Manuals / NEC / Computer Equipment / Server

NEC 5020M-16, NX7700i operation manual Base Module

Models: 5020M-16 NX7700i

1 149

Download 149 pages 48.62 Kb

Page 70

Base Module

cmd	arg1	arg2		arg3	arg4		Description
	pbayx	-	-		-	Enable the Power Bay.
						x is a Power Bay number. The allowable
						value of x is as follows:
						For 32Way:
						0, 1: Power Bay numbers within the Main
							Cabinet
						2, 3: Power Bay numbers within the
							Expansion Cabinet
						For 8Way:
						0:	Power Bay number inside the chassis
						1:	Power Bay number outside the chassis
						For ISPF:
						0:	Power Bay number inside the chassis
	clkx	-	-		-	Enable the CLK.
						x is a CLK number (0 or 1).
						The CLK is installed only in the 32Way
						model.
	xbxcx	[all]	-		-	Enable the XBX Card.
						x is an XBX Card number (0-3).
						If arg2 is omitted, only the XBX Card is
						enabled, with its subcomponents left
						disabled.
						If “all” is specified for arg2, XBX Card is
						enabled including all of its subcomponents.
	xbxxy	[all]	-		-	Enable the XBX LSI.
						x is an XBX Card number (0-3).
						y is an XBX LSI number (0-1) on an XBX
						Card.
						If arg2 is omitted, only the XBX Card is
						enabled, with its subcomponents left
						disabled.
						If “all” is specified for arg2, the XBX Card is
						enabled including all of its subcomponents.

	cellx	[all]	-		-	Enable the CELL Card.
						x is a physical CELL number (0-7).
						If arg2 is omitted, only the CELL Card is
						enabled, with its subcomponents left
						disabled. In this case, console operation will
						be rejected if essential components are
						disabled.
						If “all” is specified for arg2, the CELL Card is
						enabled including all of its subcomponents.
	cnxxy	-	-		-	Enable the CNX LSI.
						x is a physical CELL number (0-7).
						y is a CNX number (0-1) within a CELL.
						CNX1 exists only in the 32Way(H) model.
	procxy	-	-		-	Enable the Processor.
						x is a physical CELL number (0-7).
						y is a Processor number (0-3) within the
						CELL.
	mmxxy	[all]	-		-	Enable the MMX.
						x is a physical CELL number (0-7).
						y is an MMX number (0-3) within the CELL.
						If arg2 is omitted, only the MMX is enabled,
						with its subcomponents left disabled.
						If “all” is specified for arg2, the MMX is
						enabled including all of its subcomponents.

