# ftp symbolicname or ipaddress | Q-Logic 64 instruction

D

B – Command Line Interface Config Command

The following is an example of how to create a backup file (configdata) and download the file to the workstation.

SANbox2 #> admin start

SANbox2 (admin) #> config backup

SANbox2 (admin) #> admin end

SANbox2 #> exit

#>ftp symbolic_name or ip_address user: images

password: images ftp> bin

ftp> get configdata ftp> quit

The following is an example of how to upload a configuration backup file (configdata) from the workstation to the switch, and then restore the configuration.

#> ftp symbolic_name or ip_address

user: images

password: images

ftp> bin

ftp> put configdata

ftp> quit

SANbox2 #> admin start

SANbox2 (admin) #> config restore

The switch will be reset after restoring the configuration.

Please confirm (y/n): [n] y

Alarm Msg: [Tue Jun 10 09:25:56.938 2003][A1005.0021][SM][Configuration is being restored - this could take several minutes !]

Alarm Msg: [Tue Jun 10 09:26:19.266 2003][A1000.000A][SM][The switch will be reset in 3 seconds due to a config restore]

SANbox2 (admin) #>

Alarm Msg: [Tue Jun 10 09:26:22.296 2003][A1000.0005][SM][The switch is being reset]

Good bye.

59043-03 A

B-9

Image 131

Q-Logic 64 manual # ftp symbolicname or ipaddress

Contents

SANbox2-64 Fibre Channel Switch Installation Guide Document Revision History SANbox2-64 Fibre Channel Switch Installation Guide Table of Contents Site Requirements Fabric Management Workstation Section InstallationSection Planning Devices Multiple Chassis Fabrics Section Diagnostics/Troubleshooting Appendix a Specifications Section Removal/Replacement Command Syntax Appendix B Command Line Interface Glossary Index Zone Command Zoneset Command 101 Zoning Command 104 Serial Port Pin Identification TablesPage Intended Audience Introduction Related Materials Sicherheitshinweise Safety Notices Federal Communications Commission FCC Class a Statement Communications Statements CE Statement Bsmi Class a Statement Vcci Class a Statement Electrostatic Discharge Sensitivity Esds Precautions Laser Safety Information Zugängliche Teile Accessible PartsPièces Accessibles Preamble General Public License 12.2 Introduction General Public License Introduction General Public License Introduction General Public License No Warranty How to Apply These Terms to Your New Programs Copyright C yyyy name of author Contact Information Technical SupportAvailability Training General Description Chassis Hardware SANbox2-64 64-Port Fibre Channel Switch Slot and Fibre Channel Port Numbering Chassis Controls and LEDs Maintenance Button Placing the Switch in Maintenance Mode Resetting a Switch Fan Fail LED Amber Over Temperature LED AmberChassis LEDs Fibre Channel Ports Input Power LED GreenHeartbeat LED Amber Small Form-Factor Pluggable SFP Transceivers Port Status LED Ethernet Port Port ModesFabric Ports Expansion Port Ethernet Port Serial Port Pin Number Description Serial Port Pin Identification Power Supply Components Power Supply Modules 10. Fans Fans Switch Management Devices Planning Single Switch Fabric with Initiators and Targets Dual Switch Fabric with Initiators and Targets Domain ID, Principal Priority, and Domain ID Lock Multiple Chassis Fabrics Common Topologies Distance Performance Port-to-Port Latency BandwidthLatency Port-to-Port Transmission Combinations Device Access Soft Zones Access Control List Hard Zones Virtual Private Fabric Hard Zones User Account Security Fabric Security Device Security Security Example Switches and HBAs Secret fedcba9876543210fedcba9876543210fedcba Node WWN 100000c0dd07c34d Node WWN 100000c0dd 07e34e Create a security set SecuritySet2 on Switch2 Security Example Host Authentication MS Group Group1 Fabric Management Fabric Services Planning Fabric Management 59043-03 a Management Workstation Requirements Switch Power RequirementsSite Requirements Fabric Management Workstation Environmental Conditions Installing a Switch Avertissement Mount the Switch Rack for service access and ventilation Locked prior to applying power to the switch„ If the switch is mounted in a closed or multi-unit rack Assembly, make sure that the operating temperature inside SANbox2-64 Rail Kit Connect the Switch to AC Power Install SFP Transceivers Avertissement Appendix a Specifications Ethernet and Serial Cable Connections Connect the Management Workstation to the Switch Serial Connection Ethernet Connection Enter the following command at the Solaris prompt Install SANbox Manager SANsurfer Management Suite Disk Linux Installation SANsurfer Management Suite Disk Windows Installation Enter the following command SANsurfer Management Suite Disk Solaris