Extron electronic ISM 824 manual

Operation and Setup, cont’d

Select Output submenu

This menu allows selection of any configurable Video Scaler outputs installed to be configured using further submenus. To select an output to configure, do the following:

1.	From the top level (Output Card Configuration) menu, press Next to enter
	the first submenu level (Select Output). The last selected scaler card output
	button and its associated input button lights green, and the LCD indicates the
	selected output.
2.	If configuration of another output is desired, press that output button to select
	it. The LCD shows the new selection, and the corresponding buttons light.
3.	Proceed to the rest of the submenus to configure the selected output.

Output Config submenu

Within this submenu, the resolution, the refresh rate, the output signal type, and the sync polarity can be selected and adjusted.

1.	From the Output Config. submenu press Menu.
2.	Press Next to bring up the Resolution submenu. In this submenu, the
	resolution and refresh rate can be adjusted.

NThere are 19 output resolutions to choose from (640 x 480 at 50 Hz through 1080p at 60 Hz). The refresh rate is dependant on the resolution selected. See the resolution/refresh rate table below.

Resolution	50 Hz	60 Hz	72 Hz	96 Hz	100 Hz	120 Hz

640x480	X	X

800x600	X	X

852x480	X	X

1024x768	X	X

1024x852

1024x1024

1280x768	X	X

1280x1024	X	X

1360x765	X	X

1365x768	X	X

1366x768	X	X

1365x1024	X	X

1400x1050	X	X

1600x1200

480p		X

576p	X

720p	X	X

1080i	X	X

1080p	X	X

Figure 3-49 — Video Scaler output resolution/refresh rate table

Rotate the left front panel encoder ([) to adjust the resolution value, and rotate the right encoder ({) to adjust the refresh rate.

3. Press Next for the next submenu, Output Type. Within this submenu the output signal type (RGBHV, RGBS, RGsB, YUV Bi-Level) can be selected.

Rotate either front panel encoder to select the output signal type.

3-38 ISM 824 Integration Scaling Multiswitcher • Operation and Setup

Image 70

Extron electronic ISM 824 manual Video Scaler output resolution/refresh rate table