2-51	855-900549

Image 70

NEC 5020M-16, NX7700i operation manual Base Module

Contents

855-900549-A Rev NX7700i/5020M-16 Operation Manual NEC CorporationIn the European Union Disposingused NEC Outside the EuropeanSafety Precautions Do not insert foreign materials into the equipment Handling of the lithium batteryDo not touch the internal components of the equipment Failure processingDisposing/collecting/recycling the equipment Handling of the laser product18kg ATTENTIONMACHINE a FORT COURANT de FUITE CAUTIONUse CopperConductors only ATTENTIONNutilisez que les conducteurs de cuivre 矢印を上に向けて取り付けること。ATTENTIONCouper lalimentation electrique avant de demonter ce capot CAUTIONDisconnect input power before removing this cover注※意：カバーを開ける前に入力電源分電盤切断のこと。注※意：保守時は安定板を引き出すこと。保守者の方へ保守者の方へ警告 WARNING 警告 WARNING243-306629-GRP 243-304367-GRPMARKINGS MARKINGSPreface Rev. 1, MayPreventing Accidental Erasure of Data ContentsCleaning Schedule Life of Data Cartridge Tape for the DAT UnitSystem Startup Digital Audio TapeChapter 1 NX7700i/5020M-16 System Overview Figure. External Views of the Cabinet1.1. Configuration and Specifications of the Base Module NX7700i/5020M-16 System Overview POWER BAYFigure. Layout of Parts in the Base Module I/O MODULETable. Base Module Specifications Main Cabinet Table. Base Module Specifications Cont’dNX7700i/5020M-16 System Overview 545Kg1.2.2. Expanding Memory Capacity 1.2. Expandability1.2.1. Adding Processors 1.2.3. Adding CellsItanium2 Figure. System ConfigurationNX7700i/5020M-16 System Overview Figure. Doors of Cabinet ChapterBase Module Base Module2.1. Partition Function Figure. Image of PartitionsBASE MODULE 2.2. Name and Function of Components 2.2.1. Cabinet Primary CabinetBASE MODULE POWBAY#12.2.4 Cell 2.2.3 Expansion Power Bay2.2.2 Base Module 2.2.5. I/O Module2.2.6. Power Bay Figure. Rear panel of iSP Installed in the Base Module 2.2.7. iSPBase Module 2.2.8.1. Loading and Unloading Media 2.2.8. DVD-ROM UnitFigure. Loading and Unloading DVD-ROM/CD-ROM 2.2.9.2. Notes on Index Labels 2.2.9. DAT Unit2.2.9.1. Location of Index Labels 2.2.9.3. Preventing Accidental Erasure of Data2.2.9.6. Cleaning Medium for the DAT Unit 2.2.9.4. Cleaning the DAT Unit2.2.9.5. Cleaning Schedule 2.2.9.7. Life of Data Cartridge Tape for the DAT Unit2.2.9.10. Loading and Unloading Digital Audio Tapes 2.2.9.9. Notes on the DAT UnitFigure. DAT Units AC SW P1 2.2.10. Notes on Installing the UPSFigure. Jumper Connector for Installing the UPS AC SW AC SWCB1 P3 AC SW2.2.11. System LEDs LED CARD2.3. Consoles 2.3.1. SP ConsoleFigure. Console Connection Diagram Base Module2.4.1.2. Accessible Console Functions 2.4. Service Processor SP2.4.1. Console Connection and Login 2.4.1.1. Type of Console Connections2.4.1.3. Console Status and Login Authentication CM command Serial console inoperative Press ESC Choose Exit iSP login promptLogin password required Password required2.4.1.4. Login and Main Menu iSP BOOT MAIN MENU S iSP commands E Exit The “backup” indicator will not appear if no backup SP existsScreen Example…BOOT FW DescriptionPossible Events including operator entries and System Responses 2.4.2. NoteBase Module 2.4.3. OS BIOS Console CTRL+BPossible Events including operator entries and System Responses DescriptionBase Module 2.4.4. Virtual SOP Virtual System Operator PanelPossible Events including operator entries and System Responses DescriptionBase Module 2.4.4.1. Details of Partition Status Display Base ModuleBase Module 2.4.5. SP Command ConsoleOSBIOS serial console of partition#0 INITIALIZING CTRL+B2.4.5.2. SP Command Prompt 2.4.5.1. SP Command Console Buffer2.4.5.3. SP Message Header System Control 2.4.5.4. SP Command ListThe following tables contain SP command lists by category Base ModuleFigure. System Status Transitions and System Control Commands Settings ConfigurationNormal mode other commands Base Module2.4.6. SP Command Reference Function 2.4.6.1. DF Shut down System Power overrideBase Module Description Base Module2.4.6.2. DN Shut down System Power FunctionFunction 2.4.6.3. DP System DumpDP command was accepted. Dump button interrupt will be generated soon Base ModuleFunction 2.4.6.4. DT SP Data and TimeAlways valid without regard to the current system status Base ModuleISPF does not have two AC power receiving systems 2.4.6.5. EN Environmental Information32Way For one or two AC power receiving systems Always valid without regard to the current system status2-39 Base Modulec d e f The following information will be missing for 8WayBase Module Base Module 2-41tentative Base ModuleThe numbers of PCI Bay cards are changed on 32Way/8Way and ISPF tentativeDescription Base ModuleFunction 2.4.6.6. FV Firmware VersionsAlways valid without regard to the current system status iSPyz--- fv ENTER2.4.6.7. HC Hardware Configuration FunctionBase Module Base Module This command is currently not supported Base ModuleBase Module Base Module arg1Base Module Base Module arg1 This command is currently not supportedBase Module arg2This command is currently not supported