E1/T1 Configuration | RAD Data comm IPmux-16 specification

IPmux-16Installation and Operation Manual	Chapter 3 Operation

Note If Auto Negotiation is set to Enable and there is some incompatibility in the

Auto Negotiation process, Ipmux-16 automatically changes to half-duplex mode. To overcome this situation, set Auto Negotiation to Disable and set Default type to the desired mode.

➤To define the maximum capabilities of the module for the auto-negotiation process (can be lower then the actual capabilities):

•Type 2.

Use the <Spacebar> on your keyboard to toggle between the parameters: 10BaseT Half Duplex, 10BaseT Full Duplex, 100BaseT Half Duplex, 100BaseT Full Duplex.

➤To set the default parameters:

1.Type 3.

2.Use the <Spacebar> on your keyboard to toggle between the module mode (half/full duplex) and Rate (10mbps/100Mbps).

Note This parameter is valid only when the auto-negotiation mode is disabled (RFC 2239).

Main Menu

↓

2.Configuration

↓

2.Physical Layer

Configuration

↓

3 or 4. E1/T1 Physical Layer Configuration

E1/T1 Configuration

➤To configure the E1/T1 interfaces:

•Type 3 or 4 (according to slot containing E1/T1 module) (E1/T1 Configuration) in the Physical Layer Configuration menu.

Configuring IPmux-16

3-25

Image 57

RAD Data comm IPmux-16 operation manual E1/T1 Configuration, To configure the E1/T1 interfaces

