![](/images/backgrounds/292484/hp-hp-laserjet-cp4025dn-laser-printer-cc490a-users-manual-545063217x1.png)
Table
Description | Recommended action |
|
|
TRAY <X> [TYPE] [SIZE] | This message states the current type and |
To change size or type press OK | size configuration of the tray. |
| |
To accept settings press |
|
To change size or type press the OK button. To accept settings press the back arrow .
TRAY <X> EMPTY [TYPE] [SIZE] | The specified tray is empty and the current | Refill the tray at a convenient time. | |
| job does not need this tray to print. |
|
|
|
|
| |
TRAY <X> OPEN | The specified tray is open or not closed | Close the tray. | |
| completely. |
|
|
|
|
| |
TRAY <X> OVERFILLED | The tray is filled above the | Remove enough paper so that the paper | |
Remove some paper | marking. | stack does not exceed the limit for the tray. | |
|
|
| |
|
|
| |
TRAY <X> SIZE = <Size> | The product is set to print on a small paper | To use this size paper, install the media insert | |
Media insert required in tray | size that requires the HP postcard media- | before loading the paper. See Load paper | |
insert to be installed in this tray. | |||
|
| If you do not have the HP postcard media | |
|
| insert, 100 x 150 mm (4 x 6 in) paper can be | |
|
| printed from Tray 1 without the insert. | |
|
|
| |
TYPE MISMATCH IN TRAY X | The specified tray contains a paper type that | The specified tray will not be used until this | |
| does not match the configured type. | condition is addressed. Printing can continue | |
|
| from other trays. | |
|
| 1. | Load the correct paper in the specified |
|
|
| tray. |
|
| 2. | Verify the type configuration. |
|
|
| |
UNABLE TO COPY JOB | The product does not have enough memory | Add more memory to the product. See Install | |
| to produce multiple original prints of this job. | ||
| One copy will be printed. |
|
|
|
|
| |
UNABLE TO STORE JOB | A job cannot be stored because of a memory | Install additional memory in the product. | |
| or configuration problem. |
|
|
|
|
| |
Unsupported data on [FS] DIMM in slot x | The data on the DIMM for the indicated file | Press the OK button to clear the message. | |
To clear press OK | system is not a type that the product supports. | Replace the DIMM. See Install memory | |
[FS] can be either a ROM or Flash file system. | |||
|
| ||
|
|
| |
UNSUPPORTED DRIVE INSTALLED | A | Turn off the product, remove the hard drive, | |
| installed. | and then turn on the product. | |
|
|
| |
UNSUPPORTED SUPPLY INSTALLED | The print cartridge is for a different HP | If print quality is no longer acceptable, replace | |
To continue press OK | product. | the print cartridge. | |
|
|
|
For a list of supported print cartridges, see
USB ACCESSORIES EXCEED POWER | A USB accessory is drawing too much |
LIMIT | electrical current. Printing cannot continue. |
Remove the USB accessory, and then restart the product.
Use a USB accessory that uses less power or that contains its own power supply.
USB ACCESSORY ERROR | This message appears when a connected |
| USB accessory draws too much power. |
| When this happens, the ACC port is disabled |
| and printing stops. |
Remove the USB accessory, and then restart the product
Use a USB accessory that uses less power or that contains its own power supply.
ENWW | Interpret |