Node Identification Register | Texas Instruments PCI7611, PCI7411

8.32 Node Identification Register

The node identification register contains the address of the node on which the OHCI-Lynxchip resides, and indicates the valid node number status. The 16-bit combination of the busNumber field (bits 15−6) and the NodeNumber field (bits 5−0) is referred to as the node ID. See Table 8−24 for a complete description of the register contents.

Bit	31	30	29	28	27	26	25		24	23		22	21	20	19	18	17	16

Name								Node identification

Type	RU	RU	R	R	RU	R	R		R	R		R	R	R	R	R	R	R

Default	0	0	0	0	0	0	0		0	0		0	0	0	0	0	0	0

Bit	15		14	13	12		11	10	9		8	7		6	5	4	3	2	1	0

Name										Node identification

Type	RWU		RWU	RWU	RWU		RWU	RWU	RWU		RWU	RWU		RWU	RU	RU	RU	RU	RU	RU

Default	1		1	1	1		1	1	1		1	1		1	X	X	X	X	X	X

	Register:			Node identification
	Offset:			E8h
	Type:			Read/Write/Update, Read/Update, Read-only
	Default:			0000 FFXXh

Table 8−24. Node Identification Register Description

BIT	FIELD NAME	TYPE	DESCRIPTION

31	iDValid	RU	Bit 31 indicates whether or not the PCI7x21/PCI7x11 controller has a valid node number. It is cleared
			when a 1394 bus reset is detected and set to 1 when the PCI7x21/PCI7x11 controller receives a new
			node number from its PHY layer.

30	root	RU	Bit 30 is set to 1 during the bus reset process if the attached PHY layer is root.

29−28	RSVD	R	Reserved. Bits 29 and 28 return 0s when read.

27	CPS	RU	Bit 27 is set to 1 if the PHY layer is reporting that cable power status is OK.

26−16	RSVD	R	Reserved. Bits 26−16 return 0s when read.

15−6	busNumber	RWU	This field identifies the specific 1394 bus the PCI7x21/PCI7x11 controller belongs to when multiple
			1394-compatible buses are connected via a bridge. The default value for this field is all 1s.

5−0	NodeNumber	RU	This field is the physical node number established by the PHY layer during self-identification. It is
			automatically set to the value received from the PHY layer after the self-identification phase. If the PHY
			layer sets the nodeNumber to 63, then software must not set bit 15 (run) in the asynchronous context
			control register (see Section 8.40) for either of the AT DMA contexts.

8−29

Image 209

Texas Instruments PCI7611, PCI7411, PCI7621, PCI7421 Node identification, 24. Node Identification Register Description

