Base Module

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

cmd

arg1

arg2

arg3

arg4

Description

 

 

clkx

onoff

-

-

Turn On/Off the LED on the CLK Card.

 

 

 

 

 

 

x is a CLK Card number (0-1).

 

 

xbxcx

onoff

-

-

Turn On/Off the LED on the XBX Card.

 

 

 

 

 

 

x is a XBX Card number (0-3).

 

 

cellx

onoff

-

-

Turn On/Off the LED on the CELL Card.

 

 

 

 

 

 

x is a physical CELL number (0-7).

 

 

pcibx

onoff

-

-

Turn On/Off the LED on the PCI Bay.

 

 

 

 

 

 

x is a PCI Bay number (0-7).

 

 

pcix0y

onoff

-

-

Turn On/Off the LEDs on the PCI Bay’s PXH

 

 

 

 

 

 

PCI slots by specifying the slot numbers

 

 

 

 

 

 

printed on the back of the box.

 

 

 

 

 

 

x is a PCI Bay number (0-7).

 

 

 

 

 

 

y is a slot number (PXH slot number (1-8)

 

 

 

 

 

 

printed on the back of the box).

 

 

 

 

 

 

 

 

 

frn

onoff

-

-

Turn On/Off the Fan-Box LEDs by specifying

 

 

 

 

 

 

their locations.

 

 

 

 

 

 

Argument frn specifies the rear-side

 

 

ffn

 

 

 

 

 

 

 

 

Fan-Box, and ffn the front-side Fan-Box.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

loc

-

-

-

-

This command is supported on the 8Way

 

 

 

 

 

 

and ISPF models.

 

 

 

 

 

 

Use this command to manually specify

 

 

 

 

 

 

devices’ location information.

 

 

 

 

 

 

If no argument is specified or an argument

 

 

 

 

 

 

has an error, the loc command help opens.

 

 

 

 

 

 

This command is valid only if all the

 

 

 

 

 

 

partitions are inactive.

 

 

main

d

 

 

This command is supported on the 8Way

 

 

 

 

 

 

and ISPF models.

 

 

 

 

 

 

It sets the vertical position of the main

 

 

 

 

 

 

chassis within the cabinet.

 

 

 

 

 

 

Argument d specifies the position (U) of the

 

 

 

 

 

 

bottom of the main chassis with a decimal

 

 

 

 

 

 

number (0-40).

 

 

 

 

 

 

The default value is null (0).

 

 

pbayx

d

h

-

Set the vertical position and height of Power

 

 

 

 

 

 

Bay No.1 that is installed outside the main

 

 

 

 

 

 

chassis of the 8Way model.

 

 

 

 

 

 

x is only valid if it specifies Power Bay No.1.

 

 

 

 

 

 

Argument d specifies the position (U) of the

 

 

 

 

 

 

bottom of the unit with a decimal number

 

 

 

 

 

 

(0-40).

 

 

 

 

 

 

Argument h specifies the height of the unit

 

 

 

 

 

 

(2).

 

 

 

 

 

 

This command is not supported on the

 

 

 

 

 

 

32Way, ISPF, or Power Bay No. 0 for the

 

 

 

 

 

 

8Way model as the Power Bay position and

 

 

 

 

 

 

height are uniquely determined on those

 

 

 

 

 

 

models.

2-55

855-900549

Page 74
Image 74
NEC 5020M-16, NX7700i operation manual Base Module