Manuals / Raymarine / Marine Equipment / Marine GPS System

Raymarine 300 manual Plotter Installation

Models: 300

1 136

Download 136 pages 59.73 Kb

Page 101

Chapter 5: Installation

5-7

5.4 Plotter Installation

The display unit can be mounted using the trunnion (yoke) bracket, or panel mounted using the optional Panel Mounting Kit.

When planning the installation of your Raynav 300, the following points should be considered:

•Convenience: The unit should be installed in a convenient position where it can be viewed straight on or with a viewing angle of less than 35°. You may wish to apply power, before you install the unit, to deter- mine the best viewing angle prior to fixing. The mounting location should be easily accessible to allow operation of the front panel con- trols.

•Access: There must be sufficient space behind the display unit to allow cable connections to the rear panel connectors, avoiding tight bends in the cable.

•Interference: The selected location should be far enough away from devices that may cause interference, such as motors and generators (see the EMC Installation Guidelines earlier in this chapter).

•Cable runs: The unit must be located near a DC power source. The power cable supplied is 1.5m, but a longer cable can be used if required. Power must be supplied via a 1A quick blow fuse or circuit breaker. Refer to Section 5.6, Cable Running.

•Environment: The unit should be protected from physical damage, heat sources and excessive vibration. Although the unit is waterproof, it is good practice to mount it in a protected area away from prolonged and direct exposure to rain and/or salt spray. Refit the Sun Cover when not in use to avoid damage to the LCD screen.

The dimensions of the unit, including the bracket, are shown in

Figure 5-4.