Contents

Data Manual Important Notice Contents −10 PC Card Controller Programming Model −1 ExCA Compatibility Registers Functions 0 and 1 −1 Vii Ohci Controller Programming Model −1Ohci Registers −1 Viii PHY Register Configuration 10−1TI Extension Registers −1 SD Host Controller Programming Model −1 Flash Media Controller Programming Model −1 Smart Card Controller Programming Model −1 Mechanical Information 15−1 Electrical Characteristics −1 Xii List of Illustrations Xiii List of Tables Xiv Functions 0 and 1 PCI Configuration Register Map Title −13 Xvi Xvii Xviii 1 PCI7621 Controller Controller Functional Description 3 PCI7611 Controller 2 PCI7421 Controller Power Switch Interface PCI Bus Power Management4 PCI7411 Controller Multifunctional Terminals PCI Bus Interface Specification for PCI-to-CardBus Bridges Features Related Documents PCI Local Bus Specification Revision Trademarks Ordering Information Terms and Definitions−1. Terms and Definitions Term DefinitionsPage Terminal Descriptions −2. PCI7421 GHK/ZHK-Package Terminal Diagram −3. PCI7611 GHK/ZHK-Package Terminal Diagram −4. PCI7411 GHK/ZHK-Package Terminal Diagram Terminal Signal Name Number −1. Signal Names by GHK Terminal Number ACC/BE2 BresetVCC VCC Acperr BCC/BE0 BCE1 ScclkSCVCC5V Latch GNT Perr Grst FrameRIOUT/PME Vsspll Signal Name Terminal Number −2. CardBus PC Card Signal Names Sorted Alphabetically PC2TEST3 SdcmdPerr Trdy GND Prst GND Signal Terminal Signal Name Number −3 -Bit PC Card Signal Names Sorted Alphabetically −12 −13 Detailed Terminal Descriptions −14 −4. Power Supply Terminals −15 −5. PC Card Power Switch Terminals−6. PCI System Terminals −16 −7. PCI Address and Data Terminals −17 −8. PCI Interface Control Terminals −18 −9. Multifunction and Miscellaneous Terminals −10 -Bit PC Card Address and Data Terminals Stschg −11 -Bit PC Card Interface Control Terminals AOE PCIO3 Vccb −12. CardBus PC Card Interface System Terminals BCAD0 −13. CardBus PC Card Address and Data Terminals BCCD2 −14. CardBus PC Card Interface Control Terminals Cstop −26 −15. Ieee 1394 Physical Layer Terminals −27 −16. SD/MMC Terminals−17. Memory Stick/PRO Terminals −28 −18. Smart Media/XD Terminals −19. Smart Card Terminals † −30 Eeprom Power Supply SequencingSD/MMC MS/MSPRO SD/MMC Clamping Voltages I/O CharacteristicsPeripheral Component Interconnect PCI Interface 1 1394 PCI Bus Master VCC Grst Prst Pclk Device ResetsSerial Eeprom I2C Bus ROM A1 SCL A2 SDA VCC Functions 0 and 1 CardBus Subsystem Identification Function 2 Ohci 1394 Subsystem Identification PC Card ApplicationsFunction 3 Flash Media Subsystem Identification Function 4 SD Host Subsystem Identification UltraMedia Card Detection PC Card Insertion/Removal and RecognitionLow Voltage CardBus Card Detection −2. PC Card-Card Detect and Voltage Sense Connections Flash Media Card DetectionCD2//CCD2 CD1//CCD1 VS2//CVS2 VS1//CVS1 VCC VPP/VCORE −3. TPS2228 Control Logic-xVPP/VCORE Internal Ring Oscillator−4. TPS2228 Control Logic-xVCC −5. TPS2226 Control Logic-xVPP Integrated Pullup Resistors for PC Card Interface LED Socket Activity IndicatorsSpkrout and Caudpwm Usage Spkrout Binaryspkr 11 48-MHz Clock Requirements CardBus Socket Registers−7. CardBus Socket Registers LED Serial Eeprom Interface Accessing Serial-Bus Devices Through SoftwareSerial-Bus Interface Implementation Serial-Bus Interface Protocol −8. Serial-Bus Protocol Acknowledge −7. Serial-Bus Start/Stop Conditions and Bit Transfers −10. Serial-Bus Protocol-Byte Read Serial-Bus Eeprom Application GPE −9. Eeprom Loading MapSerial ROM Byte Description Offset PCI 2Ch, subsystem vendor ID, byte LinkEnh HCControl.Program Phy EnablePCI 2Dh, subsystem vendor ID, byte PCI 2Eh, subsystem ID, byte Programmable Interrupt Subsystem Card Type Event Mask Flag PC Card Functional and Card Status Change Interrupts−10. Interrupt Mask and Flag Registers −11. PC Card Interrupt Events and Description Card Type Event Signal DescriptionInterrupt Masks and Flags Using Parallel PCI Interrupts Using Parallel IRQ Interrupts Using Serialized Irqser Interrupts Power Management OverviewSMI Support in the PCI7x21/PCI7x11 Controller −12. Interrupt Pin Register Cross Reference 1 1394 Power Management Function Integrated Low-Dropout Voltage Regulator LDO-VR CardBus PC Card Power ManagementCardBus Functions 0 and 1 Clock Run Protocol Supply VCC Vren Vrport Suspend Mode 5 16-Bit PC Card Power ManagementRequirements for Suspend Mode Reset GNT Suspend Pclk Rienb Riout Ring IndicateCstsmask