Relay Card | Emerson 40-200KVA specs

Options

Figure 69 Liebert® IntelliSlot™ Web card display

Relay Card

The relay card provides voltage-free contact closures for remote monitoring of alarm conditions.

Delivering On Battery, On Bypass, Low Battery, Summary Alarm, UPS Fault and On UPS signals, the easy-to-install card integrates with AS/400 computers (additional cable required) and other relay contact monitoring systems.

The relay card is rated for 24 VAC/DC at 1A and supported in any of the three Liebert® IntelliSlot® bays on the Liebert NX™.Refer to the Liebert Intellislot Relay Card user manual, SL-23211, for pin and jumper configuration. The manual is available at Liebert’s Web site: www.liebert.com

108

Image 118

Emerson 40-200KVA user manual Relay Card, Liebert IntelliSlot Web card display

Contents

Liebert NX UPS Page Table of Contents UPS Specifications Options Operator Control and Display Panel Installation Drawings OperationOperating Instructions Specifications and Technical Data Appendix a UPS Status Messages Connecting EPO push button Tables 114 Viii Important Safety Instructions Page Battery Cabinet Precautions Page Glossary of Symbols Introduction External Inspections Internal Inspections Preliminary Checks UPS Location Special Considerations for Parallel Systems Battery LocationConsiderations in Moving the Liebert NX Final Position Clearances Floor InstallationMechanical Considerations Cable Entry Optional Cabinets Front of Units Front of Units Cable Rating Power CablingLug Size and Torque Requirements UPS Input Configuration Cabling Guidelines Protective Devices Safety GroundCable Connections UPS Rectifier and Bypass Input Supply Common Input Connections Cabling ProcedureDual Input Connections Output System Connections-Ensure Correct Phase Rotation Frequency Converter Mode Monitor Board Features Control Cables J13 J21 J25 J22 J23 J12 J15J16 J26 J30 Dry Contacts Maintenance Bypass Cabinet InterfaceMaintenance bypass cabinet interface Input Dry Contacts BCB control interface Battery Circuit Breaker Control InterfaceOutput Dry Contacts Output dry contact relays EPO input contact relays EPO Input-OptionalIndicates Pin Safety External Battery Cabinet Installation Battery Cabinets Installation Considerations Connecting the BatteriesInsulated Post Tray Handle For Cabling Connecting the Battery Cabinet to the UPS Non-Standard Batteries BCB Shunt Trip Alber Monitoring System-Optional Performance Requirements LBS Cable and SettingsLoad Bus Synchronization LBS Cable UPS Features of Parallel System Configuring Parallel Sbasystem OperationGeneral 480V, 3W Output 480V, 3W System Output480V, 3W System Input RIB 2 UPS Module RIB 3 UPS Module RIB 4 UPS Module Operation Modes Summary Installing Parallel SystemOperating Principles Redundancy Paralleling Conditions for Parallel System Preliminary Checks Cabinet InstallationPower Cables Parallel Control Cables Parallel System Control Cables Auxiliary Dry Contact Cables Normally Open EPO Normally Closed EPO UPS mechanical characteristics UPS Mechanical CharacteristicsEnvironmental characteristics Conformity and Standards UPS Electrical Characteristics UPS terminal Rated Power kVA 100 120 160 Rectifier input powerInput Rectifier Rated Power kVA 100 120 160 200 Liebert-approved replacement batteriesBattery Models Manufacturer Supplied DC Intermediate Circuit Inverter output Inverter OutputBypass Input Bypass input Normal UPS Mode Liebert BDC Cable Installation Maintenance ModeLocating the Cabinet Input/Output Wiring Control wiring for Liebert NX UPS to Liebert BDC Liebert BDC connection to UPS Install Circuit breaker schedule Main circuit breaker Interrupting 208V Main panelboard circuit breakerPanelboard branch circuit breaker 225A T3N225TW Subfeed circuit breaker Square D I-Line panelboard circuit breaker Bolting Cabinets Together Bolting a Liebert Nxups to a Liebert BDC Outline drawing, Liebert BDC, 47 cabinet Weights, Liebert NX 40-120kVA Outline drawing, Liebert NX 40-120kVA Torque Battery cabinet groundBattery cabinet circuit breaker Unit Rating Bolt Size Lb-in N-m 80-120 225 Liebert NX 160-200kVA dimensions-front and left side Electrical specifications, Liebert NX 160-200kVA U389641 GND Front View Left View TOP View Liebert NX 160-200kVA main components-typical unit Detail a 224mm 609.3 872.2 34.3 Detail B Front Detail a CBB Installation Drawings Front Top Right Side Top Front Rear Without Covers Front Door Open Run From Conductors Front Without Covers Left Side Single module block diagram dual input configuration General Description Bypass Supplies Normal ModeBattery Mode Operating Modes Parallel Redundancy Mode System Expansion Maintenance ModeEco Mode Operator Control Panel Display Panel Layout Mimic Display Indicators Mimic display status indicators Control Buttons Control buttons Audible Buzzer LCD Overview Icons for navigation keys Navigation KeysUPS System Information Description of items in UPS system window LCD Menus and Data Items Descriptions of UPS menus and data window items Start/stop LanguageTests Language Selection Current Date and Time Set date and time UPS Status Messages Current status and history log records Types of LCD Screens 10.12.2Default Screen10.12.1Opening Display 10.12.3UPS Help Screen 10.12.4Screen Saver Window Pop-Up Windows Liebert NX Operating Modes UPS operating modes UPS Startup Startup ProcedureCircuit Breakers Indicator State Switch from Normal Mode to Bypass Mode Switch from Bypass Mode to Normal Mode Operating Instructions Operating Instructions Energize Nx 480 with Bypass Distribution Cabinet BDC Auto Restart Emergency Shutdown With EPO 11.10.1Battery Undervoltage Pre-Warning Battery ProtectionMulti-Module System Procedures 11.10.2Battery End-of-Discharge EOD Protection 103 11.11.2Inserting One Module into a Multi-Module System LED Function Status Commissioning a Parallel System 11.11.3Shutdown Procedure-Complete UPS and Load ShutdownParallel System Startup Analog Input Interface Power OutputCommunication and Other User Terminals Liebert IntelliSlot Communication Liebert NX communication options Configuring Baud RatesSee 12.1.5 Configuring Comments Relay Card Liebert IntelliSlot Web card display Replacing Dust Filters Remote Alarm MonitorLBS Mode-Load Bus Synchronization MultiPort 4 Card Battery In-lb N-m Torque specificationsBattery torque rating Lug Size and Torque Requirements Distance to connection points on the Liebert NX UPS Cable Lengths Floor to Connection Point Inside UPSParallel system current table External cabinet dimensions, including side panels Cable size and tightening torques 113 Battery Run Times Enersys battery run times in minutes D Dynasty battery run times in minutes Specifications and Technical Data 116 UPS status messages Event Message Description / Suggested Action if any 118 119 120 121 Twor k Ne tIs t Care