Parameter Setting Mode Table | Toshiba B-570 manual

6. DIAG. TEST OPERATION

EM18-33010A (Revision Date: Dec. 10 ‘99)

6.3 PARAMETER SETTING MODE

■Parameter Setting Mode Table

Mode Name		Function

FEED ADJUST	Using this parameter the feed length is fine adjusted.

CUT ADJUST	Using this parameter the cut position or strip position is fine adjusted.

BACK FEED ADJ.	Using this parameter the back feed length from the cut/strip position to the
	home position is fine adjusted.

X ADJUST	This setting is used to finely adjust print position in the X axis.

TONE ADJUST <T>	Using this parameter the print tone is fine adjusted. The longer the print
(Thermal transfer printing)	pulse width, the darker the print tone becomes. The shorter, the lighter
TONE ADJUST <D>	the print tone becomes.
TONE ADJUST <D>
(Thermal direct printing)

FONT CODE	The character code either PC-850 or PC-8 is selected.
ZERO FONT	The font zero either 0 or ø is selected.

CODE	The command code out of AUTO, ESC/LF/NUL, or {				} is selected.




RIBBON	Ribbon type either transmissive or non-transmissive is selected.

RIBBON ADJ <FWD>	Using this parameter the torque of the ribbon motors is fine adjusted.
(Ribbon feed motor)
RIBBON ADJ <BAK>
(Ribbon feed motor)

STATUS TYPE	Whether or not the strip wait status (05H) is sent in response to the status
	request command from the PC is selectable.

STACKER SYSTEM	Use of the Stacker is selected.
	(not supported by QQ/QP models.)

THRESHOLD R	The threshold of the black mark sensor is manually fine adjusted.

THRESHOLD T	The threshold of the feed gap sensor is manually fine adjusted.

KANJI CODE	Kanji code either Windows code or original code is selected.
	(not supported by QQ/QP models.)

EURO CODE	EURO code is selected from 20H to FFH.

DTR/RTS	Transmission Control mode is selected from DTR and RTS.

INPUT PRIME	Reset ON/OFF when the		signal on is selcted.
INPUT PRIME	Reset ON/OFF when the	INPUT • PRIME	signal on is selcted.

