Texas Instruments PCI7421, PCI7411, PCI7611, PCI7621 Secondary Status Register, Secondary status

4.14 Secondary Status Register

The secondary status register is compatible with the PCI-PCI bridge secondary status register. It indicates CardBus-related device information to the host system. This register is very similar to the PCI status register (PCI offset 06h, see Section 4.5), and status bits are cleared by a writing a 1. This register is not shared by the two socket functions, but is accessed on a per-socket basis. See Table 4−5 for a complete description of the register contents.

Bit

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

0

Name

Secondary status

Type

RC

RC

RC

RC

RC

R

R

RC

R

R

R

R

R

R

R

R

Default

0

0

0

0

0

0

1

0

0

0

0

0

0

0

0

0

Register:

Secondary status

Offset:

16h

Type:

Read-only, Read/Clear

Default:

0200h

Table 4−5. Secondary Status Register Description

BIT

SIGNAL

TYPE

FUNCTION

15 ‡

CBPARITY

RC

Detected parity error. This bit is set when a CardBus parity error is detected, either an address or data

parity error. Write a 1 to clear this bit.

14 ‡

CBSERR

RC

Signaled system error. This bit is set when

CSERR

is signaled by a CardBus card. The PCI7x21/PCI7x11

controller does not assert the CSERR signal. Write a 1 to clear this bit.

13 ‡

CBMABORT

RC

Received master abort. This bit is set when a cycle initiated by the PCI7x21/PCI7x11 controller on the

CardBus bus is terminated by a master abort. Write a 1 to clear this bit.

12 ‡

REC_CBTA

RC

Received target abort. This bit is set when a cycle initiated by the PCI7x21/PCI7x11 controller on the

CardBus bus is terminated by a target abort. Write a 1 to clear this bit.

11 ‡

SIG_CBTA

RC

Signaled target abort. This bit is set by the PCI7x21/PCI7x11 controller when it terminates a transaction

on the CardBus bus with a target abort. Write a 1 to clear this bit.

10−9

CB_SPEED

R

CDEVSEL timing. These bits encode the timing of

CDEVSEL

and are hardwired to 01b indicating that the

PCI7x21/PCI7x11 controller asserts this signal at a medium speed.

CardBus data parity error detected. Write a 1 to clear this bit.

0 = The conditions for setting this bit have not been met.

8 ‡

CB_DPAR

RC

1 = A data parity error occurred and the following conditions were met:

a. CPERR was asserted on the CardBus interface.

b. The PCI7x21/PCI7x11 controller was the bus master during the data parity error.

c. The parity error response enable bit (bit 0) is set in the bridge control register (PCI offset 3Eh,

see Section 4.25).

7

CBFBB_CAP

R

Fast

back-to-back capable.

The PCI7x21/PCI7x11 controller

cannot

accept

fast

back-to-back

transactions; therefore, this bit is hardwired to 0.

6

CB_UDF

R

User-definable

feature

support. The

PCI7x21/PCI7x11

controller does

not support

user-definable

features; therefore, this bit is hardwired to 0.

5

CB66MHZ

R

66-MHz capable. The PCI7x21/PCI7x11 CardBus interface operates at a maximum CCLK frequency of

33 MHz; therefore, this bit is hardwired to 0.

4−0

RSVD

R

These bits return 0s when read.

‡This bit is cleared only by the assertion of GRST.

4−9