for each sentence.

Cursor Echo

You can set up your system so that radars, plotters and chartplotters connected via SeaTalk can display each other’s cursors.

Press the CURSOR ECHO soft key to display the cursor transfer soft keys. The following options can be toggled ON or OFF:

•Radar Cursor In: displays the cursor from another radar on the plot- ter display or chart window (default - OFF).

•Chart Cursor In: displays the cursor from another plotter or chart- plotter (default - OFF).

•SeaTalk Cursor Out: enables the output, onto SeaTalk, of the dis- play’s own cursor (default - OFF).

Note: The remote display must have SeaTalk Cursor Out enabled.

If you set the options to OFF, no cursor echo information is displayed.

Date and Time Settings

Set your preferred date format (DD/MM/YY or MM/DD/YY) and time format (12 or 24 hour). If you wish to display local time, use the soft keys to change from UTC to the required time offset. This can be up to ±13 hours, in hourly steps.

Image 85

Raymarine 300 manual NMEA OUT Set Up, Cursor Echo, Date and Time Settings, Manual Mode

Contents

Owner’s Handbook Raynav 300 GPS PlotterPage Raynav 300 GPS Plotter Owner’s Handbook SAFETY NOTICESWAAS Satellite Differential GPS Prelim PagesExtended Offshore Coverage Availability of the WAAS System in North AmericaFigure i The WAAS System Accuracy and Continuation of Broadcast Coverage Coverage Outside of North AmericaFigure ii WAAS Coverage Map Preface WarrantyEMC Conformance Technical AccuracyChapter Contents - Raynav 300 PlotterSAFETY NOTICES ChapterChapter Using the Route List to Erase or Name a RouteOperation Installation Setting Up the GPS PlotterChapter ChapterAppendix A Technical Summary Chapter 6 Maintenance & Fault FindingAppendix B SeaTalk and NMEA Data Appendix C List of Abbreviations1.1 Introduction Chapter 1 OverviewHow this Handbook is Organized General 1.2 FeaturesDisplay Display ModesPlotter Functions 1.3 The Plotter DisplayDisplay Functions GPS Data Pages 1.4 Operating ControlsMoving the Cursor Trackpad and CursorContext-Sensitive Cursor Control Dedicated KeysSoft Keys ALARMS SET UPPop-Up Menus Note If the key text is greyed out, it is not currently availableWAYPOINT LIST Database ListsPOSITION 348 mChapter 2 Getting Started 2.2 Power On/Off2.1 Introduction Conventions UsedGPS STATUS SD-FIX1.0 D-FIX STEER STARBOARDChanging the Lighting and Contrast Note Factory default settings are LIGHT OFF and CONTRAST 50%2.3 Controlling the Display Selecting the Display Mode5050000W Figure 2-5 Display Modes00106000W Chapter 2 Getting Started2.4 Plotter Display Control Functions Using FIND SHIPMoving Around the Plotter Screen Panning the DisplayChanging the Display Scale Changing the Display CenterCustomizing the Display Options Switching the Cursor Data Box On/offSwitching Grid On/off Simulator ModeRaynav 300 GPS Plotter 2-10Chapter 3 Operation 3.2 Changing the Display Mode3.1 Introduction Data Display Pages 0.55 nm 320 M050 M 12.0 kts0.55nm 320M050M 12.0kts01 h00 m 0.06 nmRNG 0.55 nm 133400RNG 0.55nm BRG 320MDEPTH 12.5 m SPEED 11ktsLOCK 323M AUTO0.05nm DEPTH 12.5MWIND APP WIND TRUEEnvironment Data Figure 3-11 Environment Data #1300T 0.05nm23.2nm CDI/BDI DataData Boxes 28.7nm 124T MANUAL104018 17kts 124T 0.05nmData Log TIMEPOSITION Introduction 3.3 Working with WaypointsWAYPOINT LIST Placing a WaypointPOSITION 348 m124 m NEW WAYPOINTRNG 12.6 nm Figure 3-19 New Waypoint Screen3-15 WPT POSITION LORAN TDsFigure 3-20 Waypoint Position Screen Loran TDs Figure 3-21 Select Chain/Slaves ScreenFigure 3-23 Waypoint Soft Keys Selecting a WaypointEditing Waypoint Details Waypoint Data DisplayNote The ERASE WPT soft key is only available via the Waypoint List D49091 Figure 3-25 Waypoint Symbol SelectionMoving a Waypoint Erasing a WaypointFigure 3-26 ST80 Navigator Keypad Using the ST60 or ST80 Navigator KeypadEditing Entries in the Waypoint, Route, or Track Lists Selecting an Entry in the Waypoint ListTo edit an item in a list using the Navigator Keypad 3.4 Working with Routes Creating a New Route Figure 3-27 Default Soft Keys TypicalWAYPOINTS NEW ROUTETo make a new route by placing waypoints using the cursor D4928-1 Figure 3-31 Make Route Soft KeysSAVE ROUTE Saving the Current RouteFull Route Details Displaying Route InformationROUTE LIST INFO FOR ROUTE - NEW ROUTE Route Leg and Waypoint Information Clearing the Current Route from the ScreenCLEAR D4915-1 D4961-1Retrieve a Route from the Database Using the Route