Manuals / Q-Logic / Computer Equipment / Switch

Q-Logic 64 manual Installing a Power Supply Module, Fans

Models: 64

1 244

Download 244 pages 38.52 Kb

Page 112

6 – Removal/Replacement Fans

D

6.5.2

Installing a Power Supply Module

To install a power supply module, do the following:

1.Slide the power supply module into the slot guide until it contacts the backplane.

2.Rotate the blade latch upward to lock the power supply module in place. Fasten the screws.

3.Reconnect the power cord to the power supply module and confirm that the Output Power LED illuminates.

4.Confirm the power supply module status. Do one of the following:

Open a Telnet session and enter the Show Chassis command to display the operational status of the power supply modules. Refer to the ”Show Command” on page B-63.

Observe the power supply status in the Switch data window of the SANbox Manager topology display. Refer to the SANbox2-64 Switch Management User’s Guide.

6.6

Fans

The fans are hot pluggable. This means you can remove or install one of the fans while the switch is operating without disrupting service. The fan is completely enclosed, so there is no risk of injury from the fan blades. The fans are also interchangeable; that is, any fan will fit in any bay. Before removing a fan, connect an ESD wrist strap to a ground point on the chassis or rack.

6-18	59043-03 A

Image 112

Q-Logic 64 manual Installing a Power Supply Module, Fans

Contents

SANbox2-64 Fibre Channel Switch Installation Guide SANbox2-64 Fibre Channel Switch Installation Guide Document Revision HistoryTable of Contents Section Installation Section PlanningDevices Multiple Chassis Fabrics Site Requirements Fabric Management WorkstationSection Diagnostics/Troubleshooting Section Removal/Replacement Appendix a SpecificationsAppendix B Command Line Interface Command SyntaxZone Command Zoneset Command 101 Zoning Command 104 Glossary IndexTables Serial Port Pin IdentificationPage Introduction Intended AudienceRelated Materials Safety Notices SicherheitshinweiseCommunications Statements Federal Communications Commission FCC Class a StatementCE Statement Vcci Class a Statement Bsmi Class a StatementLaser Safety Information Electrostatic Discharge Sensitivity Esds PrecautionsPièces Accessibles Accessible PartsZugängliche Teile General Public License Preamble12.2 Introduction General Public License Introduction General Public License Introduction General Public License How to Apply These Terms to Your New Programs No WarrantyCopyright C yyyy name of author Technical Support AvailabilityTraining Contact InformationGeneral Description SANbox2-64 64-Port Fibre Channel Switch Chassis HardwareSlot and Fibre Channel Port Numbering Maintenance Button Chassis Controls and LEDsResetting a Switch Placing the Switch in Maintenance ModeChassis LEDs Over Temperature LED AmberFan Fail LED Amber Heartbeat LED Amber Input Power LED GreenFibre Channel Ports Port Status LED Small Form-Factor Pluggable SFP TransceiversPort Modes Fabric PortsExpansion Port Ethernet PortSerial Port Ethernet PortSerial Port Pin Identification Pin Number DescriptionPower Supply Modules Power Supply ComponentsFans 10. FansSwitch Management Planning DevicesSingle Switch Fabric with Initiators and Targets Dual Switch Fabric with Initiators and Targets Multiple Chassis Fabrics Domain ID, Principal Priority, and Domain ID LockCommon Topologies Performance DistanceBandwidth LatencyPort-to-Port Transmission Combinations Port-to-Port LatencyDevice Access Access Control List Hard Zones Soft ZonesVirtual Private Fabric Hard Zones Fabric Security User Account SecuritySecurity Example Switches and HBAs Device SecurityNode WWN 100000c0dd07c34d Secret fedcba9876543210fedcba9876543210fedcbaNode WWN 100000c0dd 07e34e Security Example Host Authentication Create a security set SecuritySet2 on Switch2MS Group Group1 Fabric Services Fabric ManagementPlanning Fabric Management 59043-03 a Switch Power Requirements Site RequirementsFabric Management Workstation Management Workstation RequirementsInstalling a Switch Environmental ConditionsMount the Switch AvertissementLocked prior to applying power to the switch „ If the switch is mounted in a closed or multi-unit rackAssembly, make sure that the operating temperature inside Rack for service access and ventilationSANbox2-64 Rail Kit Install SFP Transceivers Connect the Switch to AC PowerAvertissement Appendix a Specifications Connect the Management Workstation to the Switch Ethernet and Serial Cable ConnectionsEthernet Connection Serial ConnectionInstall SANbox Manager Enter the following command at the Solaris promptSANsurfer Management Suite Disk Windows Installation SANsurfer Management