Troubleshooting

If a problem should arise, first check the following.1.Are the connections correct?2.Have you operated the receiver according to the Operating Instructions?3.Are the speakers, and other connected components operating properly?

If this unit is not operating properly, check the items listed in the table below. Should the problem persist, there may be a malfunction. Disconnect the power immediately and contact your store of purchase.

SymptomCauseMeasures

Page

Display not lit and sound not

• Power supply cord not plugged in securely.

• Check the insertion of the power supply cord

42

produced when power switch

 

plug.

 

set to on.

 

 

 

 

 

 

 

 

• Speaker cables not securely connected.

• Connect securely.

16, 17

Display lit but sound not

• FUNCTION knob position is not appropriate.

• Switch to the proper position.

44

• Volume control set to minimum.

• Turn volume up to suitable level.

44

produced.

• Muting is on.

• Switch off Muting.

45

 

 

• No digital signal is being input.

• Properly select a digital signal input source.

104

 

 

 

 

 

AVR-5805CI’s video output terminals and

• Check that the connections are correct.

16, 17,

 

monitor’s input terminals are not properly

 

27 ~ 42

 

connected.

 

 

Nothing is displayed on monitor.

• TV’s input setting is wrong.

• Set the TV’s input selector to the terminals to

 

 

which video signals are connected.

 

 

• The PURE DIRECT mode is set.

• Set a surround mode other than the PURE

50

 

 

DIRECT mode.

 

 

 

 

 

 

• DVD player’s audio output setting is not set to

• Make the DVD player’s initial settings.

No DTS sound is produced.

bit stream.

 

 

• DVD player is not DTS-compatible.

• Use a DTS-compatible player.

 

 

AVR-5805CI’s input setting is set to analog.

• Set to AUTO or DTS.

47, 48

 

 

 

 

Ultra2 Cinema / THX Music

• Surround back speaker set to 1.

• Connect two surround back speakers.

16, 17,

Mode / THX Games Mode

 

 

140, 141,

cannot be set.

 

 

148

 

 

 

 

 

• Copying between a source such as DVD and a

• Copying is not possible.

Copying from DVD to VCR is not

VCR is not usually possible, as DVDs are often

 

 

possible.

encoded with copy-protection signals that

 

 

 

prevent VCR recording.

 

 

 

 

 

 

 

• Subwoofer’s power is not on.

• Turn on the power.

No sound is produced from

• Subwoofer’s initial setting is set to “NO”.

• Set the setting to “YES”.

140, 141

• Subwoofer’s output is not connected.

• Connect properly.

17, 42

subwoofer.

• The subwoofer’s channel volume level is set

• Turn the subwoofer’s channel volume level up.

64

 

 

to “OFF”.

 

 

 

 

 

 

No test tones are produced.

• Surround mode is set to a mode other than

• Set to STANDARD (Dolby/DTS Surround).

STANDARD (Dolby/DTS Surround).

 

 

 

 

 

 

 

 

 

No sound is produced from

• Surround mode is set to “STEREO”.

• Set to a mode other than “STEREO”.

surround speakers.

 

 

 

 

 

 

 

 

• Batteries dead.

• Replace with new batteries.

9

This unit does not operate

• Remote control unit too far from this unit.

• Move closer.

9

• Obstacle between this unit and remote control

• Remove obstacle.

9

properly when remote control

unit.

 

 

unit is used.

 

 

• Different button is being pressed.

• Press the proper button.

 

 

< and > ends of battery inserted in reverse.

• Insert batteries properly.

9

 

 

 

 

157