IP configuration, Remote logging, 101 | Intel SBCEFCSW, SBFCM

✏NOTE

The Read Community, Trap Community, and Write Community settings are like passwords; therefore, they are write-only fields. The current settings are not displayed.

Figure 16. Network Properties window

IP configuration

The IP configuration identifies the switch module on the Ethernet network and determines which start (boot) method to use. Start methods described in the following table are for external and internal ports. Table 23 describes the IP configuration parameters.

Table 23. IP configuration parameters

Parameter	Description

IP address	Internet protocol (IP) address for the Ethernet port.
	Note: When the Blade Server Chassis SBCE is turned on, the management module
	loads the following factory default Ethernet IP addresses:
	• Switch module bay 3: 192.168.70.129
	• Switch module bay 4: 192.168.70.130

Subnet mask	Subnet mask address for the Ethernet port. The default value is 255.255.255.0.

Boot method	Static - Uses the IP configuration parameters entered in the Switch Properties window.

Gateway	IP gateway address. The default value is 10.90.90.254.

Remote logging

The Remote Logging (syslog) feature enables saving of the log information to a remote host that supports the syslog protocol. When enabled, the log entries are sent to the syslog host at the IP address that you specify in the Logging Host IP Address field. Log entries are saved in the internal switch module log whether this feature is enabled or not.