Suite Disk Linux InstallationSANsurfer Management Suite Disk Solaris Installation Enter the following commandSANbox2 Installation Disk Windows Installation SANbox2 Installation Disk Solaris Installation SANbox2 Installation Disk Linux InstallationConfigure the Switch Configure the Ports Cable Devices to the SwitchInstall Firmware Using SANbox Manager to Install FirmwareTo start an admin session, enter the following Using the CLI to Install FirmwareEnter the following command to install the new firmware Using FTP and the CLI to Install Firmware Close the FTP sessionPowering Down a Switch Heartbeat LED Blink Patterns Post DiagnosticsNormal all pass Maintenance Mode Pattern Fatal Error Blink PatternConfiguration File System Error Blink Pattern To recreate the configuration file, do the followingFtp Ftp switchname Restore the configuration file Enter the following account name and password userimagesReset the switch and close the Telnet session Logging Error Port Status LED IndicationsEPort Isolation Excessive Port Errors Diagnostics/Troubleshooting Post Diagnostics Chassis Diagnostics Chassis and Power Supply LEDsInput Power LED Is Extinguished Over Temperature LED is IlluminatedFan Fail LED is Illuminated Output Power LED Is Extinguished Power Supply Fault LED is IlluminatedRecovering a Switch Maintenance Exit Maintenance Image UnpackMaintenance Reset Network Config Maintenance Reset Password FileMaintenance Copy Log Files Maintenance Remove Switch ConfigMaintenance Show Firmware Versions Maintenance Set Active ImageDiagnostics/Troubleshooting Recovering a Switch 59043-03 a Marginal Operating Configurations SFP TransceiversCPU Module Removing the CPU ModuleRemoval/Replacement CPU Module Installing the CPU Module Removing the CPU ModuleFtp put imagefile Removal/Replacement CPU Module Blades Choose the Replace taskChoose the slot number 6 for example Disconnect all cables from the selected I/O bladeTo install a new I/O blade, enter y Removing an I/O BladeRemoval/Replacement I/O Blades Cross-Connect Blades CC Blade SlotsRemoving a CC Blade Switch Cover Removal Installing a CC Blade Installing a CC BladeAvertissement Removing a Power Supply Module Removing a Power Supply Module Installing a Power Supply Module Removing a Fan Removing a FanInstalling a Fan Installing a FanFabric Specifications Maintainability Dimensions ElectricalEnvironmental Regulatory Certifications Shortwave Laser SFP 1G/2G multi-mode Longwave Laser SFP 1G/2G single-mode Page Command Line Interface Logging On to a SwitchCommand Syntax Table B-1. Command-Line CompletionCommands Table B-2. Commands Listed by Authority LevelAdmin Command AuthoritySyntax KeywordsAlias Command Syntax aliasRemove alias memberlist Members aliasRename aliasold aliasnew Config Command Syntax configKeywords activate config Edit configRestore Archive function are not compatible with the Config RestoreCommand Save config# ftp symbolicname or ipaddress Syntax date Date CommandKeywords MMDDhhmmCCYY Fallback Command FallbackGroup Command Syntax groupKeywords add group Table B-3. Group Member AttributesCopy groupsource groupdestination Create group typeEdit group member Table B-4. Group Member AttributesFollowing is an example of the Group Edit command Following is an example of the Group List commandMembers group Remove group membersFollowing is an example of the Group Members command Hardreset Hardreset CommandPending firmware and disrupts traffic Help Command Keywords commandSyntax help command keyword Authority NoneFollowing is an example of the Help Set Beacon command History Command Authority None Syntax historyHotreset Command HotresetFabric is in the diagnostic operational state This command clears the event log and all countersHotswap Command HotswapTo replace? 1,2,3,4,6,7,8,9 1 Image Command CleanupImage Fetch accountname ipaddress filesource filedestinationLip Command Passwd Command Changes a user account’s passwordPasswd accountname AccountnamePing Command Authority None Syntax PingIpaddress Keywords ipaddressPs Command Following is an example of the Ps commandSyntax Examples Displays current system process informationCloses the Telnet session Quit CommandSyntax quit, exit, or logout Reset Command Config confignameSwitch Table B-5. Switch Configuration DefaultsSystem ZoningTable B-6. Port Configuration Defaults MfstovTable B-7. Alarm Threshold Configuration Defaults Table B-8. Zoning Configuration DefaultsTable B-9. Snmp Configuration Defaults Table B-10. System Configuration Defaults Table B-11. Security Configuration DefaultsSecurity Command Keywords activeClear EditFollowing is an example of the Security History command HistoryLimits SaveFollowing is an example of the Security