Viewing Fan Status | Alcatel-Lucent 6600 manual

OmniSwitch 6600 Family Chassis and Hardware Components	Temperature Management

Viewing Fan Status

The switch also constantly monitors fan operation. If any of the three fans unexpectedly shuts down, the switch sends out a trap to the user and the FAN LED on the chassis front panel displays amber.

Note. For detailed LED information, including the FAN LED, refer to “Status LEDs” on page 2-18.

To check the current fan status, use the show fan command. For example:

-> show fan Chassis Fan Status

-------+---+-----------

11 Running

12 Running

13 Running

In the example above, all three fans are operating normally.

Viewing Fan Status for Stacked Configurations

When entering the show fan command on the primary switch in a stacked configuration, you can either enter only the show fan syntax or you can specify a specific slot number. For more information, refer to the examples below:

A Slot Number is Specified

If you specify a slot number after the command syntax, fan status information for only the corresponding switch displays. For example:

-> show fan

Chassis Fan Status

-------+---+-----------

11 Running

12 Running

13 Running

In the example above, fan status displays only for the switch operating in slot 3.

OmniSwitch 6600 Family Hardware Users Guide September 2006

page 2-56

Image 80

Alcatel-Lucent 6600 manual Viewing Fan Status for Stacked Configurations

Contents

OmniSwitch 6600 Family Hardware Users Guide OmniSwitch 6600 Family Hardware Users Guide September Contents Temperature Errors Viewing Fan Status Priority Disconnect is Enabled Incoming PD Port has Highest CLI Commands Supported on Both the Primary and Secondary Index-1 Page About This Guide Supported Platforms Unsupported Platforms When Should I Read this Manual? What is in this Manual?What is Not in this Manual? Who Should Read this Manual? Stage 1 Using the Switch for the First Time Stage 2 Gaining Familiarity with Basic Switch FunctionsHow is the Information Organized? Documentation Roadmap Stage 3 Integrating the Switch Into a Network Anytime OmniSwitch 6600 Family Getting Started Guide Related Documentation Technical Support Page OmniSwitch 6600 Family Stand-Alone Stand-Alone and Stacked ConfigurationsStacked Configurations Availability Features Smart Continuous Switching Software Rollback Hot Swapping Hardware Monitoring Automatic MonitoringLEDs User-Driven Monitoring Application Examples Single Office Building with 1000 Users Medium Campus with 1500 Users OmniPCXPage OmniSwitch 6600 Family Chassis and Hardware Components OmniSwitch OmniSwitch 6624 Front Panel OS6624 Specifications 10/100 Ethernet Port Specifications OmniSwitch 6600-U24 OmniSwitch 6600-U24 Front Panel Console Port Gigabit Ethernet Uplink Module Slot OS6600-U24 Specifications Mbps Ethernet SFP Port Specifications SFP OmniSwitch 6600-P24 OmniSwitch 6600-P24 Front Panel OmniSwitch 6600-P24 OS6600-P24 Specifications 10/100 Power over Ethernet PoE Port Specifications OmniSwitch 6648 Front Panel TM OmniSwitch OS6648 Specifications OmniSwitch 6602-24 Front Panel OS6602-24 Specifications OmniSwitch 6602-48 Front Panel 10/100 Ethernet Ports Console Port OS6602-48 Specifications Status LEDs Front Panel LED Descriptions OS6648 Shown OmniSwitch 6600 Family Chassis and Hardware Components OmniSwitch 6600 Family Rear Panel Redundant Power Supply BayPower Connector Socket PoE Power Connector Airflow Considerations Mounting the SwitchOmniSwitch 6600 Family Chassis Top View Installation Options Installing the Switch on a Tabletop or Bench Attaching the Switch to the Rack Attaching a Rack-Mount Flange Rack Mounting Stacked Configurations Power Cords SpecificationsPower Cord Types Grounding the Chassis Power Switch. indicates on position indicates off position Backup Power SupplyBackup Power Supply Front Panel OS6600-BPS Shown OS6600-BPS-P Backup Power Supply Front Panel OS6600-BPS-P Backup Power Supply Back PanelOS6600-P24 Connectors BPS Power Connector Power Supply Specifications OS6600-BPS Backup Power Supply Specifications Power Supply Redundancy OS6602-BPS Backup Power Supply SpecificationsOS6602-BPS-DC Backup Power Supply Specifications OS6600-BPS-P PoE Backup Power Supply Specifications OmniSwitch 6600 Family Redundant AC Circuit Example Backup Factory-Installed Primary Power SupplyAC Circuit BackUp Factory-Installed Primary Power Supply Redundant AC Circuit Recommendation Hot Swapping Installing a Backup Power SupplyOrienting the Backup Power Supply Inserting the Backup Power Supply Tightening the Captive Screws Loosening the Captive Screws Removing a Backup Power SupplyRemoving the Backup Power Supply Viewing Primary and Backup Power Supply Status Blank Cover Panel Requirement No Slot Number is Specified Viewing Power Supply Status for Stacked ConfigurationsSlot Number is Specified Gigabit Ethernet Uplink Modules OS6600-GNI-U2OS6600-GNI-U2 Gigabit Ethernet Uplink Front Panel MiniGBIC Slots OS6600-GNI-U2 Uplink Module Specifications OS6600-GNI-C2 Ethernet Uplink Front Panel OS6600-GNI-C2 Uplink Module SpecificationsOS6600-GNI-C2 Stacking Module Specifications Hssdc Stacking ConnectorsStacking Module Stacking Module Front Panel Installing Uplink and Stacking Modules Inserting the Uplink or Stacking Module LINK/ACT LINK/ACT Removing Uplink and Stacking Modules Removing