Base ModuleBase Module Base Module Description of Status Indicator Strings Base ModuleiSPyz--- hc ENTER Base ModuleHC helpENTER 2-59 Base Moduleb c d e The SM size is shown for the ISPFz “S” if SCSI SPLIT Mode is selected, and “N” if it is deselected Base Module1 LIN=x,y,z x Logical IOX number For 32WayHFor 32WayB Base ModuleFor 8Way For 32WayB, 8Way, or ISPF Base ModuleFor ISPF MMXx2 and MMXx3 are only shown for 32WayBBase Module 2-63TAG0o Base ModuleTAG0e CELL1j j j Base Module2-65 Base Module 2 Listed for the PCI Bay in which the Core Cards are installed3 Listed for the PCI Bay in which the Core Cards are installed For 32Way, subsequently listed to the max. XBX Card numberBase Module 2-67POWBAYs Main cabinet Base ModulePOWBAYs Expansion cabinet Base Module For the 8Way/ISPF model, there are three DPSs in Power BayFor the ISPF, Power Bay1 for dual AC systems is not configured 2-69Description Base ModuleFunction 2.4.6.8. HE HelpAlways valid without regard to the current system status Base ModuleFunction 2.4.6.9. ML Message LogAlways valid without regard to the current system status Base ModuleDescription Base ModuleFunction 2.4.6.10. PC Power CycleiSP0mINFO.2129 partition 0 handed off the control to BIOS pcENTERBase Module 2.4.6.11. RS Cold Reset SystemFunction rsENTERAlways valid without regard to the current system status 2.4.6.12. SG SP/System SettingSetting partition boot method and hot-plug permission FunctionISPF Base ModuleLAN/Serial SP SNMP Configuration SP default FTP Server ConfigurationBase Module sgENTER Base ModuleDescription bENTERENTER Base Module2ENTER onENTERDescription Base ModuleBase Module Description Base ModuleDescription Base ModuleBase Module Manager1 LAN0 IPDescription Base ModuleBase Module 2.4.6.13. SR Save System CMOS/NvRAMFunction file path cmossave/cmos1.bin ENTERDescription DescriptionDescription No Base Module 2.4.6.14. UB Bring up BIOSFunction mm/dd/yyyy HHMMSS 0------- System initialization started. SPFWRxx.xxFunction 2.4.6.15. UP Bring up SystemThis command is valid to inactive partitions DC Off Base ModuleChapter 3 Operation Procedure 3.1. System Startup 3.1.1. System Startup ProcedureSee steps 7 to 11 in next page OS Boot Operation ProcedureSee step 3 in next page Expansion power bay/Base module AC ON StartRemark Operation Procedure 3.1.2. SP Console Messages Operation ProcedureOperation Procedure 2 Example of SP console screen during system startup3.2. System Shutdown 3.2.1. System Shutdown Procedure Operation ProcedureStart Shut down OS See step 1 in next page Turn off console PC Operation ProcedureSee step 6 in next page Turn off AC to expansion power bay/base module See steps 7 and 8 in next page Turn off peripheralsSee 2.2.1 Cabinet for the location of the switch panel. See 2.2.6 Power Bay for the location of the AC switch on the base module and expansion power bay. The number of switches on the switch panel depends on the number of installed base modules and expansion power bays. Take care of the association between these switches and base modules and expansion power bays during switch operation. The switches on the switch panel are used for immediate power shutdown for emergency purposes. When a switch on this panel is turned off, data may be destroyed 1 Example of DC power off display on SP console screen 3.2.2. SP Console MessagesOperation Procedure 3-10Data may be destroyed when the AC switch is turned off during 3.3. Emergency System Shutdown with AC SW3.4. AC-LINK Auto Control Provide criteria for operating the AC switch and use the switch= Enable AC LINK and press Operation Procedure1 SP console screen and operation during AC LINK setup 3-12Use the arrow keys to change settings 3.5. OS Boot3.5.1. OS Boot with Boot Manager Before Installing the OS Use the OS console to operate the EFI Shell. Inputs from theUse the arrow keys to change settings „ Image of the OS Boot screen displayed by the EFI Boot ManagerSLES9 3.5.3. EFI Shell 3.5.4. EFI Shell CommandsEFI Shell Commands Command Operation ProcedureDescription Command Operation ProcedureDescription 3.5.5. OS Boot from EFI Shell fs0¥ cd os Operation ProcedureBoot the OS loader fs0¥os ls3.5.6. EFI Devices Computing UID Example 3.5.7. EFI Boot Option Maintenance Option Boot Maintenance Menu OptionsOperation Procedure Description„ Image of the Boot from a File screen 3.5.7.1. Boot from a FileOperation Procedure ディレクトリを選択して実行プログ 3.5.7.2. Add a Boot Option登録できま 3.5.7.3. Add Boot Options 3.5.7.4. Change Boot Order3.5.7.5. Manage BootNext Setting 3.5.7.6. Set Auto Boot Timeout 3.5.7.7. Setting the Network Boot AcpiPNP0A03,0/Pci30/Mac00004C717743Changing procedure 1 Activate the EFI Boot Manager 3.5.7.8. Changing BIOS Settings EFI System Configuration Menu Processor Configuration 3.6. System Dump Chapter 4 Troubleshooting 4.1. Troubleshootingpressing the SHIFT key on the screen 5.2. DVD-ROM/CD-ROM Chapter 5 Notes on Handling5.1. Transportation 5.3. Digital Audio Tape5.4. Cleaning Figure 5-1 Cleaning Locations5.5. Notes on Installation Notes on Handling Memo