Adjustment | Toshiba B-570 specs

2. MAJOR UNIT REPLACEMENT

EM18-33010A (Revision Date Sep. 29, ’95)

2.10 REPLACING THE PINCH ROLLER SHAFT ASS’Y

■Adjustment

1.Install the pinch roller unit so it parallels the base. If it does not, change the engaging position of the pinch roller belt and the pulley.

Pinch Roller Belt

Pinch Roller

Unit

Pulley

Base

Fig. 2-24

2.Attach the jig to the platen, feed roller and pinch roller shaft as shown in the figure below. Then attach the pinch roller cover to the pinch roller frame with the three B-4x12 screws. Then secure the pinch roller frame with the three B-4x12 screws.

Pinch Roller Cover

B-4x12 (6 screws)

Jig

Fig. 2-25

NOTES:1. Replace the platen and the feed roller prior to attaching the jig.

2.Attach the jig while the pinch roller frame is tentatively attached to the main frame with the B-4x12 screws. Secure the pinch roller cover to the pinch roller frame with the three B-4x12 screws, then tighten the other side of the screws.

3.The flat top of the pinch roller frame must be installed in parallel to bosses on the printer frame.

Check

1Check if excessive load is applied to the jig after the above NOTE 2.

(For example, check if the pinch roller frame moves when the jig is removed.)

2Check that there is no gap caused by a slant shaft between the pinch roller and the feed roller when the pinch roller is lowered.

2-15

Image 18

Toshiba B-570 manual Adjustment

Contents

Series Table of Contents Procedure Checks Major Unit Replacement Disconnect power cord before replacing important parts Replacing the PS UNIT, I/F PC Board and CPU PC Board An oscilloscope Turn the power off and mount the left side Cover and top cover Replacing the Stepping Motor Replacing the Ribbon Motors Replacing the TAKE-UP Motor Replacing the Solenoid Head Up Link Solenoid Spring Pin Replacing the Print Head Old type print head Adjusting the print head position New type print head Replacing the Platen and Feed Roller Replacing the Platen and Feed Roller Replacing the Paper Sensor Replacing the Ribbon Back Tension Block Replacing the Pinch Roller Shaft ASS’Y Adjustment Correcting Skew Printing Installation Procedure for the Optional Equipment High Speed PC Interface Board B-4800-PC-QM Installation Procedure for the Optional Equipment Cutter Module B-4205-QM EM18-33010A SVO7A1003 Nov ’97 Adjusting the Cutter Guide Plates Mount the cutter cover with the two screwsRemoved Parts ’ty/Unit Front plate Memory Module Expansion memory and drawing size Fanfold Paper Guide Module B-4905-FF-QM Cutter Drive Cutter Mode Mechanism Description Harness Wiring Dirty print head Clean the print head Toshiba TECFasten the head lever completely Refer to page 2-3 to adjust Sensor Setting Mode Parameter Setting ModeTest Print Mode RAM Clear Mode DIAG. Test Operation Outline of the DIAG. Test Operation L I N E Press the Pause key. See NoteU S E B B O N Self Test ModeMaintenance Counter Printing I N T E N a N C E C O U N T E R Sample Print Print Condition ∙ Preset count ∙ Print speed Parameters Trans Automatic Diagnostic Printing B B O N T R a N S M I S S I V EPress the Pause key On .2.3 Head Broken Element Check PROGRAM/MASK ROM Check Print Condition ∙ Preset count ∙ Print speedSample Print Kanji ROM Check Eeprom Check Dram CheckFlash Memory Card Check Sensor 1 Check Non-transmissive Print status content description of each sensor/switchLabel is removed Ribbon end sensor With ribbon Ribbon end Connector FCN-781P024-G/P DIP SW CheckEXP. I/O Check Press the Pause key twice Press the Feed key twice R M a L E N D A D ErrorHead Broken Element Check E R M a L H E a D C H E C K Parameter Setting Mode Press the Pause key Parameter Setting Mode Table Feed Length Fine Adjustment Press the Feed keyE D a D J U S T 2 Cut/Strip Position Fine Adjustment Press the Pause key twiceT a D J U S T Press the Pause key three times Back Feed Length Fine AdjustmentAt the same time On Section Axis fine adjustment Press the Feed key Press the Pause key Feed Length Fine Adjustment Example Cut Position Fine Adjustment Example Are received When using a label with a length of less than 38 mmCase Condition Label pitch Strip Position Fine Adjustment Example Back Feed Length Fine Adjustment Example Press the Pause key four times Axis Fine AdjustmentPress the Pause key On Section Print tone fine adjustment D J U S T Axis Fine Adjustment Example Print Tone Fine Adjustment Thermal transfer printing fine adjustmentThermal direct printing fine adjustment N T code Character Code SelectionPress the Pause key seven times At the same time On Section Font zero selection Font Zero Selection R O F O N TFeed key or Restart Control Code Selection Code Press the Pause key CodeM a N U a LN T R O L Restart ∙ Transmissive ribbon Ribbon Type SelectionPress the Pause key ten times Select either ribbon type with Ribbon Motor Drive Voltage Fine Adjustment Press the Pause key eleven times Strip Wait Status Setting A T U S P E Stacker Selection Press the Pause key fourteen timesA C K E R S Y S T E M O F F Threshold Manual Fine Adjustment for the Black Mark Sensor R E S H O L D R Threshold Manual Fine Adjustment for the Feed Gap Sensor Press the Pause key sixteen timesR E S H O L D T How To Calculate Theshold Fine Adjustment Value Case When using labels transmissive sensor When using perforated labels transmissive sensorWhen using labels with black marks reflective sensor N J I code Kanji Code SelectionPress the Pause key 17 times Select either code with R O codeB O H Euro Font Code SelectionPress the Pause key 18 times Select the Euro font code with the Feed key or RTS/CTS Transmission Control Mode SelectionDTR/DSR Restart key at Reset Selection when the Input Prime Signal is on Press the Pause key 20 timesP U T P R I M EO N I N T C O N D I T I O N Test Print ModeNormal Test Print Pause key I N T S P E E D N S O R T R a N S M I S S I V E B E L L E N G T H P E R F E E DFeed key or Restart key From B of the preceding Test Print Sample ∙ Print Tone Fine Adjustment Value + Process Test Print From B of the next Press the Pause key Bar code are printed on 5 labels Sensor Setting Mode Thermistor CheckPress the Feed key three times Black Mark Sensor Adjustment Press the Feed key Press the Pause key twice Feed Gap Sensor Adjustment Paper End Setting for Black Mark Sensor Feed key Former value is displayed Paper End Setting for Feed Gap Sensor Indicates setting complete. Press the Pause key. See NotePress the Pause key five times RAM Clear Mode RAM Clear Mode Table OFF TypeB0H I N T E C O U N T E R C L E a R Maintenance Counter ClearR a M C L E a R M P L E T E Parameter Clear R a M E T E R C L E a R IBM PC/AT SetupFloppy Disk SW# Down Load Procedure DD-MM-YYYY Error Code ROM