CSC Ringen RI Cdresume Power-management control/status CSR PCI Power Management−15. Power-Management Registers −16. Function 2 Power-Management Registers CardBus Bridge Power Management−17. Function 3 Power-Management Registers −18. Function 4 Power-Management Registers Acpi Support Master List of PME Context Bits and Global Reset-Only Bits −28 −29 PHY Port Cable Connection Ieee 1394 Application Information −31 Crystal Selection −32 Bus ResetCphy + CBD −33 −34 −1. Bit Field Access Tag Descriptions PCI Configuration Register Map Functions 0−2. Functions 0 and 1 PCI Configuration Register Map Access TAG Name Meaning Vendor ID Vendor ID Register Device ID Device ID-Smart Card enabledDevice ID Register Functions 0 Command Command Register−3. Command Register Description BIT Signal Type Function −4. Status Register Description Status RegisterStatus Cache Line Size Register Revision ID RegisterClass Code Register Register Latency timer Latency Timer RegisterHeader Type Register Bist Register Capability Pointer Register CardBus Socket Registers/ExCA Base Address RegisterCardBus socket registers/ExCA base address Register Capability pointer −5. Secondary Status Register Description Secondary Status RegisterSecondary status Subordinate Bus Number Register PCI Bus Number RegisterCardBus Bus Number Register Register CardBus latency timer CardBus Latency Timer RegisterCardBus Memory Base Registers 0 Memory base registers 0 CardBus I/O Base Registers 0 CardBus Memory Limit Registers 0Memory limit registers 0 Base registers 0 Interrupt Line Register CardBus I/O Limit Registers 0Limit registers 0 Register Interrupt line Interrupt pin − PCI function Interrupt Pin Register Interrupt pin Bridge Control Register−6. Interrupt Pin Register Cross Reference Bridge control Subsystem vendor ID Subsystem Vendor ID Register PC Card 16-Bit I/F Legacy-Mode Base-Address Register Subsystem ID RegisterSubsystem ID PC Card 16-bit I/F legacy-mode base-address −8. System Control Register Description System Control RegisterSystem control −8 . System Control Register Description Register Mccd debounce Mccd Debounce Register General control General Control RegisterGeneral control −9. General Control Register Description −10. General-Purpose Event Status Register Description General-Purpose Event Status RegisterGeneral-purpose event status General-Purpose Input Register General-Purpose Event Enable Register −13. General-Purpose Output Register Description General-Purpose Output RegisterGeneral-purpose output −14. Multifunction Routing Status Register Description Multifunction Routing Status RegisterMultifunction routing status −15. Retry Status Register Description Retry Status RegisterRetry status −16. Card Control Register Description Card Control RegisterCard control −17. Device Control Register Description Device Control RegisterDevice control −18. Diagnostic Register Description Diagnostic RegisterDiagnostic Next Item Pointer Register Capability ID RegisterRegister Capability ID Register Next item pointer −19. Power Management Capabilities Register Description Power Management Capabilities RegisterPower management capabilities −20. Power Management Control/Status Register Description Power Management Control/Status RegisterPower management control/status Power management control/status bridge support extensions Power-Management Data RegisterPower-management data Bpccen Serial Bus Index Register Serial Bus Data RegisterSerial bus data −22. Serial Bus Data Register Description Register Serial bus slave address Serial Bus Slave Address Register−24. Serial Bus Slave Address Register Description Rwcmd −25. Serial Bus Control/Status Register Description Serial Bus Control/Status RegisterSerial bus control/status −38 ExCA Compatibility Registers Functions 0 −1. ExCA Register Access Through I/O −1. ExCA Registers and Offsets Exca Register Name PCI Memory Address Exca Offset Offset HEX ExCA identification and revision ExCA Identification and Revision Register−2. ExCA Identification and Revision Register Description Iftype −3. ExCA Interface Status Register Description ExCA Interface Status RegisterExCA interface status −4. ExCA Power Control Register Description-82365SL Support ExCA Power Control RegisterExCA power control −6. ExCA Interrupt and General Control Register Description ExCA Interrupt and General Control RegisterRegister ExCA interrupt and general control −7. ExCA Card Status-Change Register Description ExCA Card Status-Change RegisterExCA