List to Erase or Name a RouteInserting a Waypoint into a Route Editing a RouteAdding/Removing Waypoints at the End of the Route Reversing the Route Removing a Waypoint from within the Routei. Press REVERSE ROUTE Going To an Individual Target Point 3.5 Following Routes and Going to WaypointsNote The soft keys differ if a follow or goto is already in progress Follow a Route LOWING ROUTE. CANCEL ROUTE AND GOTO CURSOR?Note You cannot remove a waypoint from a route if it is the target Other Follow Route OptionsStop Follow or Stop Goto Restart Cross Track Error XTEJoining a Route Advancing to a WaypointTarget Point Arrival Displayed SeaTalk Waypoints 3.6 Transferring Waypoints and RoutesTransferring Database Lists Receiving Waypoints from Other EquipmentSending Waypoints to Other Equipment 3.7 Using TracksFigure 3-41 Track Interval Setting Guide Setting Up a TrackClearing the Current Track Managing Tracks SmartRouteSaving and Naming the Current Track Naming, Erasing and Showing a Track MOB DR 3.8 Man Overboard MOB0.33 nm 162 TExternal Alarms 3.9 Alarms & TimersFigure 3-47 Alarms Set Up Menu Setting Alarms and TimersALARMS SET UP 3.10 Cursor Echo Raynav 300 GPS Plotter 3-50Track, detailed in Using Tracks on page Chapter 4 Setting Up the GPS Plotter4.1 Introduction Figure 4-1 Set Up Soft Keys 4.2 Changing the Set Up ParametersTable 4-1 System Set Up Parameters 4.3 System Set Up ParametersChapter 4 Setting Up the GPS Plotter DefaultTable 4-1 System Set Up Parameters Continued Bearing ModeCursor Reference Cursor Readout Note The alarms continue to soundDay/Night HelpAuto Mode Menu Timeout PeriodAutopilot Pop Up UnitsDate and Time Settings NMEA OUT Set UpManual Mode Note The remote display must have SeaTalk Cursor Out enabledGPS SOG/COG Filter GPS SourceNMEA Input LanguageChart Orientation 4.4 Plotter Set Up ParametersTable 4-2 Plotter Set Up Parameters Default Waypoint Symbol Waypoint SymbolsWaypoint Numbers VectorsDatum Selection Position OffsetFix Mode 4.5 GPS Set UpGPS STATUS 1.0 D-FIXDIFFERENTIAL GPS SET UP D-GPS Set UpSignal Strength and Signal to Noise Ratio D-GPS ModeBeacon ID Beacon FrequencyDifferential Age Restart GPSRaynav 300 GPS Plotter 4-16EMC Installation Guidelines Chapter 5 Installation5.1 Introduction Connections to Other Equipment Suppression FerritesFigure 5-1 Typical Suppression Ferrites 5.2 Unpacking and Inspecting the Components System Parts and AccessoriesItems Missing? Registering this ProductSurface Mounting 5.3 GPS Antenna InstallationUnderside view Top viewD47251 Figure 5-3 Pole Mounting Arrangement Pole Mounting5.4 Plotter Installation Trunnion yoke Mounting Figure 5-4 Raynav 300 GPS Plotter DimensionsRaynav 300 GPS Plotter Note The gasket must be fitted to ensure EMC compliance Panel MountingFigure 5-5 Panel Mounting 5.5 Connecting to Other Equipment5.6 Cable Running ConnectorsIntroduction PWR/NMEA Connector Antenna ConnectorThis unit is not intended for use on positive ground vessels Function Table 5-2 Power/NMEA ConnectionsColor SeaTalk Connector 5.7 System Check and Initial Switch OnSystem Check EMC ConformanceSYSTEM SET UP MENU Initial Switch OnChecking the Plotter Operation Raynav 300 GPS Plotter 5-166.1 Maintenance Chapter 6 Maintenance & Fault FindingEMC Servicing and Safety Guidelines Routine ChecksDisposal 6.2 Resetting the SystemNote The factory default settings are listed in Chapter 6.3 Problem SolvingRaynav 300 GPS Plotter Appendix A Technical Summary Appendix A Technical SummaryFeature DescriptionBuilt in Lithium battery giving ~5 years FeatureDescription From a PC serial port via the NMEA interAppendix B SeaTalk and NMEA Data Appendix B SeaTalk and NMEA DataData Received SourceData Output The following data, if available, are transmitted on the SeaTalk portSeaTalk NMEA OutAppendix C List of Abbreviations Appendix C List of AbbreviationsAbbreviation MeaningRaynav 300 GPS Plotter 3. LIMITED WARRANTY REMEDIES DISCLAIMER LIMITATION OF LIABILITY SiRF LICENSE AGREEMENT IMPORTANT - READ CAREFULLYPage GPS Antenna Mounting Template Installation TemplatesRaynav 300 Plotter Installation Templates Raynav 300 GPS Plotter Mounting TemplateCut out shaded area only 300/320 TemplateRaynav 300 GPS Plotter Index see also WAAS EMC see also WAAS Managing Page Page Page Limited Warranty Warranty CertificateInstalled Warranty Obtaining Warranty ServiceWarranty Limitations Sales & Order Services Factory Service CentersUnited States of America UK, Europe, Middle East, Far East