Manuals / Raymarine / Marine Equipment / Marine GPS System

Raymarine 300 Sd-Fix, Gps Status, D-Fix, Steer Starboard, 5050000N WPT RNG 00106000W 0.55nm, 320M

Models: 300

1 136

Page 20

2-2	Raynav 300 GPS Plotter

GPS STATUS

SAT SIGNAL STATUS SAT SIGNAL STATUS

15 LOCKED 23 LOCKED

09 IN USE 18 IN USE

08 IN USE 26 IN USE

10 LOCKED 12 LOCKED

20 LOCKED 14 LOCKED

17 LOCKED 03 LOCKED

HDOP		FIX STATUS

1.0D-FIX

FIX	MODE		D-GPS	RESTART
GPS	D	SD	SET UP	GPS

D5551_1

Figure 2-1: GPS Status Screen

The GPS Status screen is displayed until a satellite fix has been acquired. When satellite acquisition is complete, the READY FOR NAVIGATION pop-up box displays for two seconds.

To proceed whilst satellite acquisition continues, press the CLEAR key; the GPS Data Screen is displayed.

SD-FIX	WPT BRG

320°M

50°50^000N WPT RNG 001°06^000W 0.55nm

COG

				050°M

					SOG
STEER STARBOARD			12.0kts
	WPT 004		12.0kts


ROUTE	GOTO	GPS DATA			WPT DATA

D4936-1

Figure 2-2: GPS Data Screen

➤To switch the display unit off, press and hold the POWER key for at least three seconds. A 3-second countdown timer is displayed; when it reaches

Page 20

Image 20

Raymarine 300 manual Sd-Fix, Gps Status, D-Fix, Steer Starboard, 5050000N WPT RNG 00106000W 0.55nm, 320M, 050M, 12.0kts

