(Pg.No. 2)
L.
SS [READ-END]
READ-END

BASIC OPERATIONS

Entering a pause.

 

If you need to insert a

 

Using the document glass

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PAUSE

 

 

 

 

NEXT

pause between digits to

 

 

 

 

 

 

 

 

 

 

 

7

Press the [START] key ( ).

 

AX MEMORY:100%

 

access an outside line or

 

 

AD

dial an international

 

 

 

 

 

 

AUTO RECEPTION

 

 

 

 

 

 

B

number, touch the

 

 

 

The original is scanned

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[PAUSE] key in the upper

 

 

 

and the [READ-END] key

 

 

 

 

 

 

 

SUB A

right-hand corner of the

 

 

 

appears.

 

 

 

 

 

 

 

 

screen.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Each time you touch the [PAUSE] key, a hyphen ("-")

 

 

 

 

 

 

appears and a 2-second pause* is inserted.

 

 

 

 

 

 

After entering a number, you can also touch the

 

 

 

 

 

 

[PAUSE] key to enter a hyphen, and then enter

 

8

If you have another page to scan,

 

another number using the numeric keys or a rapid key.

 

 

 

 

change pages and then press the

 

This connects the numbers together (Chain dialing).

 

 

[START] key ( ).

 

 

 

2

*The duration of each pause can be changed with the

 

 

 

 

Repeat this sequence until all pages have been

key operator program. ("PAUSE TIME SETTING"

 

 

 

 

scanned. You can change the original size,

(p.97))

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

resolution, and exposure settings as needed for

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

each page.

 

 

 

Group keys cannot be used for chain

 

 

 

 

Note

 

 

If no action is taken for one minute (the [START]

 

 

dialing.

 

 

 

 

 

 

 

 

 

 

 

key ( ) is not pressed), scanning automatically

 

 

 

 

 

 

 

 

 

 

 

 

Using the RSPF

 

 

 

ends and the transmission job is stored.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

9

After the final page is scanned, touch

 

7 Press the [START] key ( ).

 

 

 

the [READ-END] key.

 

 

 

 

Scanning begins.

If a job is not in progress and the telephone line is

not being used, the destination is dialed

while the original is being scanned. (This is called "Quick on-line"; see page 14). If there is a

previously stored job or a job is in progress, or if the line is being used, all pages of the document are scanned into memory and stored as a transmission job. (This is called memory transmission: the destination is automatically called and the document transmitted after previously stored jobs are completed.)

If scanning is completed normally, a beep sounds to inform you that the transmission job is stored and "JOB STORED." appears in the message display.

A beep sounds to inform you that the transmission job is stored and "JOB STORED." appears in the message display.

(The destination is

automatically called and the document transmitted

after previously stored jobs are completed.) Open the RSPFand remove the document.

Canceling transmission

Note To cancel transmission while "SCANNING ORIGINAL" appears in the display or before the [READ-END] key is pressed, press the [CLEAR] key () or the [CLEAR ALL] key ( ). To cancel a transmission job that is already stored, press the [JOB STATUS] key and cancel the job as explained on page 24.

 

• If the machine sounds two beeps during or at the end of transmission and an error message

Caution

appears in the touch panel, refer to "WHEN AN ALARM SOUNDS AND A WARNING

 

 

MESSAGE IS DISPLAYED" (p.86) to fix the problem.

•If the power is turned off or there is an interruption in the power supply while an original is being scanned using the RSPF, scanning will stop and a misfeed will occur. After the power is restored, remove the misfed original as explained in "MISFEED REMOVAL" in the operation manual for copier.

13