RAD Data comm IPmux-16 - page 47

IPmux-16 Installation and Operation Manual Chapter 3 Operation

Configuring IPmux-16 3-15

➤ To set the manager list parameters:

1. Enter 1 to set the manager IP address: range of 0.0.0.0. to 255.255.255.255.

2. Enter 3 to set the alarm trap: On or Off. Use the Spacebar to toggle between

these two settings. When set to On, the alarm trap informs the manager of the

occurrence of any alarm enabled in the Alarms Trap Mask screen. It informs

the manager of both entry and exit from an alarm state. When OFF, no alarm

trap will be sent regardless of the Mask defined in the Alarm Trap Mask screen.

3. Enter 4 to set the system trap: On or Off. Use the Spacebar to toggle between

these two settings. When set to On, the system trap informs the manager

whenever there is a change in the system power-supply status, heat alarm.

4. To ping the manager, press P.

5. To access additional manager-list parameters, press N to go to the next

manager-list window.

Default Gateway

Main menu

↓

2. Configuration

↓

1. General

Configuration

↓

3. Management

Configuration

↓

4. Default

Gateway

Default gateway defines the gateway to which management frames will be sent

(when the manager is not in the host subnet). When a next hop is not defined in

the connection parameters, the default gateway is used.

➤ To configure the default gateway

1. Type 4 (Default Gateway) in the Management Configuration menu.

DEFAULT GATEWAY

1. Gateway IP 0.0.0.0

ESC. Exit

Select item from the menu.

Figure 3-16. Default Gateway Menu

2. Type 1 and then type in the IP address of the default gateway.

Contents

Main IPmux-16 TDMoIP Gateway Installation and Operation Manual Notice Warranty Limitation of Warranty Exclusive Remedies Regulatory Information FCC-15 User Information Safety Warnings Telecommunication Safety Page Contents List of Figures Page List of Tables Chapter 1 Introduction 1.1 Overview Versions Applications Chapter 1 Introduction IPmux-16 Installation and Operation Manual Figure 1-2. IP Based Metropolitan Area Network Features Management T1 E1 IP Mode of Operation Multibundling Internal Cross Connect QoS Timing 1.2 Physical Description Front Panel Rear Panel 1.3 Functional Description Operation Modes Unframed Fractional Fractional with CAS Testing External Network Timing Single Source Clock Network Frame Format Page VLAN Support UDP Support Packet Delay Variation PDVT (Jitter) Buffer Intrinsic PDV ebytes/framTDM configured (n=1 8). PDVT Buffer Effect on Delay Ethernet Throughput ebytes/framTDM Round Trip Delay n 48 ebytes/fram TDM End-to-End Alarm Generation Throughput Limitations and CAC 1.4 Technical Specifications E1 Modules E1 Port E1 Framing Ethernet Modules General Chapter 2 Installation 2.1 Introduction Caution 2.2 Site Requirements and Prerequisites Warning 2.3 Package Contents Power Cable 2.4 Equipment Needed Table 2-1. Null Cable Pinout Connections Figure 2-1. Null Cable (CBL-DB-9/DB-9/NULL) Pin Shorts 2.5 Installation and Setup Setting Jumpers Connecting Interfaces and Cables Grounding Fuses Location of Connectors Connecting the Control Port Connecting the Alarm Connector Connecting the Power Chapter 3 Operation 3.1 Introduction 3.2 Front Panel Controls, Connectors, and Indicators 3.3 Operating Instructions Turning IPmux-16 On Without Control Terminal Turning IPmux-16 On With Control Terminal User Name and Password Turning IPmux-16 Off 3.4 Getting Started Page Chapter 3 Operation IPmux-16 Installation and Operation Manual Figure 3-3. IPmux-16 Terminal Menu Tree 3-6 Menu Operations Main Menu 3.6 Configuring System Parameters Viewing System Information Figure 3-5. System Menu General Information Figure 3-6. General Information Window Event Log Type 3 (Event Log) in the System Menu. Figure 3-8. Logfile Events Sample Menu Ping 3.7 Configuring IPmux-16 General Configuration Management Configuration Page Page Manager List Page Alarms Trap Mask ASCII Terminal Configuration Time/Date Update Software Download/Upload Page Page Page Set Default Parameters File System Page Physical Layer Configuration LAN Configuration E1/T1 Configuration Figure 3-29. E1 Physical Layer Configuration Menu Page Page Page Page Page Time Slots Configuration Page Bundle Connection Configuration Internal Cross Connect Settings Note System Usage Setting VLAN and IP Support VLAN Tagging IP ToS Viewing Configuration Summary Monitoring System Performance Compliance to standards: T1: ANSI T1.403, AT&T TR62411, G.703, G.704, G.804 Page Table 3-3. Alarms and Statistics (Cont.) Page LAN Statistics Figure 3-37. LAN Statistics Menu Table 3-4. LAN Statistics Slot/Channel: Select the LAN module and channel on which you want to view statistics Bundle Connection Status To view Connection status: Page Page Chapter 4 Troubleshooting and Diagnostics 4.1 Error Detection Front Panel LEDs Working with the Alarm Buffer Table 4-1. Event Types 4.2 Troubleshooting 4.3 Diagnostic Tests External Loop Internal Loop T1 FDL Support T1 PRM Support Page Appendix A Boot Sequence for Downloading Software A.1 General A.2 Booting IPmux-16 General Boot Sequence Page Accessing the File System Page Appendix B SNMP Management B.1 SNMP Environment SNMP Principles SNMP Operations Management Information Base (MIB) MIB Structure MIBs Supported by the IPmux-16 SNMP Agent Management Domains Under SNMP SNMP Communities Authentication Network Management Stations Appendix C Telnet C.1 General C.2 Using Telnet to Manage the IPmux-16 Starting a Telnet Session Telnet Operation System Security Appendix D TFTP Download Procedures D.1 Inband TFTP Download Procedure General Preliminary Procedure Checking the Download Page DC Power Supply Connection CBL-DC-3WL/F Note: Ignore this supplement if the unit is AC-powered. Connecting the DC Plug