6-14

Image 45

Toshiba B-570 manual Parameter Setting Mode Table

Contents

Series Table of Contents Checks Procedure Disconnect power cord before replacing important parts Major Unit Replacement Replacing the PS UNIT, I/F PC Board and CPU PC Board Cover and top cover An oscilloscope Turn the power off and mount the left side Replacing the Stepping Motor Replacing the TAKE-UP Motor Replacing the Ribbon Motors Replacing the Solenoid Head Up Link Solenoid Spring Pin Old type print head Replacing the Print Head Adjusting the print head position New type print head Replacing the Platen and Feed Roller Replacing the Platen and Feed Roller Replacing the Ribbon Back Tension Block Replacing the Paper Sensor Replacing the Pinch Roller Shaft ASS’Y Adjustment Correcting Skew Printing High Speed PC Interface Board B-4800-PC-QM Installation Procedure for the Optional Equipment Installation Procedure for the Optional Equipment Cutter Module B-4205-QM EM18-33010A SVO7A1003 Nov ’97 Adjusting the Cutter Guide Plates Mount the cutter cover with the two screwsRemoved Parts ’ty/Unit Front plate Expansion memory and drawing size Memory Module Fanfold Paper Guide Module B-4905-FF-QM Mechanism Description Cutter Drive Cutter Mode Harness Wiring Dirty print head Clean the print head Toshiba TECFasten the head lever completely Refer to page 2-3 to adjust Test Print Mode Parameter Setting ModeSensor Setting Mode RAM Clear Mode Outline of the DIAG. Test Operation DIAG. Test Operation L I N E Press the Pause key. See NoteU S E Maintenance Counter Printing Self Test ModeB B O N I N T E N a N C E C O U N T E R Sample Print Print Condition ∙ Preset count ∙ Print speed Trans Parameters Automatic Diagnostic Printing B B O N T R a N S M I S S I V EPress the Pause key On .2.3 Head Broken Element Check Sample Print Print Condition ∙ Preset count ∙ Print speedPROGRAM/MASK ROM Check Kanji ROM Check Eeprom Check Dram CheckFlash Memory Card Check Sensor 1 Check Label is removed Ribbon end sensor Print status content description of each sensor/switchNon-transmissive With ribbon Ribbon end Connector FCN-781P024-G/P DIP SW CheckEXP. I/O Check Head Broken Element Check R M a L E N D A D ErrorPress the Pause key twice Press the Feed key twice E R M a L H E a D C H E C K Press the Pause key Parameter Setting Mode Parameter Setting Mode Table Feed Length Fine Adjustment Press the Feed keyE D a D J U S T 2 Cut/Strip Position Fine Adjustment Press the Pause key twiceT a D J U S T At the same time On Section Axis fine adjustment Back Feed Length Fine AdjustmentPress the Pause key three times Press the Feed key Press the Pause key Cut Position Fine Adjustment Example Feed Length Fine Adjustment Example Case Condition When using a label with a length of less than 38 mmAre received Label pitch Strip Position Fine Adjustment Example Back Feed Length Fine Adjustment Example Press the Pause key On Section Print tone fine adjustment Axis Fine AdjustmentPress the Pause key four times D J U S T Axis Fine Adjustment Example Print Tone Fine Adjustment Thermal transfer printing fine adjustmentThermal direct printing fine adjustment Press the Pause key seven times Character Code SelectionN T code At the same time On Section Font zero selection Font Zero Selection R O F O N TFeed key or Restart Code Control Code Selection N T R O L CodeM a N U a LPress the Pause key Restart Press the Pause key ten times Ribbon Type Selection∙ Transmissive ribbon Select either ribbon type with Press the Pause key eleven times Ribbon Motor Drive Voltage Fine Adjustment A T U S P E Strip Wait Status Setting Stacker Selection Press the Pause key fourteen timesA C K E R S Y S T E M O F F R E S H O L D R Threshold Manual Fine Adjustment for the Black Mark Sensor Threshold Manual Fine Adjustment for the Feed Gap Sensor Press the Pause key sixteen timesR E S H O L D T Case How To Calculate Theshold Fine Adjustment Value When using labels transmissive sensor When using perforated labels transmissive sensorWhen using labels with black marks reflective sensor Press the Pause key 17 times Kanji Code SelectionN J I code Select either code with Press the Pause key 18 times Euro Font Code SelectionR O codeB O H Select the Euro font code with the Feed key or DTR/DSR Transmission Control Mode SelectionRTS/CTS Restart key at Reset Selection when the Input Prime Signal is on Press the Pause key 20 timesP U T P R I M EO N Normal Test Print Test Print ModeI N T C O N D I T I O N Pause key N S O R T R a N S M I S S I V E I N T S P E E D B E L L E N G T H P E R F E E DFeed key or Restart key From B of the preceding Test Print Sample Process Test Print ∙ Print Tone Fine Adjustment Value + Press the Pause key Bar code are printed on 5 labels From B of the next Sensor Setting Mode Thermistor CheckPress the Feed key three times Press the Feed key Press the Pause key twice Black Mark Sensor Adjustment Feed Gap Sensor Adjustment Feed key Former value is displayed Paper End Setting for Black Mark Sensor Paper End Setting for Feed Gap Sensor Indicates setting complete. Press the Pause key. See NotePress the Pause key five times RAM Clear Mode Table RAM Clear Mode OFF TypeB0H R a M C L E a R Maintenance Counter ClearI N T E C O U N T E R C L E a R M P L E T E R a M E T E R C L E a R Parameter Clear Floppy Disk SetupIBM PC/AT SW# DD-MM-YYYY Down Load Procedure ROM Error Code