Table 2-1Embedded Jetdirect menu (continued)

Item

Sub-item

Sub-item

Sub-item

Description

 

 

 

 

 

 

 

SNMP TEST

YES

This test checks operation of SNMP

 

 

 

NO*

communications by accessing predefined

 

 

 

SNMP objects on the product.

 

 

 

 

Select YES to choose this test, or NO to not

 

 

 

 

choose it.

 

 

 

 

 

 

 

DATA PATH TEST

YES

This test helps to identify data path and

 

 

 

NO*

corruption problems on an HP postscript level

 

 

 

3 emulation product. It sends a predefined PS

 

 

 

 

file to the product, However, the test is

 

 

 

 

paperless; the file will not print.

 

 

 

 

Select YES to choose this test, or NO to not

 

 

 

 

choose it.

 

 

 

 

 

 

 

SELECT ALL

YES

Use this item to select all available embedded

 

 

TESTS

NO*

tests.

 

 

 

Select YES to choose all tests. Select NO to

 

 

 

 

 

 

 

 

select individual tests.

 

 

 

 

 

 

 

EXECUTION TIME

 

Use this item to specify the length of time (in

 

 

[H]

 

hours) that an embedded test will be run. You

 

 

 

 

can select a value from 0 to 24 hours. If you

 

 

 

 

select zero (0), the test runs indefinitely until

 

 

 

 

an error occurs or the product is turned off.

 

 

 

 

Data gathered from the HTTP, SNMP, and

 

 

 

 

Data Path tests is printed after the tests have

 

 

 

 

completed.

 

 

 

 

 

 

 

EXECUTE

YES

NO: Do not initiate the selected tests.

 

 

 

NO*

YES: Initiate the selected tests.

 

 

 

 

 

 

PING TEST

 

 

This test is used to check network

 

 

 

 

communications. This test sends link-level

 

 

 

 

packets to a remote network host, then waits

 

 

 

 

for an appropriate response. To run a ping

 

 

 

 

test, set the following items:

 

 

 

 

 

 

 

DEST TYPE

IPV4

Specify whether the target product is an IPv4

 

 

 

IPV6

or IPv6 node.

 

 

 

 

 

 

 

 

 

 

 

DEST IPV4

 

Type the IPv4 address.

 

 

 

 

 

 

 

DEST IPV6

 

Type the IPv6 address.

 

 

 

 

 

 

 

PACKET SIZE

 

Specify the size of each packet, in bytes, to

 

 

 

 

be sent to the remote host. The minimum is

 

 

 

 

64 (default) and the maximum is 2048.

 

 

 

 

 

 

 

TIMEOUT

 

Specify the length of time, in seconds, to wait

 

 

 

 

for a response from the remote host. The

 

 

 

 

default is 1 and the maximum is 100.

 

 

 

 

 

 

 

COUNT

 

Specify the number of ping test packets to

 

 

 

 

send for this test. Select a value from 0 to 100.

 

 

 

 

The default is 4. To configure the test to run

 

 

 

 

continuously, select 0.

 

 

 

 

 

ENWW

Control panel menus 37