Contents

Integration Scaling Multiswitcher ISM Sicherheitsanleitungen Deutsch Safety Instructions EnglishConsignes de Sécurité Français Instrucciones de seguridad Español ISM 824 Integration Scaling Multiswitcher FCC Class a Notice Ii ISM 824 Integration Scaling Multiswitcher ISM 824 Integration Scaling Multiswitcher Quick Start QS-1 Pass-through outputs Connect video QS-2 ISM 824 Integration Scaling Multiswitcher Quick Start Quick Start ISM 824 Integration Scaling MultiswitcherMaking input to output ties ISM 824 Integration Scaling Multiswitcher Quick Start QS-3 Picture adjustmentsPresets OUT #5 ISM 824 Menu System Front panel security lockout Executive modeQS-4 ISM 824 Integration Scaling Multiswitcher Quick Start Menu button The Menu Table of Contents Table of Contents, cont’d Page Table of Contents, cont’d Sys tems s ettings page IP Settings fields Rev. a One ISM 824 Integration Scaling Multiswitcher Introduction About the Integration Scaling MultiswitcherAbout this Manual Typical ISM 824 application Introduction, cont’d Definitions Outputs FeaturesInputs Tie any input to any or all outputs Optional Output Card Features Universal Scaler card ISM RGB Dual Output Wideband card ISM 2WB Video Scaler card ISM VSSingle Output Wideband card ISM 1WB Introduction, cont’d Two Important safety instructions Installationstallation, cont’dUL/Safety Requirements ISM 824 Integration Scaling Multiswitcher Installation UL requirements for rack mounted devices Mounting the SwitcherTabletop placement Rack mounting Rear Panel Features and Connection Installation, cont’dPower and control connections Choosing a network cable Cabling and RJ-45 connector wiringTerminating the network cable Input connections Input connections for various video formats Output connections Balanced Stereo Output Video output connections Optional output card connectionsAudio output connections Place Installing the optional output cardsIf applicable, repeat for any other output cards Cover Three Front Panel Features Input and output buttons Control selection buttons These four buttons Control buttonsEnter button The Enter button flashes green Operation and Setup, cont’d Default display cycle Powering UpLCD begins the default display cycle Video only green Front Panel OperationMaking input to output ties Green video only An example of creating a set of video and audio ties Press and release the Enter button figure Viewing ties Press the View button lights red Adding ties to existing ties Press and release the Esc button see -8. The View button Press View and observe the LCD display see figure Removing tiesPress and release the Esc button see -12. The View button Press Esc to clear View and reset the LCD Another video input can now be tied to outputs 2 Replacing ties Press and release the Esc button see -16. The View button View V=7-22-3-- Ties A=2388-33 Input/Output grouping 10001010 An example of creating a set of I/O groups VI EW V=7-22-3 Press Esc to clear all pending changes and reset the LCD=2388-33 Muting an output Viewing the RGB delay Viewing and setting the RGB delayUnmuting an output OUT #3 RGB Delay Changing the RGB delay Viewing input audio level and output audio volume Input audio level gain and output audio volumeGain = Adjusting input audio level and output audio volume See -26. The range is -18 dB to +24 dB Saving a preset PresetsOverview Save Preset #11 Recalling a preset Brightness Picture adjustmentsColor/Tint Contrast Adjusting the picture color/tint Adjusting the picture brightness/contrast Press the Esc button to clear all button and reset the LCD Adjusting the picture detailBRT OUT #5 Adjusting the picture size Adjusting the picture positionCurrent size setting see -37 for that output Adjusting the picture zoom =1024 Background illumination settings Front panel security lockout Executive modes 40 Executive Mode 2 initiation and exit method ISM 824 Menu System Auto Image menu Input configuration menu Input Conguration Output card configuration menu Universal Scaler configuration menu ScalerUniversal Right encoder to adjust the V line value Input Setup submenuTo adjust the H pixel value, and rotate Select Output submenu Output Config submenu Output Configuration Scaler boards User Presets submenu Press Next to return to the upper level Output Config. menuPress Menu to go to the next submenu User Presets Press Next to return to the User Preset menu Split Grayscale Advanced Config submenuSplit Color Bars Aspect ratio Default ISM 824 Integration 49 Video Scaler output resolution/refresh rate table Within this submenu, up to 3 presets can be saved or erased User PresetsAdvanced Config Adjusted. Default setting is View Comm Settings menu Input Editing the communication settings Exit menu System Reset MenuScreen. Use this menu to exit from the device Resetting the Unit with the Reset Button Reset Mode Comparison Summary Four Pin Front Panel Configuration PortRS-232/RS-422 Link RS-232 Function RS-422 Ethernet Link SymbolsDefault address Ethernet connection SIS Programming and Control, cont’d ISM 824 specific symbol definitionsX5 = Input selection Switcher-Initiated MessagesPower-up Input and output video type Auto Image ReconfigAuto Memory Switcher Error Responses Host-to-Switcher InstructionsUsing the Command/Response Tables Control, cont’d Command/Response Table for SIS CommandsProgramming OutX@ InX! RGB RprX4 @ $TypX!