Manuals / NEC / Computer Equipment / Server

NEC 5020M-16, NX7700i SP Command List, The following tables contain SP command lists by category

Models: 5020M-16 NX7700i

1 149

Download 149 pages 48.62 Kb

Page 48

Base Module

2.4.5.4.SP Command List

The following tables contain SP command lists by category:

System Control

	CMD	command name	function	iSP
	CMD	command name	function	state
				state
	DF	Shut down System power	The iSP turns off the DC power of the
		Shut down System power	specified partition without notifying the	m
		(override)	specified partition without notifying the	m
		(override)	SW (OS) even if it is running.
			SW (OS) even if it is running.
			If the specified partition is in S0 state,
	DN	Shut down System power	the iSP only generates the SCI	m
	DN	Shut down System power	(POWBTN). Otherwise, the iSP turns	m
			(POWBTN). Otherwise, the iSP turns
			off the DC power directly.
			The iSP generates the INIT signal to
	DP	System Dump	the specified partition. SW (OS) will	m
			enter its dump routine.
			The iSP turns off the DC power of the
			specified partition without notifying the
	PC	Power Cycle	SW (OS) even if it is running, turns on	m
			the DC power, initializes HW and
			hands off the control to the BIOS.
			The iSP initializes the specified
	RS	Cold Reset System	partition without notifying the SW (OS)	m
			even if it is running.
			The iSP turns on the DC power of the
	UB	Bring up BIOS	specified partition and initializes HW	m
			and hands off the control to the BIOS.
			The iSP turns on the DC power of the
			specified partition and initializes HW
	UP	Bring up System	and hands off the control to the BIOS.	m
			The BIOS will boot the Operating
			System.

“m”: Commands can be executed only on the master iSP.

2-29	855-900549

Image 48

NEC 5020M-16 SP Command List, The following tables contain SP command lists by category, System Control, Base Module

