Maintenance Counter Clear, R a M C L E a R | Toshiba B-570 instruction

6.DIAG. TEST OPERATION

6.6.1Maintenance Counter Clear

EM18-33010A

6.6. RAM CLEAR MODE

Power off

Turn on the power while holding down the [FEED] key and [PAUSE] key.

< 1 > D I A G N O S T I C

V 1 . O A

Press the [FEED] key four times.

< 5 > R A M C L E A R

Press the [PAUSE] key. Press the [PAUSE] key.

N O R A M C L E A R

Press the [FEED] key and [RESTART] key at the same time.

Press the [FEED] key.

(or press the [RESTART] key twice.)

M A I N T E C O U N T E R C L E A R

Press the [PAUSE] key.

C O M P L E T E

Turn off the power (See NOTE.)

NOTE: Confirm that “COMPLETE” is displayed, then turn the power off.

6-55

Image 86

Toshiba B-570 manual Maintenance Counter Clear, R a M C L E a R, I N T E C O U N T E R C L E a R, M P L E T E

Contents

Series Table of Contents Procedure Checks Major Unit Replacement Disconnect power cord before replacing important parts Replacing the PS UNIT, I/F PC Board and CPU PC Board An oscilloscope Turn the power off and mount the left side Cover and top cover Replacing the Stepping Motor Replacing the Ribbon Motors Replacing the TAKE-UP Motor Replacing the Solenoid Head Up Link Solenoid Spring Pin Replacing the Print Head Old type print head Adjusting the print head position New type print head Replacing the Platen and Feed Roller Replacing the Platen and Feed Roller Replacing the Paper Sensor Replacing the Ribbon Back Tension Block Replacing the Pinch Roller Shaft ASS’Y Adjustment Correcting Skew Printing Installation Procedure for the Optional Equipment High Speed PC Interface Board B-4800-PC-QM Installation Procedure for the Optional Equipment Cutter Module B-4205-QM EM18-33010A SVO7A1003 Nov ’97 Removed Parts ’ty/Unit Front plate Adjusting the Cutter Guide PlatesMount the cutter cover with the two screws Memory Module Expansion memory and drawing size Fanfold Paper Guide Module B-4905-FF-QM Cutter Drive Cutter Mode Mechanism Description Harness Wiring Fasten the head lever completely Dirty print head Clean the print headToshiba TEC Refer to page 2-3 to adjust Sensor Setting Mode Parameter Setting ModeTest Print Mode RAM Clear Mode DIAG. Test Operation Outline of the DIAG. Test Operation U S E L I N EPress the Pause key. See Note B B O N Self Test ModeMaintenance Counter Printing I N T E N a N C E C O U N T E R Sample Print Print Condition ∙ Preset count ∙ Print speed Parameters Trans Press the Pause key On .2.3 Head Broken Element Check Automatic Diagnostic PrintingB B O N T R a N S M I S S I V E PROGRAM/MASK ROM Check Print Condition ∙ Preset count ∙ Print speedSample Print Kanji ROM Check Flash Memory Card Check Eeprom CheckDram Check Sensor 1 Check Non-transmissive Print status content description of each sensor/switchLabel is removed Ribbon end sensor With ribbon Ribbon end EXP. I/O Check Connector FCN-781P024-G/PDIP SW Check Press the Pause key twice Press the Feed key twice R M a L E N D A D ErrorHead Broken Element Check E R M a L H E a D C H E C K Parameter Setting Mode Press the Pause key Parameter Setting Mode Table E D a D J U S T Feed Length Fine AdjustmentPress the Feed key T a D J U S T 2 Cut/Strip Position Fine AdjustmentPress the Pause key twice Press the Pause key three times Back Feed Length Fine AdjustmentAt the same time On Section Axis fine adjustment Press the Feed key Press the Pause key Feed Length Fine Adjustment Example Cut Position Fine Adjustment Example Are received When using a label with a length of less than 38 mmCase Condition Label pitch Strip Position Fine Adjustment Example Back Feed Length Fine Adjustment Example Press the Pause key four times Axis Fine AdjustmentPress the Pause key On Section Print tone fine adjustment D J U S T Axis Fine Adjustment Example Thermal direct printing fine adjustment Print Tone Fine AdjustmentThermal transfer printing fine adjustment N T code Character Code SelectionPress the Pause key seven times At the same time On Section Font zero selection Feed key or Restart Font Zero SelectionR O F O N T Control Code Selection Code Press the Pause key CodeM a N U a LN T R O L Restart ∙ Transmissive ribbon Ribbon Type SelectionPress the Pause key ten times Select either ribbon type with Ribbon Motor Drive Voltage Fine Adjustment Press the Pause key eleven times Strip Wait Status Setting A T U S P E A C K E R S Y S T E M O F F Stacker SelectionPress the Pause key fourteen times Threshold Manual Fine Adjustment for the Black Mark Sensor R E S H O L D R R E S H O L D T Threshold Manual Fine Adjustment for the Feed Gap SensorPress the Pause key sixteen times How To Calculate Theshold Fine Adjustment Value Case When using labels with black marks reflective sensor When using labels transmissive sensorWhen using perforated labels transmissive sensor N J I code Kanji Code SelectionPress the Pause key 17 times Select either code with R O codeB O H Euro Font Code SelectionPress the Pause key 18 times Select the Euro font code with the Feed key or RTS/CTS Transmission Control Mode SelectionDTR/DSR Restart key at P U T P R I M EO N Reset Selection when the Input Prime Signal is onPress the Pause key 20 times I N T C O N D I T I O N Test Print ModeNormal Test Print Pause key I N T S P E E D N S O R T R a N S M I S S I V E Feed key or Restart key B E L L E N G T HP E R F E E D From B of the preceding Test Print Sample ∙ Print Tone Fine Adjustment Value + Process Test Print From B of the next Press the Pause key Bar code are printed on 5 labels Press the Feed key three times Sensor Setting ModeThermistor Check Black Mark Sensor Adjustment Press the Feed key Press the Pause key twice Feed Gap Sensor Adjustment Paper End Setting for Black Mark Sensor Feed key Former value is displayed Press the Pause key five times Paper End Setting for Feed Gap SensorIndicates setting complete. Press the Pause key. See Note RAM Clear Mode RAM Clear Mode Table B0H OFFType I N T E C O U N T E R C L E a R Maintenance Counter ClearR a M C L E a R M P L E T E Parameter Clear R a M E T E R C L E a R IBM PC/AT SetupFloppy Disk SW# Down Load Procedure DD-MM-YYYY Error Code ROM