card status-change Register ExCA card status-change interrupt configuration ExCA Card Status-Change Interrupt Configuration Register −9. ExCA Address Window Enable Register Description ExCA Address Window Enable RegisterExCA address window enable −10. ExCA I/O Window Control Register Description ExCA I/O Window Control RegisterExCA I/O window control ExCA I/O Windows 0 and 1 Start-Address High-Byte Registers ExCA I/O Windows 0 and 1 Start-Address Low-Byte Registers ExCA I/O Windows 0 and 1 End-Address High-Byte Registers ExCA I/O Windows 0 and 1 End-Address Low-Byte Registers ExCA Memory Windows 0−4 Start-Address Low-Byte Registers ExCA Memory Windows 0−4 Start-Address High-Byte Registers ExCA Memory Windows 0−4 End-Address Low-Byte Registers ExCA Memory Windows 0−4 End-Address High-Byte Registers ExCA Memory Windows 0−4 Offset-Address Low-Byte Registers ExCA Memory Windows 0−4 Offset-Address High-Byte Registers ExCA card detect and general control ExCA Card Detect and General Control Register −15. ExCA Global Control Register Description ExCA Global Control RegisterExCA global control ExCA I/O Windows 0 and 1 Offset-Address High-Byte Registers ExCA I/O Windows 0 and 1 Offset-Address Low-Byte Registers Register ExCA memory windows 0−4 ExCA Memory Windows 0−4 Page Registers CardBus Socket Registers Functions 0 −2. Socket Event Register Description Socket Event RegisterSocket event −3. Socket Mask Register Description Socket Mask RegisterSocket mask −4. Socket Present State Register Description Socket Present State RegisterSocket present state Socket force event Socket Force Event Register −5. Socket Force Event Register Description −6. Socket Control Register Description Socket Control RegisterSocket control −7. Socket Power Management Register Description Socket Power Management RegisterSocket power management Pmcsrbse −1. Function 2 Configuration Register Map Device ID Register BIT Field Name Type Description −2. Command Register Description −3. Status Register Description Latency timer and class cache line size Latency Timer and Class Cache Line Size RegisterClass Code and Revision ID Register Class code and revision ID Ohci Base Address Register Header Type and Bist Register −8. TI Base Address Register Description TI Extension Base Address RegisterTI extension base address CardBus CIS Pointer Register CardBus CIS Base Address RegisterCardBus CIS base address −9. CardBus CIS Base Address Register Description Power management capabilities pointer Power Management Capabilities Pointer RegisterSubsystem Identification Register Subsystem identification Register Interrupt pin −11. Interrupt Line Register DescriptionBIT Field Name Type Description Intrline 01h Inta 02h Intb 03h Intc Bits Intsel Ohci Control Register Minimum Grant and Maximum Latency Register Capability ID and next item pointer Capability ID and Next Item Pointer RegistersNextitem Capabilityid −16. Power Management Capabilities Register Description Power Management Extension Registers Power Management Control and Status RegisterPower management control and status Power management extension PCI PHY control PCI PHY Control Register−19. PCI PHY Control Register Description Cnaout −20. PCI Miscellaneous Configuration Register Description PCI Miscellaneous Configuration RegisterPCI miscellaneous configuration −21. Link Enhancement Control Register Description Link Enhancement Control RegisterLink enhancement control Subsystem access Subsystem Access Register−22. Subsystem Access Register Description Subdevid −23. Gpio Control Register Description Gpio Control RegisterGpio control GPIOENB1 GPIO1 Disablebmc GPIO0GPIODATA1 = GPIO0 Guid ROM Guidrom −1. Ohci Register MapDMA Context Register Name Abbreviation Offset Isochronous receive interrupt mask IsoRecvIntMaskSet IsoRecvIntEventClearPhysicalRequestFilterHiClear Physical request filter low PhysicalRequestFilterLoSet Asynchronous context control ContextControlSet Isochronous receive context commandContextControlClear Request Transmit Reserved −2. Ohci Version Register Description Ohci Version RegisterOhci version −3. Guid ROM Register Description Guid ROM RegisterGuid ROM RSU CSR Data Register Asynchronous Transmit Retries RegisterAsynchronous transmit retries −4. Asynchronous Transmit Retries Register Description CSR Control Register CSR Compare RegisterCSR compare CSR control Configuration ROM header Configuration ROM Header Register−6. Configuration ROM Header Register Description Bus Identification