Parameters, Trans | Toshiba B-570 instruction

6. DIAG. TEST OPERATION

EM18-33010A (Revision Date: Dec. 10 ‘99)

6.2 SELF TEST MODE

2) Parameters

#			Item					Contents
(11)			Character code selection		PC-850			: PC-850
					PC-8			: PC-8
			Font zero selection		0			: No slash used.
					Ø			: Slash used.

(12)			Control code selection		AUTO			: Automatic selection
					ESC LF NUL			: ESC LF NUL mode
					{		}	: Mainframe mode



					1B 1C 1D			: Manual mode

(13)			Ribbon type selection		TRANS.			: Transmissive ribbon
					NON TRANS. : Non-transmissive ribbon

(14)			Feed length fine adjustment		-50.0 mm to +50.0 mm
(19)			(PC), (KEY)

(15)			Cut/strip position fine adjustment		-50.0 mm to			+50.0 mm
(20)			(PC), (KEY)
(16)			Back feed length fine adjustment		-9.9 mm to +9.9 mm
(21)			(PC), (KEY)

(17)			Print tone fine adjustment		-10 step to +10 step
(22)			(Thermal transfer) (PC), (KEY)

(18)			Print tone fine adjustment		-10 step to +10 step
(23)			(Thermal direct) (PC), (KEY)

(24)			X axis fine adjustment		-99.5 mm to +99.5 mm
(25)			Ribbon Motor		+15 step to +0 step

(26)			Strip wait status		1: Strip wait status is not sent to the PC.
					2: Strip wait status is sent to the PC.

(27)			Threshold manual fine		0.0 V to 4.0 V
			adjustment for the black mark
			sensor

(28)			Threshold manual fine		0.0V to 4.0 V
			adjustment for the feed gap
			sensor

(29)			Kanji code type		TYPE 1: Windows code
			(not supported by QQ/QP		TYPE 2: Original code
			models.)

(30)			Euro font code setting		20H to FFH

(31)			Stacker		OFF: No stacker
			(not supported by QQ/QP		ON: with stacker
			models.)

(32)			Transmission Control Mode		DTR: READY/BUSY (DTR) protocol (DTR/DSR)
					DTR: READY/BUSY (DTR) protocol (DTR/DSR)
					RTS: READY/BUSY (RTS) protocol (RTS/CTS)
	(33)		Reset selection when the		ON: The printer will restore to the initial status.
					ON: The printer will restore to the initial status.
			INPUT • PRIME	signal is ON.	OFF: The printer will not restore to the initial status.
					OFF: The printer will not restore to the initial status.

