Easy Setup and Operation

About the error message

These error messages will be displayed when performing the measurements of Auto Setup and the automatic measurements can not be completed because of the speaker arrangement, measurement environment, or other factors. Please check the following matters, reset the pertinent items, and measure again. Be sure to turn off the AVR-5805CI’s power before checking the speaker connections.

Screen exampleCauseMeasures

 

 

 

 

 

 

 

 

q The speakers required for producing suitable

• Check that the pertinent speakers

 

 

 

 

 

 

 

 

reproduction have not been detected.

are properly connected.

 

 

 

 

 

 

 

 

• The front L speaker was detected, but the

 

 

 

 

 

 

 

 

 

front R speaker was not detected.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Only one channel of the surround (A) and

 

 

 

 

 

 

 

 

 

surround (B) speakers was detected.

 

 

 

 

 

 

 

 

 

• Sound was output from the R channel when

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

only one surround back speaker was

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

connected.

 

 

 

 

 

 

 

 

 

• The surround back or the surround (B) speaker

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

was detected, but the surround (A) speaker

 

 

 

 

 

 

 

 

 

was not detected.

 

 

 

 

 

 

 

 

 

If multiple errors occur, press the CURSOR F or

 

Gbutton to check the contents.

 

 

 

 

 

 

 

 

 

 

 

 

w The speaker polarity is connected in reverse.

• Check the polarity of the pertinent

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

speakers.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

If multiple errors occur, press the CURSOR F or

• For some speakers, the screen

 

 

 

 

 

 

 

 

 

 

 

 

G button to check the contents.

below may be displayed even though

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the speakers are properly connected.

 

 

 

 

 

 

 

 

 

 

 

 

 

If so, select “Skip0”.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

e There is too much ambient noise in the room

• Either turn off the power of the

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

and the measurements cannot be made

device that generated the noise

 

 

 

 

 

 

 

 

 

 

 

 

accurately.

during the measurements or move

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

the device away.

 

 

 

 

 

 

 

 

 

 

 

 

 

• Try again at a time when it is quieter.

 

 

 

 

 

 

 

 

 

 

 

 

r The sound level that is output from the

• Check the placement and orientation

 

 

 

 

 

 

 

 

 

 

 

 

speakers and/or subwoofer is too low.

of the loudspeakers.

 

 

 

 

 

 

 

 

 

 

 

 

 

• Adjust the subwoofer’s output level.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

t The measurement microphone is not

• Connect the measurement microphone

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

connected, or all of speakers have not been

to the SETUP MIC jack.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

detected.

• Check the speaker connection.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

y The front L speaker was not detected.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

26