*X# SprX4 @*0B @*1B@Vmt1 @Vmt0 X! ...Vid X5! X5! X5Mut X5! X5! X5 Vgp X4Out*X! X \X\X\X\ Inf X\X\X\X\\ X\ X\ Programming and Control Front panel lockout executive mode Multiswitcher SISX4*,X4 @*X$ @%2AX$ @HstX!*X$ ZpgX4ZpxX5 @*X% @%2AX% @VstX!*X% 13*X@*X # 12*X@*X* #@ApxX!*X @AlnX!*X @+Y @BrtX!*X1% @*X1% @%2AX1% @ConX!*X1%@*X1%Y @%2AX1% Y @BrtX!*X1% @-Y @BrtX!*X1% X1*X1*X1&*X1 @ZomX!*X5$*X1&*X1EscX@,X1*X1*X1&*X1&XY WX@,X1%2AX1%2AX1 @*X2!*X2@ = @%2AX2!%2AX2@ = RteX@*X2!*X2@ @SprX@*X2 @*X2@RprX@*X2 @*X2% @%2AX2% @RprX2% @*0M Video Scaler ISM VS Output@*1M @ImgX @HszX!*X1 @VphX!*X1@VszX!*X1 @Pol X\ @*X2!*X2@ =@*X\# @*X2% @Blu1 @FlmX@ Frz1 16*X@*X1# @ImgX! *0 @*X1% @%2AX1% @BlbX!*X1%@ImgX! *1 Bottom blanking X7 = Command/Response Table for IP SIS CommandsSymbol definitions X7$ = X7# IpnX7IptX7@ IpzX7$ X8#,X8$ X8@EX8!,X8#,X8$,X8$, ... X8$EM X8$ Five ISM 824 Windows Control Program Installing the softwareInstallation from the CD-ROM Extron software CD window appears figure Installation from the Web site Download Center Web Using the software ISM 824 Multiswitcher Software, cont’dIf connecting by TCP/IP If connecting by RS-232 Extron ISM 824 Control Program main window -5 appears File Menu featuresControl program menus and pages Tools Data tracer window 10 ISM 824 I/O Group Settings menus − all groups cleared 11 ISM 824 I/O grouping completed 13 ISM 824 Unit Settings menus − IP and RS-232 windows Window Extron Firmware Loader appears 15 Firmware Loader window with selected firmware file Help ISM 824 Windows Control program Creating a tie Select the Video/audio mode Follow all or BreakawayRemoving a tie Muting or unmuting output signals 20 Output video and audio signal muting 22 Recalling a preset Settings Configuring the input video signal type Creating or editing input and output names Setting the RBG delay Audio Settings Adjusting the output volume level Adjusting the input gain and attenuationPress Enter. The output’s volume is set to that level Output Cards Create an input to output tie Selecting an aspect ratio Making picture adjustmentsSelecting a test pattern Recalling an input preset Saving or recalling user presetsSaving input presets Deselecting or re-selecting auto memory Starting auto image Freezing an image Making input to output ties Setting top and bottom blanking values Recalling an input preset Using the Button Label Generator software Button Label Generator Replacing the button labels 34 Remove the button cap to replace the label ISM 824 Multiswitcher Software, cont’d Html Operation Downloading the Startup To access the ISM 824 using Html pages do the followingISM 824 Integration Scaling Multiswitcher Html Operation Start the Web browser program System Status System Status Html Operation, cont’d Configuration PagesSystem Settings page IP Settings fields Unit Name field Gateway IP Address field Dhcp radio buttonsIP Address field Subnet Mask field ISM Settings System Settings page Date/Time Settings fieldsClick the desired value Input configuration RGB delay Executive mode PasswordsEmail Alerts Click Edit. The Edit button changes to Save Setting up e-mail alertsSetting up Smtp authorization Eml extension that contains the message Firmware Upgrade Both a user name and a password must be specified Click the Firmware Upgrade link see figure Access the ISM 824 using Html pages as described onClick the Configuration tab Port File Management Enter the new directory name in the Dir/ field Control Pages User Control 12 Click in an output field to see the drop down list 13 A/V mute buttons status according to signal type 14 I/O Presets Universal Scaler ISM RGB Slot output card configurationEach configurable card has its own For the Universal Scaler is shown below User and input presets can be saved and/or recalled Video Scaler ISM VS For the Video Scaler is shown below Special Characters Space spaces are accepted in names + ~ , @ = ‘ ’ semicolon AAppendix a Ethernet Connection Ping to determine Extron IP address Connect as a Telnet client Ping to determine Web IP address Open Ethernet Connection, cont’dTelnet tips Escape character and Esc key Close Local echoSet carriage return-line feed Quit Local and remote devices Subnetting a PrimerGateways IP addresses and octets Unmasked octets are compared indicated by ? in figure A-6 Determining whether devices are on the same subnetMasked octets are not compared indicated by X in figure A-6 Ethernet Connection, cont’d AppendixBB Specifications ReferenceInformation,co t’d 50 Hz, 60 Hz, 72 Hz, 96 Hz, 100 Hz, or 120 Hz Vp-p for Y of component videoTo 1.0 Vp-p Scaled RGBHV, RGBS, RGsB, HD digital component video YUV Reference Information, cont’d Gateway = Extron’s control/configuration program for WindowsARP, Icmp ping, TCP/IP, Telnet, Http Dhcp = off ISM 824 part number Part Numbers and AccessoriesAccessories Included parts Asia Japan Japan Extron Electronics. All rights reserved