6-5

Image 36

Toshiba B-570 manual Parameters, Trans

Contents

Series Table of Contents Procedure Checks Major Unit Replacement Disconnect power cord before replacing important parts Replacing the PS UNIT, I/F PC Board and CPU PC Board An oscilloscope Turn the power off and mount the left side Cover and top cover Replacing the Stepping Motor Replacing the Ribbon Motors Replacing the TAKE-UP Motor Replacing the Solenoid Head Up Link Solenoid Spring Pin Replacing the Print Head Old type print head Adjusting the print head position New type print head Replacing the Platen and Feed Roller Replacing the Platen and Feed Roller Replacing the Paper Sensor Replacing the Ribbon Back Tension Block Replacing the Pinch Roller Shaft ASS’Y Adjustment Correcting Skew Printing Installation Procedure for the Optional Equipment High Speed PC Interface Board B-4800-PC-QM Installation Procedure for the Optional Equipment Cutter Module B-4205-QM EM18-33010A SVO7A1003 Nov ’97 Adjusting the Cutter Guide Plates Mount the cutter cover with the two screwsRemoved Parts ’ty/Unit Front plate Memory Module Expansion memory and drawing size Fanfold Paper Guide Module B-4905-FF-QM Cutter Drive Cutter Mode Mechanism Description Harness Wiring Dirty print head Clean the print head Toshiba TECFasten the head lever completely Refer to page 2-3 to adjust Parameter Setting Mode Test Print ModeSensor Setting Mode RAM Clear Mode DIAG. Test Operation Outline of the DIAG. Test Operation L I N E Press the Pause key. See NoteU S E Self Test Mode Maintenance Counter PrintingB B O N I N T E N a N C E C O U N T E R Sample Print Print Condition ∙ Preset count ∙ Print speed Parameters Trans Automatic Diagnostic Printing B B O N T R a N S M I S S I V EPress the Pause key On .2.3 Head Broken Element Check Print Condition ∙ Preset count ∙ Print speed Sample PrintPROGRAM/MASK ROM Check Kanji ROM Check Eeprom Check Dram CheckFlash Memory Card Check Sensor 1 Check Print status content description of each sensor/switch Label is removed Ribbon end sensorNon-transmissive With ribbon Ribbon end Connector FCN-781P024-G/P DIP SW CheckEXP. I/O Check R M a L E N D A D Error Head Broken Element CheckPress the Pause key twice Press the Feed key twice E R M a L H E a D C H E C K Parameter Setting Mode Press the Pause key Parameter Setting Mode Table Feed Length Fine Adjustment Press the Feed keyE D a D J U S T 2 Cut/Strip Position Fine Adjustment Press the Pause key twiceT a D J U S T Back Feed Length Fine Adjustment At the same time On Section Axis fine adjustmentPress the Pause key three times Press the Feed key Press the Pause key Feed Length Fine Adjustment Example Cut Position Fine Adjustment Example When using a label with a length of less than 38 mm Case ConditionAre received Label pitch Strip Position Fine Adjustment Example Back Feed Length Fine Adjustment Example Axis Fine Adjustment Press the Pause key On Section Print tone fine adjustmentPress the Pause key four times D J U S T Axis Fine Adjustment Example Print Tone Fine Adjustment Thermal transfer printing fine adjustmentThermal direct printing fine adjustment Character Code Selection Press the Pause key seven timesN T code At the same time On Section Font zero selection Font Zero Selection R O F O N TFeed key or Restart Control Code Selection Code CodeM a N U a L N T R O LPress the Pause key Restart Ribbon Type Selection Press the Pause key ten times∙ Transmissive ribbon Select either ribbon type with Ribbon Motor Drive Voltage Fine Adjustment Press the Pause key eleven times Strip Wait Status Setting A T U S P E Stacker Selection Press the Pause key fourteen timesA C K E R S Y S T E M O F F Threshold Manual Fine Adjustment for the Black Mark Sensor R E S H O L D R Threshold Manual Fine Adjustment for the Feed Gap Sensor Press the Pause key sixteen timesR E S H O L D T How To Calculate Theshold Fine Adjustment Value Case When using labels transmissive sensor When using perforated labels transmissive sensorWhen using labels with black marks reflective sensor Kanji Code Selection Press the Pause key 17 timesN J I code Select either code with Euro Font Code Selection Press the Pause key 18 timesR O codeB O H Select the Euro font code with the Feed key or Transmission Control Mode Selection DTR/DSRRTS/CTS Restart key at Reset Selection when the Input Prime Signal is on Press the Pause key 20 timesP U T P R I M EO N Test Print Mode Normal Test PrintI N T C O N D I T I O N Pause key I N T S P E E D N S O R T R a N S M I S S I V E B E L L E N G T H P E R F E E DFeed key or Restart key From B of the preceding Test Print Sample ∙ Print Tone Fine Adjustment Value + Process Test Print From B of the next Press the Pause key Bar code are printed on 5 labels Sensor Setting Mode Thermistor CheckPress the Feed key three times Black Mark Sensor Adjustment Press the Feed key Press the Pause key twice Feed Gap Sensor Adjustment Paper End Setting for Black Mark Sensor Feed key Former value is displayed Paper End Setting for Feed Gap Sensor Indicates setting complete. Press the Pause key. See NotePress the Pause key five times RAM Clear Mode RAM Clear Mode Table OFF TypeB0H Maintenance Counter Clear R a M C L E a RI N T E C O U N T E R C L E a R M P L E T E Parameter Clear R a M E T E R C L E a R Setup Floppy DiskIBM PC/AT SW# Down Load Procedure DD-MM-YYYY Error Code ROM