Installation SANbox2 Installation Disk Windows Installation Configure the Switch SANbox2 Installation Disk Linux InstallationSANbox2 Installation Disk Solaris Installation Cable Devices to the Switch Configure the Ports Using SANbox Manager to Install Firmware Install Firmware Enter the following command to install the new firmware Using the CLI to Install FirmwareTo start an admin session, enter the following Close the FTP session Using FTP and the CLI to Install Firmware Powering Down a Switch Normal all pass Post DiagnosticsHeartbeat LED Blink Patterns To recreate the configuration file, do the following Maintenance Mode PatternFatal Error Blink Pattern Configuration File System Error Blink Pattern Ftp Ftp switchname Reset the switch and close the Telnet session Enter the following account name and password userimagesRestore the configuration file Port Status LED Indications Logging Error EPort Isolation Excessive Port Errors Diagnostics/Troubleshooting Post Diagnostics Chassis and Power Supply LEDs Chassis Diagnostics Fan Fail LED is Illuminated Over Temperature LED is IlluminatedInput Power LED Is Extinguished Power Supply Fault LED is Illuminated Output Power LED Is Extinguished Recovering a Switch Maintenance Image Unpack Maintenance Exit Maintenance Remove Switch Config Maintenance Reset Network ConfigMaintenance Reset Password File Maintenance Copy Log Files Maintenance Set Active Image Maintenance Show Firmware Versions Diagnostics/Troubleshooting Recovering a Switch 59043-03 a SFP Transceivers Marginal Operating Configurations Removing the CPU Module CPU Module Removal/Replacement CPU Module Removing the CPU Module Installing the CPU Module Ftp put imagefile Removal/Replacement CPU Module Choose the Replace task Blades Disconnect all cables from the selected I/O blade Choose the slot number 6 for example Removing an I/O Blade To install a new I/O blade, enter y Removal/Replacement I/O Blades CC Blade Slots Cross-Connect Blades Removing a CC Blade Switch Cover Removal Installing a CC Blade Installing a CC Blade Avertissement Removing a Power Supply Module Removing a Power Supply Module Installing a Power Supply Module Removing a Fan Removing a Fan Installing a Fan Installing a Fan Fabric Specifications Maintainability Electrical Dimensions Environmental Regulatory Certifications Shortwave Laser SFP 1G/2G multi-mode Longwave Laser SFP 1G/2G single-mode Page Logging On to a Switch Command Line Interface Table B-1. Command-Line Completion Command Syntax Table B-2. Commands Listed by Authority Level Commands Keywords Admin CommandAuthority Syntax Syntax alias Alias Command Rename aliasold aliasnew Members aliasRemove alias memberlist Edit config Config CommandSyntax config Keywords activate config Save config RestoreArchive function are not compatible with the Config Restore Command # ftp symbolicname or ipaddress Keywords MMDDhhmmCCYY Date CommandSyntax date Fallback Fallback Command Table B-3. Group Member Attributes Group CommandSyntax group Keywords add group Table B-4. Group Member Attributes Copy groupsource groupdestinationCreate group type Edit group member Remove group members Following is an example of the Group Edit commandFollowing is an example of the Group List command Members group Following is an example of the Group Members command Pending firmware and disrupts traffic Hardreset CommandHardreset Authority None Help CommandKeywords command Syntax help command keyword Following is an example of the Help Set Beacon command Authority None Syntax history History Command This command clears the event log and all counters Hotreset CommandHotreset Fabric is in the diagnostic operational state Hotswap Hotswap Command To replace? 1,2,3,4,6,7,8,9 1 Fetch accountname ipaddress filesource filedestination Image CommandCleanup Image Lip Command Accountname Passwd CommandChanges a user account’s password Passwd accountname Keywords ipaddress Ping CommandAuthority None Syntax Ping Ipaddress Displays current system process information Ps CommandFollowing is an example of the Ps command Syntax Examples Syntax quit, exit, or logout Quit CommandCloses the Telnet session Config configname Reset Command Zoning SwitchTable B-5. Switch Configuration Defaults System Mfstov Table B-6. Port Configuration Defaults Table B-8. Zoning Configuration Defaults Table B-7. Alarm Threshold Configuration Defaults Table B-9. Snmp Configuration Defaults Table B-11. Security Configuration Defaults Table B-10. System Configuration Defaults Edit Security CommandKeywords active Clear Save Following is an example of the Security History commandHistory Limits Following is an example of the Security List command Following is an example of the