101

Image 115

Intel SBCEFCSW, SBFCM manual Remote logging, 101, IP configuration parameters

Contents

Page Disclaimer Iii Safety and regulatory information Electrical Safety General Safety Handling electrostatic discharge-sensitive devices Safety compliance Regulatory specifications and disclaimers Electromagnetic compatibility notice USA Electromagnetic compatibility EMCVii Japan EMC Compatibility Electromagnetic compatibility notices International RRL Korea English translation of the previous notice Contents Xii Xiii Diagnostic informationSymptom-to-FRU index Intel Server FC Expansion Card Sbfcm Getting help and technical assistance Sbcefcsw / Sbfcm Parts listing Related publications General informationPage Intel Blade Server Fibre Channel Switch Module Sbcefcsw Logging on to a switch Command line interface CLI Command Command syntaxCommands Command syntax is as follows User authority commands Admin authority command Commands listed by authority levelAdmin session commands Keywords Admin commandAuthority Syntax Alias command Rename aliasold aliasnew Remove alias members Config command Examples Date Date commandAdmin to change the date user to display the date Following is an example of the Date command Following is an example of the Fallback command Fallback commandFallback Help Help commandAll Following is an example of the History command History commandHistory Fetch accountname ipaddress filesource filedestination Image commandCleanup Image Lip Lip command for external ports onlyPortnumber Passwd Passwd commandAccountname Displays current blade server process information Ps commandFollowing is an example of the Ps command Syntax Examples Reset command Quit command Port configuration defaults Switch configuration defaultsParameter Default Threshold configuration defaults System configuration defaults Snmp configuration defaults Set command Offline Switch stateDiagnostics Online Set Config port parameters Set Config commandSet config Switch Threshold Zoning ISL Set Config switch parameters Threshold Set Config threshold parameters Following is an example of the Set Config Port command Set Config zoning parameters Following is an example of the Set Config Threshold command Following is an example of the Set Config Switch command Following is an example of the Set Config Zoning command Set Log command Level level Set Port command Snmp System Set Setup commandSet setup Snmp configuration settings Following is an example of the Set Setup Snmp command System configuration settings Following is an example of the Set Setup System command About Show commandAlarm Show Interface DomainsDonor Fabric LIPF8F7 Show Port parameters Displays the Post log which contains results from the Post Post logSupport Users TopologyVersion Following is an example of the Show Port command Following is an example of the Show Topology command LIPF8F7 Following is an example of the Show Switch command Show config Show Config command Following is an example of the Show Config Threshold command Following is an example of the Show Config Switch command Following is an example of the Show Config Zoning command Show Log command Following is an example of the Show Log command Byte Show Perf commandShow perf Byte Inbyte Following is an example of the Show Perf command Show setup Show Setup commandMfg Following is an example of the Show Setup System command Shutdown Shutdown command Test command Choose one of the two types of port loopback tests to run Following is an example of the Uptime command Uptime commandUptime Add User commandUser Accounts Following is an example of the User List command Following is an example of the User Delete command Following is an example of the Whoami command Whoami commandWhoami Zone command Type zone zonetype Members zoneRemove zone members Rename zoneold zonenew Following is an example of the Zone Zonesets command Following is an example of the Zone Members command Zoneset command Rename zonesetold zonesetnew Remove zoneset zonelistZones zoneset Opens a Zoning Edit session Zoning commandActive Cancel Clear Edit History Limits List Restore Save Edit Following is an example of the Zoning List command Following is an example of the Zoning Edit commandPage SAN Utility user interface Using the SAN Utility Faceplate window Menu bar Toolbar buttons ToolbarSome menu selections have shortcut keys as shown in Table Menu shortcut keys Graphic window Fabric treeData window and tabs Fibre Channel switch module and link status indicators Using the Topology windowWorking status indicator Fibre Channel switch module and link status Arranging switch modules in the window Working with switch modules and links Selecting switch modules and links Using the Faceplate windowTopology data window tabs Selecting ports Opening the Faceplate window and pop-up menusPort views and status Working with ports Opening pop-up menus Setting up securityManaging fabrics Faceplate data window tabs Removing a fabric Managing the fabric databaseAdding a fabric Click Add fabric Saving a fabric view file Adding a new switch module to a fabricFor switch module bay Opening a fabric view file Fabric status Replacing a failed switch module in a fabricDeleting switch modules and links from the Topology display Displaying fabric information Topology window switch module and status icons Active Zoneset Data window Zoning a fabricZoning concepts Zones Zone sets Zone merge failure Using the Zoning Config windowRestoring default zoning Merging fabrics and zoning Zone merge failure recovery Using the Edit Zoning window Toolbar button Function Managing zone setsFollowing table explains the toolbar buttons and functions Edit Zoning window toolbar buttons Copying a zone to a zone set Creating a zone setClick Edit / Create Zone Set Activating and deactivating a zone set Creating a zone in a zone set Managing zonesRemoving a zone set Removing all zoning definitions Removing a zone from a zone set Adding zone membersRenaming a zone or a zone set Removing a zone member Creating an alias Managing aliasesRemoving a zone from all zone sets Changing zone types Displaying switch module information Managing switch modulesRemoving an alias from all zones Name server data window entries Name Server data window Switch data window entries Switch Data window Fabric view port graphing application Link data window Port Information Data window Configured Zonesets Data windowAlarm Log Data window Port Statistics Data window Configuring alarms Managing alarmsFaceplate window, click Switch / Configure Alarm Thresholds Configuring a switch module Paging a switch moduleSetting the date and time Resetting a switch module Domain ID and Domain ID Lock Switch module administrative states Broadcast support Timeout valuesTimeout values Network properties 101 IP configurationIP configuration parameters Remote logging Activating the fallback firmware Archiving a switch moduleManaging firmware Loading firmware 103 Managing portsDisplaying port information Monitoring port status Port speeds Port mode descriptionsMode Description Port operational states Media icon Description Port graphing and Fabric View application105 SFP module media view Port Statistics Data window entries 107 Port Information Data window entries Configuring ports External Port Properties window 109 Click Port / Port Properties Changing port administrative states 111 Port administrative statesChanging port speeds external ports only Changing port modes external ports only Extending port credits Configuring translated loop TL modes external ports onlyChanging buffer-to-buffer credits external ports only Stream guard Click Port / Reset Port 113 Resetting a port LED diagnostics Switch management utility functions Internal firmware failure LED flash pattern Fatal error LED flash patternHeartbeat LED patterns Normal all pass LED flash pattern Logging Error Switch module fault LED flash patternSwitch module OK LED Configuration file system error LED flash pattern Port isolation causes and fixes Port testingPort fault LED flash patterns 117 Snmp configuration Fibre Channel switch module monitoring using SnmpClick Port / Port Loopback Test Snmp trap configuration parameters Restoring Fibre Channel switch module configurationSnmp trap configuration Snmp configuration parameters Factory default configuration settings Configuration backupConfiguration restore Restoring the factory default configuration Settings Value Port mode GL external F internal Using the Fabric View applicationReinitializing the configuration file system Restoring a switch module Displaying port performance graphs Starting the Fabric View applicationArranging and sizing port performance graphs 123 Customizing port performance graphs Port mapping Mapping port locations and software numberingPort mapping Temperature and altitude Features and specifications125 Blade server on 8% to 80% Blade server off 5% to 80% Expansion Card specificationsType Specification Humidity Major components of the Sbfcm Expansion Card Inventory checklist127 Expansion Card top Installation guidelines Installing the Expansion Card129 Handling static-sensitive devices Installing the Expansion Card 131 Fibre Channel Switch Module LocationsPage O expansion option tray 133Page Keyboard/mouse/video select button 135 Starting Fast!UTIL Using Fast!UTILConfiguration Settings menu options Host Adapter Settings Setting Example Selectable Boot SettingsRestore Default Settings Nonmodifiable expansion card settings and examples Advanced Adapter Settings Advanced Adapter SettingsRaw Novram data RIO options and operation modes Extended Firmware SettingsExtended firmware settings 139 ExitFast!UTIL Scan Fibre Channel devicesFibre Channel disk utility Loopback data test General Checkout General Fibre Channel configuration diagram141 Software problems Hardware problemsSystem configuration problems 143 Fibre channel problemsPage 145 Symptom-to-FRU index 5, 6 Switch error messagesError code Action Fast!UTIL utility status codes 147 Expansion card error messagesMessage Action IP@=XXX.XXX.XXX.XXX Management module error messages 149 Switch diagnostic informationLED error codes I2C diagnostic register definitions Alarms Action Undetermined problemsFailures Action 151 Problem determination tipsPage Option Intel Blade Server Switch Module SbcefcswFibre Channel Switch Module 153 Sbcfm Expansion Card Intel Blade Server Fibre Channel Expansion Card Before you call Using the documentation155