Contents

Raynav 300 GPS Plotter Owner’s HandbookPage SAFETY NOTICES Raynav 300 GPS Plotter Owner’s HandbookWAAS Satellite Differential GPS Prelim PagesFigure i The WAAS System Availability of the WAAS System in North AmericaExtended Offshore Coverage Figure ii WAAS Coverage Map Coverage Outside of North AmericaAccuracy and Continuation of Broadcast Coverage Warranty PrefaceEMC Conformance Technical AccuracyContents - Raynav 300 Plotter ChapterSAFETY NOTICES ChapterOperation Using the Route List to Erase or Name a RouteChapter Setting Up the GPS Plotter InstallationChapter ChapterChapter 6 Maintenance & Fault Finding Appendix A Technical SummaryAppendix B SeaTalk and NMEA Data Appendix C List of AbbreviationsHow this Handbook is Organized Chapter 1 Overview1.1 Introduction 1.2 Features GeneralDisplay Display ModesDisplay Functions 1.3 The Plotter DisplayPlotter Functions 1.4 Operating Controls GPS Data PagesTrackpad and Cursor Moving the CursorDedicated Keys Context-Sensitive Cursor ControlALARMS SET UP Soft KeysPop-Up Menus Note If the key text is greyed out, it is not currently availableDatabase Lists WAYPOINT LISTPOSITION 348 m2.2 Power On/Off Chapter 2 Getting Started2.1 Introduction Conventions UsedSD-FIX GPS STATUS1.0 D-FIX STEER STARBOARDNote Factory default settings are LIGHT OFF and CONTRAST 50% Changing the Lighting and ContrastSelecting the Display Mode 2.3 Controlling the DisplayFigure 2-5 Display Modes 5050000W00106000W Chapter 2 Getting StartedUsing FIND SHIP 2.4 Plotter Display Control FunctionsMoving Around the Plotter Screen Panning the DisplayChanging the Display Center Changing the Display ScaleSwitching the Cursor Data Box On/off Customizing the Display OptionsSimulator Mode Switching Grid On/off2-10 Raynav 300 GPS Plotter3.1 Introduction 3.2 Changing the Display ModeChapter 3 Operation Data Display Pages 320 M 0.55 nm050 M 12.0 kts320M 0.55nm050M 12.0kts0.06 nm 01 h00 mRNG 0.55 nm 133400BRG 320M RNG 0.55nmDEPTH 12.5 m SPEED 11ktsAUTO LOCK 323M0.05nm DEPTH 12.5MWIND TRUE WIND APPEnvironment Data Figure 3-11 Environment Data #10.05nm 300T23.2nm CDI/BDI Data28.7nm 124T MANUAL Data Boxes104018 17kts 124T 0.05nmPOSITION TIMEData Log 3.3 Working with Waypoints IntroductionPlacing a Waypoint WAYPOINT LISTPOSITION 348 mNEW WAYPOINT 124 mRNG 12.6 nm Figure 3-19 New Waypoint ScreenWPT POSITION LORAN TDs 3-15Figure 3-20 Waypoint Position Screen Loran TDs Figure 3-21 Select Chain/Slaves ScreenSelecting a Waypoint Figure 3-23 Waypoint Soft KeysNote The ERASE WPT soft key is only available via the Waypoint List Waypoint Data DisplayEditing Waypoint Details Figure 3-25 Waypoint Symbol Selection D49091Erasing a Waypoint Moving a WaypointUsing the ST60 or ST80 Navigator Keypad Figure 3-26 ST80 Navigator KeypadSelecting an Entry in the Waypoint List Editing Entries in the Waypoint, Route, or Track ListsTo edit an item in a list using the Navigator Keypad 3.4 Working with Routes Figure 3-27 Default Soft Keys Typical Creating a New RouteWAYPOINTS NEW ROUTETo make a new route by placing waypoints using the cursor Figure 3-31 Make Route Soft Keys D4928-1Saving the Current Route SAVE ROUTEROUTE LIST Displaying Route InformationFull Route Details INFO FOR ROUTE - NEW ROUTE CLEAR Clearing the Current Route from the ScreenRoute Leg and Waypoint Information D4961-1 D4915-1Using the Route List to Erase or Name a Route Retrieve a Route from the DatabaseAdding/Removing Waypoints at the End of the Route Editing a RouteInserting a Waypoint into a Route i. Press REVERSE ROUTE Removing a Waypoint from within the RouteReversing the Route Note The soft keys differ if a follow or goto is already in progress 3.5 Following Routes and Going to WaypointsGoing To an Individual Target Point LOWING ROUTE. CANCEL ROUTE AND GOTO CURSOR? Follow a RouteOther Follow Route Options Note You cannot remove a waypoint from a route if it is the targetRestart Cross Track Error XTE Stop Follow or Stop GotoJoining a Route Advancing to a WaypointTarget Point Arrival 3.6 Transferring Waypoints and Routes Displayed SeaTalk WaypointsTransferring Database Lists Receiving Waypoints from Other Equipment3.7 Using Tracks Sending Waypoints to Other EquipmentSetting Up a Track Figure 3-41 Track Interval Setting GuideClearing the Current Track Saving and Naming the Current Track SmartRouteManaging Tracks Naming, Erasing and Showing a Track 3.8 Man Overboard MOB MOB DR0.33 nm 162 T3.9 Alarms & Timers External AlarmsALARMS SET UP Setting Alarms and TimersFigure 3-47 Alarms Set Up Menu 3.10 Cursor Echo 3-50 Raynav 300 GPS Plotter4.1 Introduction Chapter 4 Setting Up the GPS PlotterTrack, detailed in Using Tracks on page 4.2 Changing the Set Up Parameters Figure 4-1 Set Up Soft Keys4.3 System Set Up Parameters Table 4-1 System Set Up ParametersChapter 4 Setting Up the GPS Plotter DefaultCursor Reference Bearing ModeTable 4-1 System Set Up Parameters Continued Note The alarms continue to sound Cursor ReadoutDay/Night HelpMenu Timeout Period Auto ModeAutopilot Pop Up UnitsNMEA OUT Set Up Date and Time SettingsManual Mode Note The remote display must have SeaTalk Cursor Out enabledGPS Source GPS SOG/COG FilterNMEA Input LanguageTable 4-2 Plotter Set Up Parameters 4.4 Plotter Set Up ParametersChart Orientation Waypoint Symbols Default Waypoint SymbolWaypoint Numbers VectorsPosition Offset Datum Selection4.5 GPS Set Up Fix ModeGPS STATUS 1.0 D-FIXD-GPS Set Up DIFFERENTIAL GPS SET UPD-GPS Mode Signal Strength and Signal to Noise RatioBeacon ID Beacon FrequencyRestart GPS Differential Age4-16 Raynav 300 GPS Plotter5.1 Introduction Chapter 5 InstallationEMC Installation Guidelines Figure 5-1 Typical Suppression Ferrites Suppression FerritesConnections to Other Equipment System Parts and Accessories 5.2 Unpacking and Inspecting the ComponentsItems Missing? Registering this Product5.3 GPS Antenna Installation Surface MountingD47251 Top viewUnderside view Pole Mounting Figure 5-3 Pole Mounting Arrangement5.4 Plotter Installation Raynav 300 GPS Plotter Figure 5-4 Raynav 300 GPS Plotter DimensionsTrunnion yoke Mounting Panel Mounting Note The gasket must be fitted to ensure EMC compliance5.5 Connecting to Other Equipment Figure 5-5 Panel MountingIntroduction Connectors5.6 Cable Running This unit is not intended for use on positive ground vessels Antenna ConnectorPWR/NMEA Connector Color Table 5-2 Power/NMEA ConnectionsFunction 5.7 System Check and Initial Switch On SeaTalk ConnectorSystem Check EMC ConformanceChecking the Plotter Operation Initial Switch OnSYSTEM SET UP MENU 5-16 Raynav 300 GPS PlotterChapter 6 Maintenance & Fault Finding 6.1 MaintenanceEMC Servicing and Safety Guidelines Routine Checks6.2 Resetting the System Disposal6.3 Problem Solving Note The factory default settings are listed in ChapterRaynav 300 GPS Plotter Appendix A Technical Summary Appendix A Technical SummaryFeature DescriptionFeature Built in Lithium battery giving ~5 yearsDescription From a PC serial port via the NMEA interAppendix B SeaTalk and NMEA Data Appendix B SeaTalk and NMEA DataData Received SourceThe following data, if available, are transmitted on the SeaTalk port Data OutputSeaTalk NMEA OutAppendix C List of Abbreviations Appendix C List of AbbreviationsAbbreviation MeaningRaynav 300 GPS Plotter SiRF LICENSE AGREEMENT IMPORTANT - READ CAREFULLY 3. LIMITED WARRANTY REMEDIES DISCLAIMER LIMITATION OF LIABILITYPage Installation Templates GPS Antenna Mounting TemplateRaynav 300 Plotter Raynav 300 GPS Plotter Mounting Template Installation TemplatesCut out shaded area only 300/320 TemplateRaynav 300 GPS Plotter Index see also WAAS EMC see also WAAS Managing Page Page Page Warranty Certificate Limited WarrantyInstalled Warranty Obtaining Warranty ServiceWarranty Limitations Factory Service Centers Sales & Order ServicesUnited States of America UK, Europe, Middle East, Far East

GPS STATUS

1.0D-FIX

SD-FIX

320°M

50°50^000N WPT RNG 001°06^000W 0.55nm

050°M

STEER STARBOARD

12.0kts