Contents

855-900549-A Rev NX7700i/5020M-16 Operation Manual NEC CorporationDisposing used NECIn the European Union Outside the EuropeanSafety Precautions Handling of the lithium battery Do not touch the internal components of the equipmentDo not insert foreign materials into the equipment Failure processingHandling of the laser product Disposing/collecting/recycling the equipment18kg CAUTIONUse Copper Conductors only ATTENTIONNutilisez que les conducteurs de cuivreATTENTIONMACHINE a FORT COURANT de FUITE 矢印を上に向けて取り付けること。CAUTIONDisconnect input power before removing this cover 注※意：カバーを開ける前に入力電源分電盤切断のこと。ATTENTIONCouper lalimentation electrique avant de demonter ce capot 注※意：保守時は安定板を引き出すこと。保守者の方へ警告 WARNING保守者の方へ警告 WARNING243-304367-GRP MARKINGS243-306629-GRP MARKINGSPreface Rev. 1, MayContents Cleaning SchedulePreventing Accidental Erasure of Data Life of Data Cartridge Tape for the DAT UnitSystem Startup Digital Audio TapeChapter 1 NX7700i/5020M-16 System Overview Figure. External Views of the Cabinet1.1. Configuration and Specifications of the Base Module POWER BAY Figure. Layout of Parts in the Base ModuleNX7700i/5020M-16 System Overview I/O MODULETable. Base Module Specifications Table. Base Module Specifications Cont’d NX7700i/5020M-16 System OverviewMain Cabinet 545Kg1.2. Expandability 1.2.1. Adding Processors1.2.2. Expanding Memory Capacity 1.2.3. Adding CellsFigure. System Configuration Itanium2NX7700i/5020M-16 System Overview Chapter Base ModuleFigure. Doors of Cabinet Base Module2.1. Partition Function Figure. Image of Partitions2.2. Name and Function of Components 2.2.1. Cabinet Primary Cabinet BASE MODULEBASE MODULE POWBAY#12.2.3 Expansion Power Bay 2.2.2 Base Module2.2.4 Cell 2.2.5. I/O Module2.2.6. Power Bay 2.2.7. iSP Figure. Rear panel of iSP Installed in the Base ModuleBase Module 2.2.8. DVD-ROM Unit 2.2.8.1. Loading and Unloading MediaFigure. Loading and Unloading DVD-ROM/CD-ROM 2.2.9. DAT Unit 2.2.9.1. Location of Index Labels2.2.9.2. Notes on Index Labels 2.2.9.3. Preventing Accidental Erasure of Data2.2.9.4. Cleaning the DAT Unit 2.2.9.5. Cleaning Schedule2.2.9.6. Cleaning Medium for the DAT Unit 2.2.9.7. Life of Data Cartridge Tape for the DAT Unit2.2.9.9. Notes on the DAT Unit 2.2.9.10. Loading and Unloading Digital Audio TapesFigure. DAT Units 2.2.10. Notes on Installing the UPS AC SW P1Figure. Jumper Connector for Installing the UPS AC SW CB1 P3AC SW AC SW2.2.11. System LEDs LED CARD2.3. Consoles 2.3.1. SP ConsoleFigure. Console Connection Diagram Base Module2.4. Service Processor SP 2.4.1. Console Connection and Login2.4.1.2. Accessible Console Functions 2.4.1.1. Type of Console Connections2.4.1.3. Console Status and Login Authentication Serial console inoperative Press ESC Choose Exit iSP login prompt Login password requiredCM command Password required2.4.1.4. Login and Main Menu The “backup” indicator will not appear if no backup SP exists Screen Example…BOOT FWiSP BOOT MAIN MENU S iSP commands E Exit Description2.4.2. Note Possible Events including operator entries and System ResponsesBase Module 2.4.3. OS BIOS Console CTRL+BDescription Possible Events including operator entries and System ResponsesBase Module 2.4.4. Virtual SOP Virtual System Operator PanelDescription Possible Events including operator entries and System ResponsesBase Module 2.4.4.1. Details of Partition Status Display Base Module2.4.5. SP Command Console OSBIOS serial console of partition#0 INITIALIZINGBase Module CTRL+B2.4.5.1. SP Command Console Buffer 2.4.5.2. SP Command Prompt2.4.5.3. SP Message Header 2.4.5.4. SP Command List The following tables contain SP command lists by categorySystem Control Base ModuleFigure. System Status Transitions and System Control Commands Configuration Normal mode other commandsSettings Base Module2.4.6. SP Command Reference 2.4.6.1. DF Shut down System Power override FunctionBase Module Description Base Module2.4.6.2. DN Shut down System Power Function2.4.6.3. DP System Dump DP command was accepted. Dump button interrupt will be generated soonFunction Base Module2.4.6.4. DT SP Data and Time Always valid without regard to the current system statusFunction Base Module2.4.6.5. EN Environmental Information 32Way For one or two AC power receiving systemsISPF does not have two AC power receiving systems Always valid without regard to the current system statusBase Module c d e f2-39 The following information will be missing for 8WayBase Module Base Module 2-41Base Module The numbers of PCI Bay cards are changed on 32Way/8Way and ISPFtentative tentativeDescription Base Module2.4.6.6. FV Firmware Versions Always valid without regard to the current system statusFunction iSPyz--- fv ENTER2.4.6.7. HC Hardware Configuration FunctionBase Module Base Module This command is currently not supported Base ModuleBase Module Base Module arg1Base Module Base Module This command is currently not supported Base Modulearg1 arg2This command is currently not supported Base ModuleBase Module Base Module