Schneider Electric iEM3100, iEM3300, iEM3200 Front panel display and meter setup, DOCA0005EN-04

Front panel display and meter setup			iEM3100 / iEM3200 / iEM3300 series user manual
Section	Parameter	Options	Description
			Select the tariff control mode:
			• Disable: the Multi Tariff function is disabled.
		Disable	• by Communication: the active tariff is control by communications. See
			the chapter for the applicable protocol for more information.
Multi Tariffs	Control Mode	by Communication	• by Digital Input: the digital input is associated with the multi-tariff
		by Digital Input	function. A signal to the digital input changes the active tariff.
			• by Internal Clock: the device clock controls the active tariff. If you set the
		by Internal Clock
			Control Mode to by Internal Clock, you must also configure the
			schedule. Set the time when each tariff period starts, using the 24 hour
			clock format (00:00 to 23:59). The start time of the next tariff is the end
			time of the current tariff. For example, T2 start equals the end of T1.
		Disable	Select whether or not the Overload Alarm is enabled:
Overload Alarm	Alarm		• Disable: the alarm is disabled.
		Enable
			• Enable: the alarm is enabled. If you enabled the Overload Alarm, you
			must also configure the Pick Up Value in kW from 1 - 9999999.
			Select how the digital output functions:
			• Disable: the digital output is disabled.
			• for Alarm: the digital output is associated with the overload alarm. The
		Disable	meter sends a pulse to the digital output port when the alarm is
Digital Output	DO Function	for Alarm	triggered.
			• for Pulse: The digital output is associated with energy pulsing. When
		for Pulse (kWh)
			this mode is selected, you must also configure the can select the energy
			parameter and the set the Pulse Constant (imp/kWh) and the Pulse
			Width (ms).
			NOTE: the iEM3175 and iEM3375 do not have a digital output.
			Select how the digital input functions:
			• Input status: the digital input records the status of the input, for example,
		Input Status	OF, SD of a circuit breaker.
		Tariff Control	• Input Metering: the digital input is associated with input metering. The
Digital Input	DI Function		meter counts and records the number of incoming pulses. If you set the
		Input Metering
			DI Function to Input Metering, you must also configure In. Pulse
		Partial Reset	Constant.
			• Tariff Control: the digital input is associated with the multi-tariff function.
			A signal to the digital input changes the active tariff.
			• Partial Reset: a signal to the digital input initiates a partial reset.
	Slave Address	1 - 247	Set the address for this device. The address must be unique for each
			device in a communications loop.
		19200	Select the speed for data transmission. The baud rate must be the same for
Communication	Baud Rate	38400
			all devices in a communications loop.
(iEM3155 / iEM3355)		9600
		Even	Select None if the parity bit is not used. The parity setting must be the same
	Parity	Odd	for all devices in a communications loop.
		None	NOTE: Number of stop bits = 1.
	Primary Addr.	0 - 255	Set the address for this device. The address must be unique for each
			device in a communications loop.
		2400
Communication		4800
(iEM3135 / iEM3335)	Baud Rate	9600	Select the speed for data transmission. The baud rate must be the same for
		300	all devices in a communications loop.
		600
		1200
	MAC Addr.	1 - 127	Set the address for this device. The address must be unique for each
			device in a communications loop.
		9600
Communication		19200	Select the speed for data transmission. The baud rate must be the same for
	Baud Rate	38400
(iEM3165 / iEM3365)			all devices in a communications loop.
		57600
		76800
	Device ID	0 - 4194303	Set the Device ID for this device. Make sure the Device ID is unique in your
			BACnet network.
Com.Protection	Com.Protection	Enable	Protects selected settings and resets from configuration via
		Disable	communications.
Contrast	Contrast	1-9	Increase or decrease the value to increase or decrease the display
			contrast.
Password	Password	0-9999	Sets the password for accessing the meter configuration screens and
			resets.
Reset Config	Reset Config	—	Settings are reset to their defaults, except for Password. Meter restarts.

44 DOCA0005EN-04