143 | Fujitsu BX600 S2 specs

Power Supply Concept

Power Supply Units

a

Figure 91: Disengaging the power supply unit (a = green touch point)

ÊPress the locking button (a) to disengage the locking mechanism of the PSU handle.

PRIMERGY BX600 S2 Basic Unit

143

Image 143

Fujitsu BX600 S2 manual 143

Contents

Primergy BX600 S2 Basic Unit Certified documentation according to DIN EN ISO Comments… Suggestions… Corrections…Copyright and Trademarks Contents Contents Contents Power Supply Concept Introduction Additional server documentation Overview of the DocumentationOverview of the Documentation Concept and Target Group of this Manual Further Sources of Information Introduction Communication interfaces FeaturesFeatures Server capacity Management blade Ethernet LAN Pass-Thru-Blade High Level of Availability and Failure Protection Power SupplyKVM-Blade Ventilation ServerStart Service and SupportServer Management Notational Conventions Notational Conventions Technical Data Mechanical Values Technical DataWeight Noise Level Environmental ConditionsPage Overview Basic Unit Installation Steps Overview Basic Unit Installation Steps Important Notes Before Setting Up Important Notes Other Important Notes Batteries CE Certificate Components With Electrostatic-Sensitive Devices FCC Class a Compliance Statement FCC Class a Compliance Statement Transporting the Basic Unit Important Notes Environmentally Friendly Product Design and Development Environmental Protection Environmental Protection Local Contacts Returning BatteriesPage Installing the Hardware Installing the HardwareInstallation Steps Unpacking the Basic Unit Unpacking the Basic Unit PRIMECENTER/DataCenter Rack Installing the System in the RackRequirements of the Rack 3rd-Party Rack Installing the System in the Rack Mechanical conditions Primergy BX600 S2 Basic Unit Mounting the support brackets Mounting the Assembly Kit Repeat the procedure with the second support bracket Mounting the basic unit Mounting/Removing the Basic Unit Connecting External Devices Connectors on the back of the basic unit Connecting External Devices PCI Cards with Cable at the Front Cable Routing Connecting External Devices Installing the Hardware Disconnecting Cables Instructions on Connecting and Disconnecting CablesConnecting Cables Connecting the System to the Mains Connecting the System to the Mains Connecting the System to the Mains Page Primergy BX600 S2 basic unit Primergy BX600 S2 Basic Unit Preparation for Use and Operation System power ON/OFF button Operating and Indicator Elements of the Basic UnitOperating and Indicator Elements Power indicator bicolor LED Front identify button Front identify/Fault indicator amber LEDPreparation for Use and Operation Rear identify button1 Rear identify/Fault indicator green LED1Rear Switching OFF the Basic Unit System is Powered on Switching the Basic Unit ON/OFFSwitching on the Basic Unit Basic Unit is Powered OFF Specified switch-ON time/switch-OFF time Switching the Blade Server ON/OFFAfter power failure Switching the Server Blades ON/OFF Cabling the System Management Blade ConfigurationPre-Configuration Requirements Initial Configuration via Serial Connection to Client Log in as root. The initial password reads root Management Blade Configuration Enter 1 to call up the Management Agent Information menu Management Agent Information menu Agent NIC Duplex Mode menu Proceed as follows Updating the Server Blade Firmware Bios and BMCUpdating System Components Updating the server blade Bios via the web interface Updating the server blade BMC via the web interface Updating the Management Blade Firmware Updating the management blade firmware via the web interface Updating the Switch Blade Firmware  Press Ctrl-Q Return Console Menu Removing an operation code image file Click Transfer from Server Page Preventing Unauthorized Boot Process Bios Setup Security FunctionsPreventing Unauthorized Bios Setup Calls Preventing Unauthorized System AccessPage Server Blades Page Server Blades Installation Sequence Configuration Diagram for 2-way Server Blades Installation Sequence Server Blades Installation sequence for 4-way server blades Configuration Diagram for 4-way Server Blades Removing the Dummy Module Adding a Server Blade to the Basic Unit Adding a Server Blade to the System Inserting the Server Blade Adding a Server