Image 101

Raymarine 300 manual Plotter Installation

Contents

Owner’s Handbook Raynav 300 GPS PlotterPage Raynav 300 GPS Plotter Owner’s Handbook SAFETY NOTICESWAAS Satellite Differential GPS Prelim PagesFigure i The WAAS System Availability of the WAAS System in North AmericaExtended Offshore Coverage Figure ii WAAS Coverage Map Coverage Outside of North AmericaAccuracy and Continuation of Broadcast Coverage Preface WarrantyEMC Conformance Technical AccuracyChapter Contents - Raynav 300 PlotterSAFETY NOTICES ChapterOperation Using the Route List to Erase or Name a RouteChapter Installation Setting Up the GPS PlotterChapter ChapterAppendix A Technical Summary Chapter 6 Maintenance & Fault FindingAppendix B SeaTalk and NMEA Data Appendix C List of AbbreviationsHow this Handbook is Organized Chapter 1 Overview1.1 Introduction General 1.2 FeaturesDisplay Display ModesDisplay Functions 1.3 The Plotter DisplayPlotter Functions GPS Data Pages 1.4 Operating ControlsMoving the Cursor Trackpad and CursorContext-Sensitive Cursor Control Dedicated KeysSoft Keys ALARMS SET UPPop-Up Menus Note If the key text is greyed out, it is not currently availableWAYPOINT LIST Database ListsPOSITION 348 mChapter 2 Getting Started 2.2 Power On/Off2.1 Introduction Conventions UsedGPS STATUS SD-FIX1.0 D-FIX STEER STARBOARDChanging the Lighting and Contrast Note Factory default settings are LIGHT OFF and CONTRAST 50%2.3 Controlling the Display Selecting the Display Mode5050000W Figure 2-5 Display Modes00106000W Chapter 2 Getting Started2.4 Plotter Display Control Functions Using FIND SHIPMoving Around the Plotter Screen Panning the DisplayChanging the Display Scale Changing the Display CenterCustomizing the Display Options Switching the Cursor Data Box On/offSwitching Grid On/off Simulator ModeRaynav 300 GPS Plotter 2-103.1 Introduction 3.2 Changing the Display ModeChapter 3 Operation Data Display Pages 0.55 nm 320 M050 M 12.0 kts0.55nm 320M050M 12.0kts01 h00 m 0.06 nmRNG 0.55 nm 133400RNG 0.55nm BRG 320MDEPTH 12.5 m SPEED 11ktsLOCK 323M AUTO0.05nm DEPTH 12.5MWIND APP WIND TRUEEnvironment Data Figure 3-11 Environment Data #1300T 0.05nm23.2nm CDI/BDI DataData Boxes 28.7nm 124T MANUAL104018 17kts 124T 0.05nmPOSITION TIMEData Log Introduction 3.3 Working with WaypointsWAYPOINT LIST Placing a WaypointPOSITION 348 m124 m NEW WAYPOINTRNG 12.6 nm Figure 3-19 New Waypoint Screen3-15 WPT POSITION LORAN TDsFigure 3-20 Waypoint Position Screen Loran TDs Figure 3-21 Select Chain/Slaves ScreenFigure 3-23 Waypoint Soft Keys Selecting a WaypointNote The ERASE WPT soft key is only available via the Waypoint List Waypoint Data DisplayEditing Waypoint Details D49091 Figure 3-25 Waypoint Symbol SelectionMoving a Waypoint Erasing a WaypointFigure 3-26 ST80 Navigator Keypad Using the ST60 or ST80 Navigator KeypadEditing Entries in the Waypoint, Route, or Track Lists Selecting an Entry in the Waypoint ListTo edit an item in a list using the Navigator Keypad 3.4 Working with Routes Creating a New Route Figure 3-27 Default Soft Keys TypicalWAYPOINTS NEW ROUTETo make a new route by placing waypoints using the cursor D4928-1 Figure 3-31 Make Route Soft KeysSAVE ROUTE Saving the Current RouteROUTE LIST Displaying Route InformationFull Route Details INFO FOR ROUTE - NEW ROUTE CLEAR Clearing the Current Route from the ScreenRoute Leg and Waypoint Information D4915-1 D4961-1Retrieve a Route from the Database Using the Route List to Erase or Name a RouteAdding/Removing Waypoints at the End of the Route Editing a RouteInserting a Waypoint into a Route i. Press REVERSE ROUTE Removing a Waypoint from within the RouteReversing the Route Note The soft keys differ if a follow or goto is already in progress 3.5 Following Routes and Going to WaypointsGoing To an Individual Target Point Follow a Route LOWING ROUTE. CANCEL ROUTE AND GOTO CURSOR?Note You cannot remove a waypoint from a route if it is the target Other Follow Route OptionsStop Follow or Stop Goto Restart Cross Track Error XTEJoining a Route Advancing to a WaypointTarget Point Arrival Displayed SeaTalk Waypoints 3.6 Transferring Waypoints and RoutesTransferring Database Lists Receiving Waypoints from Other EquipmentSending Waypoints to Other Equipment 3.7 Using TracksFigure 3-41 Track Interval Setting Guide Setting Up a TrackClearing the Current Track Saving and Naming the Current Track SmartRouteManaging Tracks Naming, Erasing and Showing a Track MOB DR 3.8 Man Overboard MOB0.33 nm 162 TExternal Alarms 3.9 Alarms & TimersALARMS SET UP Setting Alarms and TimersFigure 3-47 Alarms Set Up Menu 3.10 Cursor Echo Raynav 300 GPS Plotter 3-504.1 Introduction Chapter 4 Setting Up the GPS PlotterTrack, detailed in Using Tracks on page Figure 4-1 Set Up Soft Keys 4.2 Changing the Set Up ParametersTable 4-1 System Set Up Parameters 4.3 System Set Up ParametersChapter 4 Setting Up the GPS Plotter DefaultCursor Reference Bearing ModeTable 4-1 System Set Up Parameters Continued Cursor Readout Note The alarms continue to soundDay/Night HelpAuto Mode Menu Timeout PeriodAutopilot Pop Up UnitsDate and Time Settings NMEA OUT Set UpManual Mode Note The remote display must have SeaTalk Cursor Out enabledGPS SOG/COG Filter GPS SourceNMEA Input LanguageTable 4-2 Plotter Set Up Parameters 4.4 Plotter Set Up ParametersChart Orientation Default Waypoint Symbol Waypoint SymbolsWaypoint Numbers VectorsDatum Selection Position OffsetFix Mode 4.5 GPS Set UpGPS STATUS 1.0 D-FIXDIFFERENTIAL GPS SET UP D-GPS Set UpSignal Strength and Signal to Noise Ratio D-GPS ModeBeacon ID Beacon FrequencyDifferential Age Restart GPSRaynav 300 GPS Plotter 4-165.1 Introduction Chapter 5 InstallationEMC Installation Guidelines Figure 5-1 Typical Suppression Ferrites Suppression FerritesConnections to Other Equipment 5.2 Unpacking and Inspecting the Components System Parts and AccessoriesItems Missing? Registering this ProductSurface Mounting 5.3 GPS Antenna InstallationD47251 Top viewUnderside view Figure 5-3 Pole Mounting Arrangement Pole Mounting5.4 Plotter Installation Raynav 300 GPS Plotter Figure 5-4 Raynav 300 GPS Plotter DimensionsTrunnion yoke Mounting Note The gasket must be fitted to ensure EMC compliance Panel MountingFigure 5-5 Panel Mounting 5.5 Connecting to Other EquipmentIntroduction Connectors5.6 Cable Running This unit is not intended for use on positive ground vessels Antenna ConnectorPWR/NMEA Connector Color Table 5-2 Power/NMEA ConnectionsFunction SeaTalk Connector 5.7 System Check and Initial Switch OnSystem Check EMC ConformanceChecking the Plotter Operation Initial Switch OnSYSTEM SET UP MENU Raynav 300 GPS Plotter 5-166.1 Maintenance Chapter 6 Maintenance & Fault FindingEMC Servicing and Safety Guidelines Routine ChecksDisposal 6.2 Resetting the SystemNote The factory default settings are listed in Chapter 6.3 Problem SolvingRaynav 300 GPS Plotter Appendix A Technical Summary Appendix A Technical SummaryFeature DescriptionBuilt in Lithium battery giving ~5 years FeatureDescription From a PC serial port via the NMEA interAppendix B SeaTalk and NMEA Data Appendix B SeaTalk and NMEA DataData Received SourceData Output The following data, if available, are transmitted on the SeaTalk portSeaTalk NMEA OutAppendix C List of Abbreviations Appendix C List of AbbreviationsAbbreviation MeaningRaynav 300 GPS Plotter 3. LIMITED WARRANTY REMEDIES DISCLAIMER LIMITATION OF LIABILITY SiRF LICENSE AGREEMENT IMPORTANT - READ CAREFULLYPage GPS Antenna Mounting Template Installation TemplatesRaynav 300 Plotter Installation Templates Raynav 300 GPS Plotter Mounting TemplateCut out shaded area only 300/320 TemplateRaynav 300 GPS Plotter Index see also WAAS EMC see also WAAS Managing Page Page Page Limited Warranty Warranty CertificateInstalled Warranty Obtaining Warranty ServiceWarranty Limitations Sales & Order Services Factory Service CentersUnited States of America UK, Europe, Middle East, Far East