D-160 Owner's manual (SETUP mode)

2. How to set each Mode

2-1. Track Swapping ("Track Exchange?")

 

This mode allows you to swap a mono track with one of the other recorded tracks, e.g.

 

swapping track 1 with track16. Mono track swapping can be done on any two tracks

 

from track 1 to track 24 including the additional tracks.

 

The mode also allows you to swap 8 real tracks with 8 additional tracks at once. In this

 

case, you can either swap tracks 1 ~ 8 with tracks 17 ~ 24 or tracks 9 ~ 16 with

tracks 17

~ 24.

<Note>

You can only swap tracks within a program. It is not possible to swap tracks between different programs.

1.Press the DISP SEL key and choose the flashing SETUP mode on the display.

Then, press the EXECUTE/YES key. The SETUP display will stop flashing.

2.Choose "Track Exchange?" with the JOG dial. The "?" display will start flashing.

3.Press the EXECUTE/YES key.

You have arrived at the second step of the "Track Exchange?" menu.

The display will now show "Trk=01<->Trk=01" in the current program as in the figure below.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SETUP

OL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

44.1kHz

9

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

12

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

18

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

24

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

30

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

42

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

_

1

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

 

4.Use the JOG dial to enter the track you want.

Then, use either the HOLD/> key or SHUTTLE dial to move the flashing track number so that you can choose another track.

For example, If you choose "02" on the left hand side "Trk=**" and "08" on the right hand side, it means you are swapping Track 2 with Track 8.

Even if you chose the numbers the other way round, i.e. Trk=08<->Trk=02, the result would be the same. In the case you want to swap 8 tracks with the additional tracks, you can choose either Trk=1-8<->Trk=17-24 with the left hand side "Trk=**" flashing on the display or Trk=17-24<- >Trk=9-16 with the right hand side "Trk=**" flashing on the display. because these 8 track settings are situated between Track 24 and Track 01, find them by rotating the JOG dial.

5.Press the EXECUTE/YES key after you have chosen the two tracks you want.

The display will now show "Exchange 02 <-> 08" and be flashing "SURE?".

6.Press the EXECUTE/YES key once again to proceed.

After swapping the recorded data on track 2 with one on track 8, the display will show "COMPLETED!". Then go back to the normal time base display as before you entered SETUP mode.

142

Page 142
Image 142
Fostex D-160 How to set each Mode, Track Swapping Track Exchange?, 142, Use the JOG dial to enter the track you want