Floppy Disk, Setup, Ibm Pc/At, Sw#, Bpc Pc | Toshiba B-570 specs

7. PROGRAM DOWN LOAD

EM18-33010A

7.1 FLOPPY DISK

7. PROGRAM DOWN LOAD

The main program for the printer has been written onto the flash ROM. If the main program is upgraded, due to the addition/change of the specification, down load the main program from the PC to the printer with the down-load floppy disk and RS-232C interface or high speed PC interface.

7.1 FLOPPY DISK

(1)Media .................... 3.5 inches (2DD)

(2)System disk .......... 1 disk (This floppy disk contains the main program written onto the printer and the tool program for down load.)

7.2 SETUP

The transmission control code for the printer must be set to either the automatic selection or manual selection (ESC, NUL, LF). For details, refer to Section 6.3.8 Control Code Selection.

(1) Program down load with RS-232C interface

IBM PC/AT
Compatible
machine	RS -232C cable

Printer

Connect the PC to the printer with an RS-232C cable. Set the DIP SW2 on the CPU PC board of the printer as follows:

	SW#	Status	Function	Description
	1	OFF	9600 BPS	Transmission Speed

	2	ON
	2	ON

	3	OFF	1 bit	Stop bit length

	4	ON	8 bits	Data length

	5	OFF	No	Presence/absence of parity

(2) Program down load with high speed PC interface

IBM PC/AT

Compatible machine

BPC PC

board

Special printer cable

BPE PC board

Printer

Install the BPC and BPE PC boards in the PC and printers, respectively, and connect both boards to each other with the special printer cable after referring to the Maintenance Manual Section 3.1. Refer to the Owner’s Manual enclosed with the high speed PC interface board kit to set the DIP SW on the BPC PC board and to install the BPC driver in the PC (hard disk drive).

7-1

Image 88

Toshiba B-570 manual Floppy Disk, Setup, Ibm Pc/At, Sw#, Bpc Pc

Contents

Series Table of Contents Procedure Checks Major Unit Replacement Disconnect power cord before replacing important parts Replacing the PS UNIT, I/F PC Board and CPU PC Board An oscilloscope Turn the power off and mount the left side Cover and top cover Replacing the Stepping Motor Replacing the Ribbon Motors Replacing the TAKE-UP Motor Replacing the Solenoid Head Up Link Solenoid Spring Pin Replacing the Print Head Old type print head Adjusting the print head position New type print head Replacing the Platen and Feed Roller Replacing the Platen and Feed Roller Replacing the Paper Sensor Replacing the Ribbon Back Tension Block Replacing the Pinch Roller Shaft ASS’Y Adjustment Correcting Skew Printing Installation Procedure for the Optional Equipment High Speed PC Interface Board B-4800-PC-QM Installation Procedure for the Optional Equipment Cutter Module B-4205-QM EM18-33010A SVO7A1003 Nov ’97 Mount the cutter cover with the two screws Adjusting the Cutter Guide PlatesRemoved Parts ’ty/Unit Front plate Memory Module Expansion memory and drawing size Fanfold Paper Guide Module B-4905-FF-QM Cutter Drive Cutter Mode Mechanism Description Harness Wiring Toshiba TEC Dirty print head Clean the print headFasten the head lever completely Refer to page 2-3 to adjust Parameter Setting Mode Test Print ModeSensor Setting Mode RAM Clear Mode DIAG. Test Operation Outline of the DIAG. Test Operation Press the Pause key. See Note L I N EU S E Self Test Mode Maintenance Counter PrintingB B O N I N T E N a N C E C O U N T E R Sample Print Print Condition ∙ Preset count ∙ Print speed Parameters Trans B B O N T R a N S M I S S I V E Automatic Diagnostic PrintingPress the Pause key On .2.3 Head Broken Element Check Print Condition ∙ Preset count ∙ Print speed Sample PrintPROGRAM/MASK ROM Check Kanji ROM Check Dram Check Eeprom CheckFlash Memory Card Check Sensor 1 Check Print status content description of each sensor/switch Label is removed Ribbon end sensorNon-transmissive With ribbon Ribbon end DIP SW Check Connector FCN-781P024-G/PEXP. I/O Check R M a L E N D A D Error Head Broken Element CheckPress the Pause key twice Press the Feed key twice E R M a L H E a D C H E C K Parameter Setting Mode Press the Pause key Parameter Setting Mode Table Press the Feed key Feed Length Fine AdjustmentE D a D J U S T Press the Pause key twice 2 Cut/Strip Position Fine AdjustmentT a D J U S T Back Feed Length Fine Adjustment At the same time On Section Axis fine adjustmentPress the Pause key three times Press the Feed key Press the Pause key Feed Length Fine Adjustment Example Cut Position Fine Adjustment Example When using a label with a length of less than 38 mm Case ConditionAre received Label pitch Strip Position Fine Adjustment Example Back Feed Length Fine Adjustment Example Axis Fine Adjustment Press the Pause key On Section Print tone fine adjustmentPress the Pause key four times D J U S T Axis Fine Adjustment Example Thermal transfer printing fine adjustment Print Tone Fine AdjustmentThermal direct printing fine adjustment Character Code Selection Press the Pause key seven timesN T code At the same time On Section Font zero selection R O F O N T Font Zero SelectionFeed key or Restart Control Code Selection Code CodeM a N U a L N T R O LPress the Pause key Restart Ribbon Type Selection Press the Pause key ten times∙ Transmissive ribbon Select either ribbon type with Ribbon Motor Drive Voltage Fine Adjustment Press the Pause key eleven times Strip Wait Status Setting A T U S P E Press the Pause key fourteen times Stacker SelectionA C K E R S Y S T E M O F F Threshold Manual Fine Adjustment for the Black Mark Sensor R E S H O L D R Press the Pause key sixteen times Threshold Manual Fine Adjustment for the Feed Gap SensorR E S H O L D T How To Calculate Theshold Fine Adjustment Value Case When using perforated labels transmissive sensor When using labels transmissive sensorWhen using labels with black marks reflective sensor Kanji Code Selection Press the Pause key 17 timesN J I code Select either code with Euro Font Code Selection Press the Pause key 18 timesR O codeB O H Select the Euro font code with the Feed key or Transmission Control Mode Selection DTR/DSRRTS/CTS Restart key at Press the Pause key 20 times Reset Selection when the Input Prime Signal is onP U T P R I M EO N Test Print Mode Normal Test PrintI N T C O N D I T I O N Pause key I N T S P E E D N S O R T R a N S M I S S I V E P E R F E E D B E L L E N G T HFeed key or Restart key From B of the preceding Test Print Sample ∙ Print Tone Fine Adjustment Value + Process Test Print From B of the next Press the Pause key Bar code are printed on 5 labels Thermistor Check Sensor Setting ModePress the Feed key three times Black Mark Sensor Adjustment Press the Feed key Press the Pause key twice Feed Gap Sensor Adjustment Paper End Setting for Black Mark Sensor Feed key Former value is displayed Indicates setting complete. Press the Pause key. See Note Paper End Setting for Feed Gap SensorPress the Pause key five times RAM Clear Mode RAM Clear Mode Table Type OFFB0H Maintenance Counter Clear R a M C L E a RI N T E C O U N T E R C L E a R M P L E T E Parameter Clear R a M E T E R C L E a R Setup Floppy DiskIBM PC/AT SW# Down Load Procedure DD-MM-YYYY Error Code ROM