Reset Selection when the Input Prime Signal is on | Toshiba B-570

6. DIAG. TEST OPERATION

EM18-33010A (Revision Date: Dec. 10 ‘99)

6.3 PARAMETER SETTING MODE

6.3.18 Reset Selection when the INPUT • PRIME Signal is ON.

Reset ON/OFF when the INPUT • PRIME signal ON is selected.

Power off

Turn on the power while holding down the [FEED] key and [PAUSE] key.

<1 > D I A G N O S T I C . V 1 . O A

Press the [FEED] key.

< 2 > P A R A M E T E R S E T

Press the [PAUSE] key 20 times.

I N P U T P R I M EO N

Select the "Reset ON/OFF when the INPUT • PRIME

signal is ON" with the [FEED] key or [RESTART] key.

•ON: The printer will restore to the initial status.

•OFF: The printer will not restore to the initial status.

Press the [PAUSE] key.

NOTES: 1. Holding the [FEED] key or [RESTART] key down for more than 0.5 seconds enable.

2.A changed “Reset ON/OFF when the INPUT • PRIME signal is ON” is stored in memory by pressing the [PAUSE] key.

6-40

Image 71

Toshiba B-570 manual Reset Selection when the Input Prime Signal is on, Press the Pause key 20 times, P U T P R I M Eo N

Contents

Series Table of Contents Checks Procedure Disconnect power cord before replacing important parts Major Unit Replacement Replacing the PS UNIT, I/F PC Board and CPU PC Board Cover and top cover An oscilloscope Turn the power off and mount the left side Replacing the Stepping Motor Replacing the TAKE-UP Motor Replacing the Ribbon Motors Replacing the Solenoid Head Up Link Solenoid Spring Pin Old type print head Replacing the Print Head Adjusting the print head position New type print head Replacing the Platen and Feed Roller Replacing the Platen and Feed Roller Replacing the Ribbon Back Tension Block Replacing the Paper Sensor Replacing the Pinch Roller Shaft ASS’Y Adjustment Correcting Skew Printing High Speed PC Interface Board B-4800-PC-QM Installation Procedure for the Optional Equipment Installation Procedure for the Optional Equipment Cutter Module B-4205-QM EM18-33010A SVO7A1003 Nov ’97 Removed Parts ’ty/Unit Front plate Adjusting the Cutter Guide PlatesMount the cutter cover with the two screws Expansion memory and drawing size Memory Module Fanfold Paper Guide Module B-4905-FF-QM Mechanism Description Cutter Drive Cutter Mode Harness Wiring Fasten the head lever completely Dirty print head Clean the print headToshiba TEC Refer to page 2-3 to adjust RAM Clear Mode Parameter Setting ModeTest Print Mode Sensor Setting Mode Outline of the DIAG. Test Operation DIAG. Test Operation U S E L I N EPress the Pause key. See Note I N T E N a N C E C O U N T E R Self Test ModeMaintenance Counter Printing B B O N Sample Print Print Condition ∙ Preset count ∙ Print speed Trans Parameters Press the Pause key On .2.3 Head Broken Element Check Automatic Diagnostic PrintingB B O N T R a N S M I S S I V E Kanji ROM Check Print Condition ∙ Preset count ∙ Print speedSample Print PROGRAM/MASK ROM Check Flash Memory Card Check Eeprom CheckDram Check Sensor 1 Check With ribbon Ribbon end Print status content description of each sensor/switchLabel is removed Ribbon end sensor Non-transmissive EXP. I/O Check Connector FCN-781P024-G/PDIP SW Check E R M a L H E a D C H E C K R M a L E N D A D ErrorHead Broken Element Check Press the Pause key twice Press the Feed key twice Press the Pause key Parameter Setting Mode Parameter Setting Mode Table E D a D J U S T Feed Length Fine AdjustmentPress the Feed key T a D J U S T 2 Cut/Strip Position Fine AdjustmentPress the Pause key twice Press the Feed key Press the Pause key Back Feed Length Fine AdjustmentAt the same time On Section Axis fine adjustment Press the Pause key three times Cut Position Fine Adjustment Example Feed Length Fine Adjustment Example Label pitch When using a label with a length of less than 38 mmCase Condition Are received Strip Position Fine Adjustment Example Back Feed Length Fine Adjustment Example D J U S T Axis Fine AdjustmentPress the Pause key On Section Print tone fine adjustment Press the Pause key four times Axis Fine Adjustment Example Thermal direct printing fine adjustment Print Tone Fine AdjustmentThermal transfer printing fine adjustment At the same time On Section Font zero selection Character Code SelectionPress the Pause key seven times N T code Feed key or Restart Font Zero SelectionR O F O N T Code Control Code Selection Restart CodeM a N U a LN T R O L Press the Pause key Select either ribbon type with Ribbon Type SelectionPress the Pause key ten times ∙ Transmissive ribbon Press the Pause key eleven times Ribbon Motor Drive Voltage Fine Adjustment A T U S P E Strip Wait Status Setting A C K E R S Y S T E M O F F Stacker SelectionPress the Pause key fourteen times R E S H O L D R Threshold Manual Fine Adjustment for the Black Mark Sensor R E S H O L D T Threshold Manual Fine Adjustment for the Feed Gap SensorPress the Pause key sixteen times Case How To Calculate Theshold Fine Adjustment Value When using labels with black marks reflective sensor When using labels transmissive sensorWhen using perforated labels transmissive sensor Select either code with Kanji Code SelectionPress the Pause key 17 times N J I code Select the Euro font code with the Feed key or Euro Font Code SelectionPress the Pause key 18 times R O codeB O H Restart key at Transmission Control Mode SelectionDTR/DSR RTS/CTS P U T P R I M EO N Reset Selection when the Input Prime Signal is onPress the Pause key 20 times Pause key Test Print ModeNormal Test Print I N T C O N D I T I O N N S O R T R a N S M I S S I V E I N T S P E E D Feed key or Restart key B E L L E N G T HP E R F E E D From B of the preceding Test Print Sample Process Test Print ∙ Print Tone Fine Adjustment Value + Press the Pause key Bar code are printed on 5 labels From B of the next Press the Feed key three times Sensor Setting ModeThermistor Check Press the Feed key Press the Pause key twice Black Mark Sensor Adjustment Feed Gap Sensor Adjustment Feed key Former value is displayed Paper End Setting for Black Mark Sensor Press the Pause key five times Paper End Setting for Feed Gap SensorIndicates setting complete. Press the Pause key. See Note RAM Clear Mode Table RAM Clear Mode B0H OFFType M P L E T E Maintenance Counter ClearR a M C L E a R I N T E C O U N T E R C L E a R R a M E T E R C L E a R Parameter Clear SW# SetupFloppy Disk IBM PC/AT DD-MM-YYYY Down Load Procedure ROM Error Code