Blade to the System Server Blades Inserting the server blade Final engaging of the locking mechanism Removing the Server Blade Ethernet LAN Switch Blades LAN Switch Blade SB9 6x1Gbit Gbit Ethernet LAN Switch Blade SB9 6x1Gbit LAN Switch Blade SB9 6x1Gbit Ethernet Switch Blades LAN Switch Blade SB9 6x1 Gbit + 2x10 Gbit Gbit Ethernet LAN Switch Blade SB9 6x1 Gbit + 2x10 Gbit CX4 link/active indicator green LED Cisco Catalyst Blade Switch Cisco Catalyst Blade Switch Ethernet Switch Blades Gbit Switch Blade 10/2 10 Gbit Switch Blade 10/2 Bedien- und Anschlussfeld ID indicator green LED Port Assignment of the LAN Switch Blades Port Assignment of the LAN Switch Blades Configuration with Ten 2-way Server Blades Configuration with Five 4-way Server-Blades Vcaution Installing a LAN Switch Blade Removing the dummy module a = green touch point Installing a LAN Switch Blade Inserting the LAN Switch Blade Disengaging the switch blade Removing the Switch Blade Page Ethernet LAN Pass-Thru-Blade Ethernet Pass-Thru Blade Control and Connection Panel RJ45 connectorsLAN activity indicator orange LED Control and Connection Panel Port Assignment of the Gigabit Ethernet Pass-Thru Blades Slots for installing pass-thru blades Ethernet port assignment with ten 2-way server blades Port Assignment Configuration with Five 4-way Server Blades Replacing an Ethernet Pass-Thru Blade Fibre Channel Switch Blade Fibre Channel Switch Blade FC switch blade status display 2-color LED IThe LED might also blink while testing 107 NET4 NET3 Port Assignment Fabric port assignment with 2-way server blades FC Switch Blade Fabric port assignment with five 4-way server blades Fabric port assignment with 4-way and 2-way server blades FC switch blade installationPage Fibre Channel pass-thru blade Fibre Channel Pass-Thru Blade 114 Inserting a Fibre Channel SFP module Fibre Channel SFP module Removing an SFP Module Fibre Channel SFP module Slot numbering for the Fibre Channel pass-thru blades Port Assignment of the FC Pass-Thru Blades Slot numbering for the SFP modules FC Port Assignment 119 120 Removing the FC pass-thru blade Exchanging an FC Pass-Thru BladeFC Pass-Thru Blade Exchanging an FC Pass-Thru Blade 123 Page Management blade slots Management Blade LAN link indicator green LED Lights green The LAN is linked Serial port connector Master indicator green LED LAN active indicator amber LEDI2C connector Failure indicator amber LED Exchanging the Battery Exchanging the Battery 129 Removing the Management Blade Exchanging a Management BladeExchanging a Management Blade 131 Removing the management blade KVM Blade Standard Version KVM Blade Control Panel of the KVM Blade Standard Version ID/error LED green LEDKVM connector KVM Blade Standard Version Control Panel of the Adv. KVM Blade 13.2 Adv. KVM BladeKVM Blade Adv. KVM Blade Rear ID/error LED green LEDLAN activity indicator green LED LAN connection indicator orange LED Digital KVM Blade Control panel of the digital KVM blade Power indicatorID indicator Digital KVM Blade PSU4 PSU3 PSU2 PSU1 Power Supply Concept Power Supply Units Power Supply Units On/off display green LED Power Supply ConceptFault display amber LED Mains power supply display green LED Replacing a Power Supply Unit 143 Removing the power supply unit Removing the PSU Adding a Power Supply Unit PSU dummy module 147 Page FAN1 FAN2 Ventilation Concept Fan 1 LEDs Fan 2 LEDs Fan condition Fan UnitFan Unit Ventilation Concept Replacing the Fan Unit Removing the fan unit Replacing a Fan in the Unit Page Power supply overloaded Troubleshooting and TipsSystem Power LED Remains Unlit Wrongly connected power cables One of the fans in the rear fan modules has failed Front or Rear Identify/Fault LED Blinks AmberOne of the power supply units fails Switch blade fails Screen Remains Dark System Switches Itself OFF No Mouse Pointer Displayed On the Screen Flickering Stripes on the Monitor ScreenNo Screen Display or Display Drifts Defective Drive Server Blade Does Not BootFloppy Disk Cannot Be Read/Written Time and Date Are Not Correct Added drive is identified as defective Defective Drive Abbreviations Abbreviations NMI USB Primecenter Rack Safety Ergonomics Warranty DataCenter RackRelated Publications 166 167 Page Adding BatteryIndex Index Indicators LED Unpacking LAN Hinweise zum vorliegenden Dokument Information on this document