Register −7. Bus Options Register Description Bus Options RegisterBus options Guid Low Register Guid High RegisterGuid high Guid low Posted Write Address Low Register Configuration ROM Mapping Register −10. Posted Write Address High Register Description Posted Write Address High RegisterPosted write address high Host controller control Host Controller Control Register−11. Host Controller Control Register Description RSU RSC Rscu LPS RSC Self-ID Buffer Pointer RegisterSelf-ID buffer pointer −12. Self-ID Count Register Description Self-ID Count RegisterSelf-ID count Isochronous receive channel mask high Isochronous Receive Channel Mask High Register Isochronous receive channel mask low Isochronous Receive Channel Mask Low Register Interrupt event Interrupt Event Register−15. Interrupt Event Register Description RSC Rscu Arrq Rscu Arrs Rscu Interrupt Mask Register MasterIntEnableInterrupt mask −16. Interrupt Mask Register Description Generation Arrs RSCArrq RSC Isochronous transmit interrupt event Isochronous Transmit Interrupt Event Register Isochronous transmit interrupt mask Isochronous Transmit Interrupt Mask Register Isochronous receive interrupt event Reserved. Bits 31−4 return 0s when readIsochronous Receive Interrupt Event Register Initial Bandwidth Available Register Isochronous Receive Interrupt Mask RegisterIsochronous receive interrupt mask Initial bandwidth available Initial Channels Available Low Register Initial Channels Available High Register Fairness control Fairness Control Register−22. Fairness Control Register Description Value for this field is 00h −23. Link Control Register Description Link Control RegisterLink control −24. Node Identification Register Description Node Identification RegisterNode identification −25. PHY Control Register Description PHY Layer Control RegisterPHY layer control −26. Isochronous Cycle Timer Register Description Isochronous Cycle Timer RegisterIsochronous cycle timer −27. Asynchronous Request Filter High Register Description Asynchronous Request Filter High RegisterAsynchronous request filter high From that node are accepted −28. Asynchronous Request Filter Low Register Description Asynchronous Request Filter Low RegisterAsynchronous request filter low Physical request filter high Physical Request Filter High Register−29. Physical Request Filter High Register Description PhysReqAllBusses That node are handled through the physical request context Physical Upper Bound Register Optional Register Physical Request Filter Low RegisterPhysical request filter low −30. Physical Request Filter Low Register Description Asynchronous context control Asynchronous Context Control Register−31. Asynchronous Context Control Register Description Rscu RSU DescriptorAddress Asynchronous Context Command Pointer RegisterAsynchronous context command pointer RSC RSU Isochronous Transmit Context Control RegisterIsochronous transmit context control Isochronous transmit context command pointer Isochronous Transmit Context Command Pointer RegisterIsochronous Receive Context Control Register Isochronous receive context control Not be changed while bit 10 active or bit 15 run is set to When software clears bit 15 runMultiChanMode Context match register see .46 is ignored Isochronous receive context command pointer Isochronous Receive Context Command Pointer RegisterIsochronous receive context command pointer −43 −35. Isochronous Receive Context Match Register Description Isochronous Receive Context Match RegisterIsochronous receive context match −1. TI Extension Register Map DV and MPEG2 Timestamp EnhancementsLink Enhancement Control Set Link Enhancement Control Clear A8Ch Isochronous receive digital video enhancements Isochronous Receive Digital Video EnhancementsIsochronous Receive Digital Video Enhancements Register 420h/424h see .44 is cleared to Reserved. Bits 7 and 6 return 0s when readCIPStrip1 Ohci offset 420h/424h see .44 is cleared to Link Enhancement Register Reserved. Bit 11 returns 0 when read 10 ‡Link enhancement −3. Link Enhancement Register Description −4. Timestamp Offset Register Description Timestamp Offset RegisterTimestamp offset Page Base Registers −1. Base Register ConfigurationAddress BIT Position RHB IBR RHB −2. Base Register Field DescriptionsField Size Type Description LLC to service the interrupt Long bus reset being performedTimeout Is unaffected by bus reset Port Status Register −3. Page 0 Port Status Register Configuration−4. Page 0 Port Status Register