Description of Status Indicator Strings Base ModuleBase Module iSPyz--- hc ENTERHC helpENTER Base Module b c d e2-59 The SM size is shown for the ISPFBase Module 1 LIN=x,y,z x Logical IOX numberz “S” if SCSI SPLIT Mode is selected, and “N” if it is deselected For 32WayHBase Module For 32WayBFor 8Way Base Module For ISPFFor 32WayB, 8Way, or ISPF MMXx2 and MMXx3 are only shown for 32WayBBase Module 2-63Base Module TAG0eTAG0o CELL1Base Module j j j2-65 2 Listed for the PCI Bay in which the Core Cards are installed 3 Listed for the PCI Bay in which the Core Cards are installedBase Module For 32Way, subsequently listed to the max. XBX Card numberBase Module 2-67Base Module POWBAYs Main cabinetPOWBAYs Expansion cabinet For the 8Way/ISPF model, there are three DPSs in Power Bay For the ISPF, Power Bay1 for dual AC systems is not configuredBase Module 2-69Description Base Module2.4.6.8. HE Help Always valid without regard to the current system statusFunction Base Module2.4.6.9. ML Message Log Always valid without regard to the current system statusFunction Base ModuleDescription Base Module2.4.6.10. PC Power Cycle iSP0mINFO.2129 partition 0 handed off the control to BIOSFunction pcENTER2.4.6.11. RS Cold Reset System FunctionBase Module rsENTER2.4.6.12. SG SP/System Setting Setting partition boot method and hot-plug permissionAlways valid without regard to the current system status FunctionBase Module ISPFLAN/Serial SP default FTP Server Configuration SP SNMP ConfigurationBase Module Base Module DescriptionsgENTER bENTERBase Module 2ENTERENTER onENTERDescription Base ModuleBase Module Description Base ModuleDescription Base ModuleBase Module Manager1 LAN0 IPDescription Base Module2.4.6.13. SR Save System CMOS/NvRAM FunctionBase Module file path cmossave/cmos1.bin ENTERDescription DescriptionDescription No 2.4.6.14. UB Bring up BIOS FunctionBase Module mm/dd/yyyy HHMMSS 0------- System initialization started. SPFWRxx.xx2.4.6.15. UP Bring up System This command is valid to inactive partitions DC OffFunction Base ModuleChapter 3 Operation Procedure 3.1. System Startup 3.1.1. System Startup ProcedureOperation Procedure See step 3 in next page Expansion power bay/Base module AC ONSee steps 7 to 11 in next page OS Boot StartRemark Operation Procedure 3.1.2. SP Console Messages Operation ProcedureOperation Procedure 2 Example of SP console screen during system startup3.2. System Shutdown 3.2.1. System Shutdown Procedure Operation ProcedureOperation Procedure See step 6 in next page Turn off AC to expansion power bay/baseStart Shut down OS See step 1 in next page Turn off console PC module See steps 7 and 8 in next page Turn off peripheralsSee 2.2.1 Cabinet for the location of the switch panel. See 2.2.6 Power Bay for the location of the AC switch on the base module and expansion power bay. The number of switches on the switch panel depends on the number of installed base modules and expansion power bays. Take care of the association between these switches and base modules and expansion power bays during switch operation. The switches on the switch panel are used for immediate power shutdown for emergency purposes. When a switch on this panel is turned off, data may be destroyed 3.2.2. SP Console Messages Operation Procedure1 Example of DC power off display on SP console screen 3-103.3. Emergency System Shutdown with AC SW 3.4. AC-LINK Auto ControlData may be destroyed when the AC switch is turned off during Provide criteria for operating the AC switch and use the switchOperation Procedure 1 SP console screen and operation during AC LINK setup= Enable AC LINK and press 3-123.5. OS Boot 3.5.1. OS Boot with Boot Manager Before Installing the OSUse the arrow keys to change settings Use the OS console to operate the EFI Shell. Inputs from the„ Image of the OS Boot screen displayed by the EFI Boot Manager Use the arrow keys to change settingsSLES9 3.5.4. EFI Shell Commands 3.5.3. EFI ShellEFI Shell Commands Operation Procedure CommandDescription Operation Procedure CommandDescription 3.5.5. OS Boot from EFI Shell Operation Procedure Boot the OS loaderfs0¥ cd os fs0¥os ls3.5.6. EFI Devices Computing UID Example 3.5.7. EFI Boot Option Maintenance Boot Maintenance Menu Options Operation ProcedureOption Description3.5.7.1. Boot from a File „ Image of the Boot from a File screenOperation Procedure 3.5.7.2. Add a Boot Option ディレクトリを選択して実行プログ登録できま 3.5.7.3. Add Boot Options 3.5.7.4. Change Boot Order3.5.7.5. Manage BootNext Setting 3.5.7.6. Set Auto Boot Timeout 3.5.7.7. Setting the Network Boot AcpiPNP0A03,0/Pci30/Mac00004C717743Changing procedure 1 Activate the EFI Boot Manager 3.5.7.8. Changing BIOS Settings EFI System Configuration Menu Processor Configuration 3.6. System Dump Chapter 4 Troubleshooting 4.1. Troubleshootingpressing the SHIFT key on the screen Chapter 5 Notes on Handling 5.1. Transportation5.2. DVD-ROM/CD-ROM 5.3. Digital Audio Tape5.4. Cleaning Figure 5-1 Cleaning Locations5.5. Notes on Installation Notes on Handling Memo