Base Module
cmd | arg1 | arg2 | arg3 | arg4 | Description |
check | - | - | - | - | This command is used to check the current |
|
|
|
|
| system configuration focusing on the |
|
|
|
|
| following points: |
|
|
|
|
| • Presence of units with unspecified |
|
|
|
|
| locations |
|
|
|
|
| • Presence of DISABLED components |
|
|
|
|
| • Presence of INVISIBLE units |
|
|
|
|
| This command is always valid without regard |
|
|
|
|
| to the current system state. |
|
|
|
|
| The “DISABLE.” components are not the |
|
|
|
|
| target of this command. |
clear | rowxyy | - | - | - | Use this command to clear the ROW or |
|
|
|
| Directory memory bit error counters. | |
| dirxzz |
|
|
| x is a physical CELL number |
|
|
|
|
| yy is a ROW number |
|
|
|
|
| which must be specified with a |
|
|
|
|
| number. |
|
|
|
|
| zz is a Directory number |
|
|
|
|
| CELL, which must be specified with a |
|
|
|
|
| number. |
|
|
|
|
| This command clears the 3 counters - the |
|
|
|
|
| |
|
|
|
|
| every DIMM and the multibit error counter |
|
|
|
|
| that counts errors for every ROW - at a time, |
|
|
|
|
| along with the page deallocation entry table. |
|
|
|
|
| Argument dirxzz is only supported on the |
|
|
|
|
| 32Way(H) model. |
|
|
|
|
| This command is always valid without regard |
|
|
|
|
| to the current system state. |
bio | ioxy | [ioxz] | - | - | Use this command to specify the BIO to be |
|
|
|
|
| used on the IOX (PCI Bay) that is attached to |
|
|
|
|
| a partition. |
|
|
|
|
| For partitions with duplicated BIOs, use |
|
|
|
|
| <arg2> to specify the IOX (PCI Bay) with a |
|
|
|
|
| secondary BIO. If <arg2> is omitted, the |
|
|
|
|
| secondary BIO is regarded to be |
|
|
|
|
| |
|
|
|
|
| The IOX (PCI Bay) specified in this |
|
|
|
|
| command must be attached to a partition. |
|
|
|
|
| This command is valid only if the partition is |
|
|
|
|
| inactive. |
|
|
|
|
| It is not supported on the ISPF. |
scsi_sp | pcibx | onoff | - | - | Use this command to specify the SCSI split |
lit |
|
|
|
| mode (split mode ON or OFF) for PCI Bay |
|
|
|
|
| No. x. |
|
|
|
|
| Split mode is set to OFF by default. |
|
|
|
|
| Split mode setting can be changed when the |
|
|
|
|
| partition to which the pertinent PCI Bay |
|
|
|
|
| belongs is inactive or the power to the PCI |
|
|
|
|
| Bay is left off. Split mode setting cannot be |
|
|
|
|
| changed while the partition is booting up or |
|
|
|
|
| shutting down. |
