Figure D-3. System Description | RAD Data comm IPmux-16 specs

Appendix D TFTP Download Procedures	IPmux-16Installation and Operation Manual

Figure D-3. System Description

D-4 Inband TFTP Download Procedure

Image 98

RAD Data comm IPmux-16 operation manual Figure D-3. System Description

Contents

IPmux-16 International Headquarters RAD Data Communications Inc Regulatory Information Safety Warnings Safety Status PortsPage Contents IPmux-16 Troubleshooting and DiagnosticsPacket Delay Variation 30. T1 Physical Layer Configuration Menu List of Tables Applications OverviewVersions IPmux-16 with an E1 interface Site C Site aSite B Ethernet FeaturesManagement Internal Cross Connect Mode of OperationMultibundling QoS General Physical DescriptionStandards Internal Clock Rear Panel Functional DescriptionFront Panel Single E1/T1 Port at Central Site Timing Modes TestingOperation Modes External Network Timing E1/T1 Device ConfigurationIPmux-16 Configuration Single Source Clock Network IPmux-16 in Adaptive Timing Mode Frame Format Layer Data LayerLayer IP Layer Ethernet Frame Structure UDP Support Packet Delay VariationVlan Support UDP Source Port as Destination Voice Port Pdvt Jitter Buffer Pdvt Buffer Effect on DelayTo configure jitter buffer depth Intrinsic PDV Frame Overhead Packets Throughput Ethernet ThroughputEthernet Throughput Unframed E1 Length Ethernet Throughput Unframed T1 Round Trip DelayWhere n = TDM bytes/frame T1 interface = System Usage for TDM Bytes per Frame End-to-End Alarm GenerationThroughput Limitations and CAC T1 Modules Technical SpecificationsE1 Modules Green On when main power supply is OFF when malfunction is Connector DB-9System Indicators General Power is off Power Physical Introduction Site Requirements and Prerequisites Package Contents Equipment Needed DB-9 Female Signal Name Pin No Null Cable Pinout Connections Connecting Interfaces and Cables Installation and SetupSetting Jumpers Grounding Connecting the Alarm Connector Location of ConnectorsConnecting the Control Port To connect the Control Port To connect the power Connecting the PowerAlarm Connector Pinout Pin No Signal Name Status Front Panel Controls, Connectors, and Indicators IPmux-16 Front Panel LEDs Operating Instructions IPmux-16 System Indicators and SwitchesTo power up IPmux-16 without a terminal Turning IPmux-16 On Without Control Terminal Turning IPmux-16 On With Control Terminal User Name and PasswordTo power up IPmux-16 with a control terminal To enter as a superuser To power off the unit To set all passwords to the default valueIf a user forgets his password Getting Started Menu Operations Navigating IPmux-16 Terminal Menu Tree Main Menu Configuring System ParametersTo access the System menu Viewing System Information General Information To display IPmux-16 general information Type 3 Event Log in the System Menu Event LogTo view the IPmux-16 event log Ping Configuring IPmux-16To access the Configuration menu To ping To display the General Configuration Menu General ConfigurationManagement Configuration Bundle connections Community Authentication/CommunityManagement Configuration To configure the Host IP To set the Authentication/Community parametersHost Configuration To change the Host ID configuration Host IP is deleted Configure the new Host IPManager List Manager List Type 4 Default Gateway in the Management Configuration menu Default GatewayTo configure the default gateway To set the manager list parameters To activate/deactivate a trap generation for an alarm Alarms Trap MaskTo define the Alarms Traps Mask IPmux-16 Alarms To configure the Ascii terminal Ascii Terminal ConfigurationAll other Alarms are unused If no characters were sent by the terminal for Software Download/Upload Time/Date UpdateTime/Date Update Menu To perform Software Download/Upload Modem To download/upload the code/configurationType 2 to download/upload via Tftp To download or upload a file by X-Modem, do the following To download or upload a file by TFTP, do the following XXXXXXXXX.YYY View Transfer Status 23. View Transfer Status Window Type 6 File System in the General Configuration menu Set Default ParametersTo set the default parameters File System CDB CFG LOG COD To configure the IPmux-16 physical layer Physical Layer ConfigurationLAN Configuration To view and configure LAN port type E1/T1 Configuration To configure the E1/T1 interfaces E1 Physical Layer Configuration E1/T1 Physical Layer Configuration To change the Line Type setting To change the Loopback State settingTo change the RX Sensitivity setting To change the source of the transmit clock Type 7 Cond. data pattern and enter a new value To determine the Signaling mode CAS enable / CAS disableRange 00-FF Default Value FF T1 Physical Layer Configuration Internal Local clock source used Default value Adaptive To change the Channel Code setting To change the Channel Type settingDefault value T1-ESF To change the Channel Mode setting To change the Restore Time setting Type a Cond. data pattern and enter a new value Time Slots Configuration To configure the time slots Active Time Slots in this Bundle To configure IPmux-16 bundlesSET To set the source DS0 Bundle ID Bundle Connection ConfigurationTo view and configure Bundle Connection parameters To set the Connection Status To define a destination bundle at the remote IPmux-16 Internal Cross Connect SettingsTo define a Next Hop To define the Jitter Buffer Vlan Tagging Setting Vlan and IP SupportSystem Usage ToS configuration configures the Whole byte Viewing Configuration SummaryTo set the IP ToS Type of Service IP ToS Type 3 Performance Monitoring in the Main menu Monitoring System PerformanceTo view performance statistics To view E1/T1 or Ethernet statistics LOS Compliance to standardsPhysical Port Statistics LCV E1/T1 Alarms and Statistics Alarm Failure Comments Alarms and Statistics Febe Alarm Failure Comments Valid in X only SES LAN Statistics 37. LAN Statistics Menu Description Bundle Connection StatusTo view Connection status IP Channel Status Bundle Connection Status Operation Configuring IPmux-16 Front Panel LEDs Error DetectionWorking with the Alarm Buffer Event Types Event Description Corrective Action Fault Probable Cause Remedial Action TroubleshootingIPmux-16 Troubleshooting Chart Internal Loop Diagnostic TestsExternal Loop To run a loopback test T1 FDL Support T1 PRM Support Troubleshooting and Diagnostics Diagnostic Tests General Booting IPmux-16Boot Sequence General Figure A-1 Boot Screen Accessing the File System IPMUX-16 Boot Menu Appendix a Boot Sequence for Downloading Software Snmp Operations Snmp EnvironmentSnmp Principles Management Information Base MIB MIB Structure MIBs Supported by the IPmux-16 Snmp Agent Management Domains Under Snmp Network Management Stations AuthenticationSnmp Communities To open a Telnet application Using Telnet to Manage the IPmux-16Starting a Telnet Session Telnet Operation Configuration windowConfigurations, menu line 4 15 Minute Timeout System Security To start download Inband Tftp Download ProcedureNew software Log in as Superuser su Preliminary ProcedureBefore performing Tftp download Checking the Download To check the download Figure D-3. System Description DC Power Supply Connection CBL-DC-3WL/F Connecting the DC Plug