Contents

International Headquarters RAD Data Communications Inc IPmux-16 Regulatory Information Safety Status Ports Safety WarningsPage Contents Troubleshooting and Diagnostics Packet Delay VariationIPmux-16 30. T1 Physical Layer Configuration Menu List of Tables Versions OverviewApplications IPmux-16 with an E1 interface Site a Site BSite C Features ManagementEthernet Multibundling Mode of OperationInternal Cross Connect QoS Standards Physical DescriptionGeneral Internal Clock Front Panel Functional DescriptionRear Panel Single E1/T1 Port at Central Site Testing Operation ModesTiming Modes IPmux-16 Configuration E1/T1 Device ConfigurationExternal Network Timing Single Source Clock Network Frame Format IPmux-16 in Adaptive Timing Mode Layer IP Layer LayerLayer Data Ethernet Frame Structure Vlan Support Packet Delay VariationUDP Support UDP Source Port as Destination Voice Port To configure jitter buffer depth Pdvt Buffer Effect on DelayPdvt Jitter Buffer Intrinsic PDV Ethernet Throughput Unframed E1 Ethernet ThroughputFrame Overhead Packets Throughput Length Where n = TDM bytes/frame Round Trip DelayEthernet Throughput Unframed T1 T1 interface = End-to-End Alarm Generation Throughput Limitations and CACSystem Usage for TDM Bytes per Frame Technical Specifications E1 ModulesT1 Modules System Indicators General Connector DB-9Green On when main power supply is OFF when malfunction is Power is off Power Physical Site Requirements and Prerequisites Introduction Equipment Needed Package Contents Null Cable Pinout Connections DB-9 Female Signal Name Pin No Setting Jumpers Installation and SetupConnecting Interfaces and Cables Grounding Connecting the Control Port Location of ConnectorsConnecting the Alarm Connector To connect the Control Port Alarm Connector Pinout Connecting the PowerTo connect the power Pin No Signal Name Status IPmux-16 Front Panel LEDs Front Panel Controls, Connectors, and Indicators To power up IPmux-16 without a terminal IPmux-16 System Indicators and SwitchesOperating Instructions Turning IPmux-16 On Without Control Terminal To power up IPmux-16 with a control terminal User Name and PasswordTurning IPmux-16 On With Control Terminal To enter as a superuser If a user forgets his password To set all passwords to the default valueTo power off the unit Getting Started Navigating Menu Operations IPmux-16 Terminal Menu Tree To access the System menu Configuring System ParametersMain Menu Viewing System Information To display IPmux-16 general information General Information Event Log To view the IPmux-16 event logType 3 Event Log in the System Menu To access the Configuration menu Configuring IPmux-16Ping To ping Management Configuration General ConfigurationTo display the General Configuration Menu Bundle connections Authentication/Community Management ConfigurationCommunity Host Configuration To set the Authentication/Community parametersTo configure the Host IP To change the Host ID configuration Manager List Configure the new Host IPHost IP is deleted Manager List To configure the default gateway Default GatewayType 4 Default Gateway in the Management Configuration menu To set the manager list parameters To define the Alarms Traps Mask Alarms Trap MaskTo activate/deactivate a trap generation for an alarm IPmux-16 Alarms All other Alarms are unused Ascii Terminal ConfigurationTo configure the Ascii terminal If no characters were sent by the terminal for Time/Date Update Menu Time/Date UpdateSoftware Download/Upload To perform Software Download/Upload Type 2 to download/upload via Tftp To download/upload the code/configurationModem To download or upload a file by X-Modem, do the following XXXXXXXXX.YYY To download or upload a file by TFTP, do the following 23. View Transfer Status Window View Transfer Status To set the default parameters Set Default ParametersType 6 File System in the General Configuration menu File System CDB CFG LOG COD LAN Configuration Physical Layer ConfigurationTo configure the IPmux-16 physical layer To view and configure LAN port type To configure the E1/T1 interfaces E1/T1 Configuration E1/T1 Physical Layer Configuration E1 Physical Layer Configuration To change the RX Sensitivity setting To change the Loopback State settingTo change the Line Type setting To change the source of the transmit clock To determine the Signaling mode CAS enable / CAS disable Range 00-FF Default Value FFType 7 Cond. data pattern and enter a new value Internal Local clock source used Default value Adaptive T1 Physical Layer Configuration Default value T1-ESF To change the Channel Type settingTo change the Channel Code setting To change the Channel Mode setting Type a Cond. data pattern and enter a new value To change the Restore Time setting To configure the time slots Time Slots Configuration To configure IPmux-16 bundles SETActive Time Slots in this Bundle To view and configure Bundle Connection parameters Bundle Connection ConfigurationTo set the source DS0 Bundle ID To set the Connection Status To define a Next Hop Internal Cross Connect SettingsTo define a destination bundle at the remote IPmux-16 To define the Jitter Buffer Setting Vlan and IP Support System UsageVlan Tagging To set the IP ToS Type of Service Viewing Configuration SummaryToS configuration configures the Whole byte IP ToS To view performance statistics Monitoring System PerformanceType 3 Performance Monitoring in the Main menu To view E1/T1 or Ethernet statistics Physical Port Statistics Compliance to standardsLOS LCV Alarm Failure Comments E1/T1 Alarms and Statistics Febe Alarms and Statistics SES Alarm Failure Comments Valid in X only 37. LAN Statistics Menu LAN Statistics Bundle Connection Status To view Connection statusDescription Bundle Connection Status IP Channel Status Operation Configuring IPmux-16 Error Detection Working with the Alarm BufferFront Panel LEDs Event Description Corrective Action Event Types Troubleshooting IPmux-16 Troubleshooting ChartFault Probable Cause Remedial Action External Loop Diagnostic TestsInternal Loop To run a loopback test T1 PRM Support T1 FDL Support Troubleshooting and Diagnostics Diagnostic Tests Boot Sequence Booting IPmux-16General General Figure A-1 Boot Screen IPMUX-16 Boot Menu Accessing the File System Appendix a Boot Sequence for Downloading Software Snmp Environment Snmp PrinciplesSnmp Operations MIB Structure Management Information Base MIB Management Domains Under Snmp MIBs Supported by the IPmux-16 Snmp Agent Authentication Snmp CommunitiesNetwork Management Stations Using Telnet to Manage the IPmux-16 Starting a Telnet SessionTo open a Telnet application Configurations, menu line 4 15 Minute Timeout Configuration windowTelnet Operation System Security Inband Tftp Download Procedure New softwareTo start download Preliminary Procedure Before performing Tftp downloadLog in as Superuser su To check the download Checking the Download Figure D-3. System Description Connecting the DC Plug DC Power Supply Connection CBL-DC-3WL/F