the Module Mini Gigabit Interface Converters MiniGBICs Mini Gigabit Interface Converter MiniGBIC MiniGBIC Specifications MiniGBIC-SX Technical SpecificationsMiniGBIC-LX Technical Specifications MiniGBIC-LH-70 Technical Specifications Installing MiniGBICs Inserting the MiniGBIC OS6648 Shown Installed MiniGBIC OS6648 Shown Removing MiniGBICs Mbps SFPs OS6600-U24 SFP Module Mbps SFP Specifications SFP-100-LC-MM Technical SpecificationsSFP-100-LC-SM15 Technical Specifications SFP-100-LC-SM40 Technical Specifications SFP-100-MTRJ-MM Technical Specifications Mtrj Installing SFPs OS6600-U24 Inserting the SFP Removing SFPs OS6600-U24 Temperature Management Viewing Chassis Temperature Status Viewing Temperature Status for Stacked Configurations Temperature Errors Viewing Fan Status for Stacked Configurations Viewing Fan Status No Slot Number is Specified Chassis Airflow Right Side Air Intake VentLeft Side Fan Exhaust Vents Air Exhaust. The airflow Blank Cover Panels Effects of Missing Blank Panels on Chassis Airflow Pinouts 10/100 Ethernet Port RJ-45 PinoutCopper Gigabit Ethernet Port RJ-45 Pinout Pin Number Description Pin Number Signals as DCE Console Port RS232 Console Port Female DB9 Connector PinoutRJ-45 Console Port Connector Pinout Console Port Serial Connection Default SettingsModifying the Serial Connection Settings Additional table output not shown Configuring X-ON/X-OFF Protocol Session xon-xoff disable Viewing Basic Chassis Information Hardware Information Slot and Component Information Detailed Slot and Component Information Screen output on next Gbic Basic Primary Slot and Component Information Basic Chassis Information ON/X-OFF Protocol Status MAC Range Guidelines Managing MAC Addresses on the SwitchOmniSwitch 6600 Family MAC Range Specifications Determining Current MAC Address Allocation on the Switch Base Chassis MAC Address in Stacked ConfigurationsBase Chassis MAC Address as Unique Identifier Viewing the Base Chassis MAC Address Installing and Managing Power over Ethernet PoE This Chapter Power over Ethernet Specifications Watts Viewing OS6600-BPS-P Status Configuring Power over Ethernet Parameters Power over Ethernet DefaultsUnderstanding and Modifying the Default Settings Setting the PoE Operational Status Disabling PoE Configuring the Total Power Allocated to a PortConfiguring the Total Power Allocated to a Switch Setting Port Priority Levels Setting the Capacitor Detection Method Lanpower capacitor-detection 2 disable Setting Priority Disconnect Status Understanding Priority DisconnectDisabling Priority Disconnect Enabling Priority Disconnect Understanding Priority Disconnect Monitoring Power over Ethernet via the CLI Priority Disconnect is Disabled Monitoring Power over Ethernet via the CLI Managing OmniSwitch 6600 Family Stacks Specifications and Default Values Parameter Description Configuration Steps Default Value Stack Composed of Four OmniSwitch 6648 Switches Stack Overview Stacking Resiliency and Redundancy Slot Numbers within a Stack CMM Roles in a Stack CMM Role Redundancy Switch Primary CMM CommandsChassis Management and Monitoring Commands File Management Commands Session Management Commands Switch Logging and Monitoring CommandsMemory Monitoring Commands Setting Up a Stacked Configuration Assigning Slot Numbers Continue to Connecting Cables to Stacking Ports on SEL Button Location Stack of Four Switches with Unique Slot Numbers Slot Numbering Example Connecting Cables to Stacking Ports Attaching the Stacking Cable to a Stacking Port Connecting the Switches in the Stack Recommended Redundant Connection Between Switches Redundant Stack Connection Stacking Cable Redundancy Example Verifying Primary and Secondary Status for the Stack Booting the StackVerifying Slot Number Assignments Idle Status Managing Switches in a Stack Reloading a Switch with a Primary or Secondary CMM RoleReloading the Switch with the Primary CMM Role Reloading the Switch with the Secondary CMM Role Synchronizing Switches in a Stack Changing the Secondary CMM Role to Primary Resetting All Switches in a Stack Stack Behavior During Takeover Monitoring Stack Topology Managing and Monitoring OmniSwitch 6600 Family StacksMonitoring Stacks Secondary Active Declaration of Conformity CE Mark Waste Electrical and Electronic Equipment Weee Statement Safety Standards Safety and Environmental StandardsStandards Compliance EMC Standards CISPR22 Class a warning FCC Class A, PartCanada Class a Statement Vcci Class a Warning for Taiwan and Other Chinese Markets Translated Safety Warnings Chassis Lifting WarningBlank Panels Warning Electrical Storm Warning Installation Warning Invisible Laser Radiation Warning Lithium Battery Warning Operating Voltage Warning Power Disconnection Warning Proper Earthing Requirement WarningFrançais Español Read Important Safety Information Warning Restricted Access Location Warning Wrist Strap Warning Instrucciones de seguridad en español Advertencia sobre una apropiada conexión a tierra Leer información importante de seguridadAdvertencia de acceso restringido Advertencia de pulsera antiestática Numerics Commit file command Commit system commandCopy flash-synchro command Show hardware info command Reload all command Reload command Session xon-xoff commandShow chassis command Show cmm command Show fan command Takeover command Temp-threshold command