T1 FDL Support, T1 PRM Support | RAD Data comm IPmux-16 specs

IPmux-16Installation and Operation Manual	Chapter 4 Troubleshooting and Diagnostics

	AIS	IPmux-16


PBX
PBX
	Internal Loop

Figure 4-2. Internal Loop

T1 FDL Support

The following FDL commands are supported:

•Line Loopback (LLB): external loop

•Line Loopback Release: normal state

T1 PRM Support

The T1 module supports PRM message transmission according to the ANSI T1.403 protocol. Messages are transmitted every second.

Diagnostic Tests

4-5

Page 83

Image 83

RAD Data comm IPmux-16 operation manual T1 FDL Support, T1 PRM Support

Contents

International Headquarters RAD Data Communications Inc IPmux-16 Regulatory Information Safety Status Ports Safety WarningsPage Contents IPmux-16 Troubleshooting and DiagnosticsPacket Delay Variation 30. T1 Physical Layer Configuration Menu List of Tables IPmux-16 with an E1 interface OverviewVersions Applications Site C Site aSite B Ethernet FeaturesManagement QoS Mode of OperationMultibundling Internal Cross Connect Internal Clock Physical DescriptionStandards General Single E1/T1 Port at Central Site Functional DescriptionFront Panel Rear Panel Timing Modes TestingOperation Modes Single Source Clock Network E1/T1 Device ConfigurationIPmux-16 Configuration External Network Timing Frame Format IPmux-16 in Adaptive Timing Mode Ethernet Frame Structure LayerLayer IP Layer Layer Data UDP Source Port as Destination Voice Port Packet Delay VariationVlan Support UDP Support Intrinsic PDV Pdvt Buffer Effect on DelayTo configure jitter buffer depth Pdvt Jitter Buffer Length Ethernet ThroughputEthernet Throughput Unframed E1 Frame Overhead Packets Throughput T1 interface = Round Trip DelayWhere n = TDM bytes/frame Ethernet Throughput Unframed T1 System Usage for TDM Bytes per Frame End-to-End Alarm GenerationThroughput Limitations and CAC T1 Modules Technical SpecificationsE1 Modules Power is off Connector DB-9System Indicators General Green On when main power supply is OFF when malfunction is Power Physical Site Requirements and Prerequisites Introduction Equipment Needed Package Contents Null Cable Pinout Connections DB-9 Female Signal Name Pin No Grounding Installation and SetupSetting Jumpers Connecting Interfaces and Cables To connect the Control Port Location of ConnectorsConnecting the Control Port Connecting the Alarm Connector Pin No Signal Name Status Connecting the PowerAlarm Connector Pinout To connect the power IPmux-16 Front Panel LEDs Front Panel Controls, Connectors, and Indicators Turning IPmux-16 On Without Control Terminal IPmux-16 System Indicators and SwitchesTo power up IPmux-16 without a terminal Operating Instructions To enter as a superuser User Name and PasswordTo power up IPmux-16 with a control terminal Turning IPmux-16 On With Control Terminal Getting Started To set all passwords to the default valueIf a user forgets his password To power off the unit Navigating Menu Operations IPmux-16 Terminal Menu Tree Viewing System Information Configuring System ParametersTo access the System menu Main Menu To display IPmux-16 general information General Information Type 3 Event Log in the System Menu Event LogTo view the IPmux-16 event log To ping Configuring IPmux-16To access the Configuration menu Ping Bundle connections General ConfigurationManagement Configuration To display the General Configuration Menu Community Authentication/CommunityManagement Configuration To change the Host ID configuration To set the Authentication/Community parametersHost Configuration To configure the Host IP Manager List Configure the new Host IPManager List Host IP is deleted To set the manager list parameters Default GatewayTo configure the default gateway Type 4 Default Gateway in the Management Configuration menu IPmux-16 Alarms Alarms Trap MaskTo define the Alarms Traps Mask To activate/deactivate a trap generation for an alarm If no characters were sent by the terminal for Ascii Terminal ConfigurationAll other Alarms are unused To configure the Ascii terminal To perform Software Download/Upload Time/Date UpdateTime/Date Update Menu Software Download/Upload To download or upload a file by X-Modem, do the following To download/upload the code/configurationType 2 to download/upload via Tftp Modem XXXXXXXXX.YYY To download or upload a file by TFTP, do the following 23. View Transfer Status Window View Transfer Status File System Set Default ParametersTo set the default parameters Type 6 File System in the General Configuration menu CDB CFG LOG COD To view and configure LAN port type Physical Layer ConfigurationLAN Configuration To configure the IPmux-16 physical layer To configure the E1/T1 interfaces E1/T1 Configuration E1/T1 Physical Layer Configuration E1 Physical Layer Configuration To change the source of the transmit clock To change the Loopback State settingTo change the RX Sensitivity setting To change the Line Type setting Type 7 Cond. data pattern and enter a new value To determine the Signaling mode CAS enable / CAS disableRange 00-FF Default Value FF Internal Local clock source used Default value Adaptive T1 Physical Layer Configuration To change the Channel Mode setting To change the Channel Type settingDefault value T1-ESF To change the Channel Code setting Type a Cond. data pattern and enter a new value To change the Restore Time setting To configure the time slots Time Slots Configuration Active Time Slots in this Bundle To configure IPmux-16 bundlesSET To set the Connection Status Bundle Connection ConfigurationTo view and configure Bundle Connection parameters To set the source DS0 Bundle ID To define the Jitter Buffer Internal Cross Connect SettingsTo define a Next Hop To define a destination bundle at the remote IPmux-16 Vlan Tagging Setting Vlan and IP SupportSystem Usage IP ToS Viewing Configuration SummaryTo set the IP ToS Type of Service ToS configuration configures the Whole byte To view E1/T1 or Ethernet statistics Monitoring System PerformanceTo view performance statistics Type 3 Performance Monitoring in the Main menu LCV Compliance to standardsPhysical Port Statistics LOS Alarm Failure Comments E1/T1 Alarms and Statistics Febe Alarms and Statistics SES Alarm Failure Comments Valid in X only 37. LAN Statistics Menu LAN Statistics Description Bundle Connection StatusTo view Connection status Bundle Connection Status IP Channel Status Operation Configuring IPmux-16 Front Panel LEDs Error DetectionWorking with the Alarm Buffer Event Description Corrective Action Event Types Fault Probable Cause Remedial Action TroubleshootingIPmux-16 Troubleshooting Chart To run a loopback test Diagnostic TestsExternal Loop Internal Loop T1 PRM Support T1 FDL Support Troubleshooting and Diagnostics Diagnostic Tests General Booting IPmux-16Boot Sequence General Figure A-1 Boot Screen IPMUX-16 Boot Menu Accessing the File System Appendix a Boot Sequence for Downloading Software Snmp Operations Snmp EnvironmentSnmp Principles MIB Structure Management Information Base MIB Management Domains Under Snmp MIBs Supported by the IPmux-16 Snmp Agent Network Management Stations AuthenticationSnmp Communities To open a Telnet application Using Telnet to Manage the IPmux-16Starting a Telnet Session System Security Configuration windowConfigurations, menu line 4 15 Minute Timeout Telnet Operation To start download Inband Tftp Download ProcedureNew software Log in as Superuser su Preliminary ProcedureBefore performing Tftp download To check the download Checking the Download Figure D-3. System Description Connecting the DC Plug DC Power Supply Connection CBL-DC-3WL/F