Limits command Following is an example of the Security List commandSecurityset Command Delete securityset Groups securitysetRemove securityset group Rename securitysetold securitysetnewSet Command Syntax setSetup option Switch stateLog option Pagebreak stateSet Config Command Table B-12. Set Config Port ParametersKeywords blade slotnumber Port portnumberSend Arbff True instead of IDLEs Table B-12. Set Config Port Parameters Table B-13. Security Configuration Parameters Table B-14. Set Config Switch Parameters Threshold Table B-15. Set Config Threshold Parameters Table B-16. Set Config Zoning Parameters Memory. Refer to FC-SW-2 CompliantFollowing is an example of the Set Config Port command ArbffFollowing is and example of the Set Config Security command Following is an example of the Set Config Switch commandFollowing is an example of the Set Config Threshold command Following is an example of the Set Config Zoning command ThisSet Log Command Set logArchive Component listLevel level Port portlistStart StopStops logging of events Level keyword to Info at the same timeSet Port Command Set Setup Command Snmp configuration and one system configurationSet setup Table B-17. Snmp Configuration SettingsTable B-18. System Configuration Settings SANbox2 admin # set setup snmp Trap1Severity See Following is an example of the Set Setup System command SANbox2 admin # set setup systemShow Command AlarmKeywords about BladeLog option Fdmi nodewwnNs option Pagebreak PanelPerf option Table B-19. Show Port ParametersLIP Alpd Alps Post log Slot slotnumberSteering domainid SupportTopology UsersFollowing is an example of the Show Chassis command Following is an example of the Show Fabric command Following is an example of the Show Domains commandFollowing is an example of the Show Panel command Following is an example of the Show Fdmi WWN command Following is an example of the Show Fdmi commandFollowing is an example of the Show NS local domain command Following is an example of the Show NS portID command Following is an example of the Show NS domainID commandFollowing is an example of the Show Interface command Following is an example of the Show Port command LIPF8F7Following is an example of the Show Slot command Following is an example of the Show Switch command Following is an example of the Show Topology commandCommand Line Interface Show Command Following is an example of the Show Version command Show config Show Config CommandBlade slotnumber Following is an example of the Show Config Switch command Following is an example of the Show Config Threshold commandFollowing is an example of the Show Config Zoning command Show Log Command Keywords componentFollowing is an example of the Show Log Options command Following is an example of the Show Log commandShow Perf Command Errors portnumber Following is an example of the Show Perf Byte commandShow setup Show Setup CommandMfg Following is an example of the Show Setup Snmp command Following is an example of the Show Setup System command Power from the switch Shutdown CommandShutdown Test Command TestPort portnumber testtype StatusTest port x internal Command Line Interface Test Command Examples The following is an example of the Uptime command Uptime CommandAuthority None Syntax uptime User Command Keywords accountsAdd Delete accountnameFollowing is an example of the User Add command Following is an example of the User Edit commandFollowing is an example of the User Delete command Following is an example of the User List commandFollowing is an example of the Whoami command Whoami CommandWhoami Zone Command Syntax zoneMembers zone Remove zone memberlistRename zoneold zonenew Type zone zonetypeFollowing is an example of the Zone Members command Following is an example of the Zone Zonesets command Zoneset Command Syntax zonesetFollowing is an example of the Zoneset List command Remove zoneset zonelistRename zonesetold zonesetnew Zones zonesetFollowing is an example of the Zoneset Zones command Zoning Command Opens a Zoning Edit sessionFollowing is an example of the Zoning Limits command Following is an example of the Zoning List command E2JBOD259043-03 a 107 Command Line Interface Zoning Command 108 59043-03 a Access Control List Zone Administrative StateBootP Class 2 ServiceClass 3 Service Configured Zone SetsDefault Visibility Fabric Management SwitchInput Power LED Inter-Switch LinkMaintenance Button Maintenance ModeOutput Power LED Over Temperature LEDPower On Self Test Post Principal SwitchUser Account Security Virtual Private Fabric ZoneWorldwide Name WWN ZonePage Index NumericsIndex-2 59043-03 a 59043-03 a Index-3 Index-4 59043-03 a 59043-03 a Index-5 Index-6 59043-03 a 59043-03 a Index-7