Security Limits command Securityset Command Rename securitysetold securitysetnew Delete securitysetGroups securityset Remove securityset group Syntax set Set Command Pagebreak state Setup optionSwitch state Log option Port portnumber Set Config CommandTable B-12. Set Config Port Parameters Keywords blade slotnumber Send Arbff True instead of IDLEs Table B-12. Set Config Port Parameters Table B-13. Security Configuration Parameters Table B-14. Set Config Switch Parameters Threshold Table B-15. Set Config Threshold Parameters Memory. Refer to FC-SW-2 Compliant Table B-16. Set Config Zoning Parameters Arbff Following is an example of the Set Config Port command Following is an example of the Set Config Switch command Following is and example of the Set Config Security command Following is an example of the Set Config Threshold command This Following is an example of the Set Config Zoning command Component list Set Log CommandSet log Archive Port portlist Level level Level keyword to Info at the same time StartStop Stops logging of events Set Port Command Table B-17. Snmp Configuration Settings Set Setup CommandSnmp configuration and one system configuration Set setup Table B-18. System Configuration Settings SANbox2 admin # set setup snmp Trap1Severity See SANbox2 admin # set setup system Following is an example of the Set Setup System command Blade Show CommandAlarm Keywords about Ns option Fdmi nodewwnLog option Table B-19. Show Port Parameters PagebreakPanel Perf option LIP Alpd Alps Slot slotnumber Post log Users Steering domainidSupport Topology Following is an example of the Show Chassis command Following is an example of the Show Panel command Following is an example of the Show Domains commandFollowing is an example of the Show Fabric command Following is an example of the Show NS local domain command Following is an example of the Show Fdmi commandFollowing is an example of the Show Fdmi WWN command Following is an example of the Show Interface command Following is an example of the Show NS domainID commandFollowing is an example of the Show NS portID command LIPF8F7 Following is an example of the Show Port command Following is an example of the Show Slot command Following is an example of the Show Topology command Following is an example of the Show Switch command Command Line Interface Show Command Following is an example of the Show Version command Blade slotnumber Show Config CommandShow config Following is an example of the Show Config Threshold command Following is an example of the Show Config Switch command Following is an example of the Show Config Zoning command Keywords component Show Log Command Following is an example of the Show Log command Following is an example of the Show Log Options command Show Perf Command Following is an example of the Show Perf Byte command Errors portnumber Mfg Show Setup CommandShow setup Following is an example of the Show Setup Snmp command Following is an example of the Show Setup System command Shutdown Shutdown CommandPower from the switch Status Test CommandTest Port portnumber testtype Test port x internal Command Line Interface Test Command Authority None Syntax uptime Uptime CommandExamples The following is an example of the Uptime command Delete accountname User CommandKeywords accounts Add Following is an example of the User Edit command Following is an example of the User Add command Following is an example of the User List command Following is an example of the User Delete command Whoami Whoami CommandFollowing is an example of the Whoami command Syntax zone Zone Command Type zone zonetype Members zoneRemove zone memberlist Rename zoneold zonenew Following is an example of the Zone Members command Following is an example of the Zone Zonesets command Syntax zoneset Zoneset Command Zones zoneset Following is an example of the Zoneset List commandRemove zoneset zonelist Rename zonesetold zonesetnew Following is an example of the Zoneset Zones command Opens a Zoning Edit session Zoning Command Following is an example of the Zoning Limits command E2JBOD2 Following is an example of the Zoning List command 59043-03 a 107 Command Line Interface Zoning Command 108 59043-03 a Class 2 Service Access Control List ZoneAdministrative State BootP Fabric Management Switch Class 3 ServiceConfigured Zone Sets Default Visibility Maintenance Mode Input Power LEDInter-Switch Link Maintenance Button Principal Switch Output Power LEDOver Temperature LED Power On Self Test Post Zone User Account SecurityVirtual Private Fabric Zone Worldwide Name WWNPage Numerics Index Index-2 59043-03 a 59043-03 a Index-3 Index-4 59043-03 a 59043-03 a Index-5 Index-6 59043-03 a 59043-03 a Index-7