Toshiba B-570 manual Sample Print Print Condition ∙ Preset count ∙ Print speed

6. DIAG. TEST OPERATION

EM18-33010A (Revision Date: Dec. 10 ‘99)

6.2 SELF TEST MODE

■Sample Print [Print Condition]

∙ Preset count	: 1
∙ Print speed	: 127 mm/sec.
∙ Sensor	: No sensor

∙Printing method : Thermal transfer

∙ Supply length	: 50 mm
∙ Issuing mode	: Batch printing
	(without rewinder)

1) Maintenance Counter

(1)	TL FEED		1882.3km	[PC]
(2)	FEED		20.5km	FEED	-10.0mm
(3)	PRINT		15.0km	CUT	-5.0mm
(4)	CUT		148150	BACK	+3.0mm
(5)	HEAD U/D		170	TONE(T)	+3step
(6)	RIBBON		32h	TONE(D)	+5step
(7)	SOLENOID		0h	[KEY]
(8)	232C ERR		1	FEED	+5.0mm
(9)	SYSERR		0	CUT	-1.5mm
(10)	PW FAIL		0	BACK	+0.5mm
(11)	FONT	[PC-850] [0]		TONE(T)	+0step
(12)	CODE	[ESC LF NUL]		TONE(D)	+1step
(13)	RIBN	[TRANS.]		X ADJ.	+35.0mm

(25)RIBN ADJ. [PC] + 0 +0 [KEY] + 0 +0

(26)STATUS [OFF]

(27)THRESHOLD R 1.0V

(28)THRESHOLD T 1.4V

(29)KANJI [TYPE1]

(30)EURO CODE B0H

(31)STACKER [OFF]

(32)DTR/RTS [DTR]

(33)INPUT PRIME [ON]

(14)

(15)

(16)

(17)

(18)

(19)

(20)

(21)

(22)

(23)

(24)

Fig. 6-1

#	Item	Count Condition	Range
(1)	Total media distance	Counted when the feed motor drives to feed, print and	0.0 ~ 3200.0 km
		issue the media. (Counted also during ribbon save
	covered
(2)	Media distance	operation and back feed.) [See NOTE 2].	0.0 ~ 200.0 km
	Print distance	Counted while printing. (Feeding and issuing media,
(3)		and ribbon saving operation are not counted.)	0.0 ~ 200.0 km
		[See NOTE 2.]
(4)	Cut count	Counts every cut. [See NOTE 3.]	0 ~ 1000000 times
	Head up and down	Counts every up and down of the print head using the
(5)	count	solenoid for ribbon save operation.	0 ~ 2000000 times
		(Up + Down = 1 count) [See NOTE 3.]
	Ribbon motor driving	Counts when the ribbon motor drives to feed, print
(6)	time	and issue the media. (The driving time is not counted	0 ~ 2000 hours
		during ribbon saving operation, but is during back
		feed.) [See NOTE 4.]
(7)	Solenoid driving time	Counted during ribbon saving operation.	0 ~ 1000 hours
		[See NOTE 4.]
(8)	RS-232C hardware	Counted when a parity, overrun or framing error	0 ~ 255 times
	error count	occurs. [See NOTE 5.]
(9)	System error count	Counted when a zero-dividing error occurs or	0 ~ 15 times
		undefined command is retrieved.
(10)	Momentary power	Counted when a momentary power failure occurs.	0 ~ 15 times
	failure count
NOTES: 1. Item from (2) through (10) are initialized to “0” after RAM clear.

2.If the distance is 5.5 m or less, it is rounded down and no data is added to the memory at power off.

3.If the count is 31 counts or less, it is rounded down and no data is added to the memory at power off.

4.If the driving time is 27 sec. or less, it is rounded down and no data is added to the memory at power off.

5.When a sent command results in an error, the same number as the data capacity of the command is counted by byte.

6-4