Field Descriptions BIT Position Address Hardware reset and is unaffected by bus reset −5. Page 1 Vendor ID Register ConfigurationVendor Identification Register −6. Page 1 Vendor ID Register Field Descriptions Vendor-Dependent Register −7. Page 7 Vendor-Dependent Register Configuration−8. Page 7 Vendor-Dependent Register Field Descriptions NPA −9. Power Class Descriptions Power-Class ProgrammingNode does not need power and does not repeat power PC0-PC2 Description 10−8 Flash Media Controller Programming Model −1. Function 3 Configuration Register Map 11−2 Stepenb Pcispeed Devsel Is deasserted Programming interface. This field returns 00h when readStorage controller −7. Flash Media Base Address Register Description Flash Media Base Address RegisterFlash media base address Capabilities Pointer Register Subsystem Vendor Identification RegisterSubsystem vendor identification Capabilities pointer 11−8 −8. PCI Interrupt Pin RegisterIntsel Bits Useinta Intpin Maximum Latency Register Minimum Grant Register This field returns 00h when read −12. Power Management Capabilities Register Description Pmestat RCU Power Management Bridge Support Extension RegisterPmeen PME Rsvd −14. General Control Register Power Management Data RegisterPower management data Register at PCI offset 2Ch 11−14 −15. Subsystem Access Register DescriptionSubsystemVendorID Diagnostic −16. Diagnostic Register DescriptionTbdctrl Plln 11−16 Maximum current −1. Function 4 Configuration Register MapSlot information 12−2 Bit 5 returns 0 when read Therefore, bit 9 returns 0 when readTransactions therefore, bit 4 returns 0 when read Bit 3 returns 0 when read Syserr RCU 12−5 PeripheralDMA capabilities 12−6 Memory-read line, and memory-read multiple transactionsRead SD host base address SD Host Base Address Register−7. SD host Base Address Register Description Type 12−8 12.12 Interrupt Line Register Space see Section 12−9 Register Maximum latency Slot Information Register−11. Maximum Latency Register Description Numberslots 12−11 Driver is able to use it −13. Power Management Capabilities Register DescriptionController to generate PME Revision 12−12 Enable. Enables Signaling Power management bridge support extensionRegister 12−13 01 = Intb 10 = Intc 11 = Intd −15. General Control RegisterDmaen Dmasupport bit of each SD host socket is −17. Diagnostic Register Description −16. Subsystem Access Register DescriptionReserved. Bits 31−17 return 0s when read Register at PCI offset 2Ch Slot 2 3.3-V Maximum Current Register Slot 0 3.3-V Maximum Current RegisterSlot 1 3.3-V Maximum Current Register Slot 5 3.3-V Maximum Current Register Slot 3 3.3-V Maximum Current RegisterSlot 4 3.3-V Maximum Current Register 12−18 60h−FCh −1. Function 5 Configuration Register Map1Ch−28h 13−2 Seren Intdis Tabtsig RCU Is enabled and the Smart Card controller hasIntstat 13−4 Offset 08h Type Read-only Default 0780 0000h Smart Card base address register Smart Card Base Address RegisterCard is a multifunction device Smart Card base address register 13−7 Smart Card Base Address Register 1−4Smart Card base address register 1−4 13−8 13.13 Interrupt Line Register Space see Section 13−9 −7. PCI Interrupt Pin Register−8. Minimum Grant Register Description 13−10 −9. Maximum Latency Register Description PMED3HOT −11. Power Management Capabilities Register DescriptionPMED2 PMED1 PMED0 D2SUPPORT 13−12 PME Grst RsvdDstate Pin = 01 = Intb pin = 10 = Intc pin = 11 = Intd pin = Gated to reduce power consumption−13. General Control Register Class Code Alias Register Subsystem ID Alias RegisterSubsystem ID alias −14. Subsystem ID Alias Register Description Smart Card configuration Smart Card Configuration 1 RegisterSmart Card configuration 13−15 −15. Smart Card Configuration 1 Register Description −16. Smart Card Configuration 2 Register Description Smart Card Configuration 2 RegisterPwrupdelay Reserved. Bits 7−0 return 0s when read 13−17 13−18 Recommended Operating Conditions see Note Absolute Maximum Ratings Over Operating Temperature Ranges†Operation MIN NOM MAX Unit Avdd VCC VDPLL15 VDPLL33 Vccp Recommended Operating Conditions TJ# Parameter Terminals Operation Test Conditions MIN MAX Unit 14.4.2 Driver 14.4.1 Device14.4.3 Receiver Parameter Test Condition MIN MAX Unit Operating, Timing, and Switching Characteristics Switching Characteristics for PHY Port InterfaceParameter Alternate Test Conditions MIN MAX Unit Parameter Test Conditions MIN TYP MAX Unit Mechanical Information 15−2 Package Option Addendum