Menu Operations, Navigating | RAD Data comm IPmux-16 specification

IPmux-16Installation and Operation Manual		Chapter 3 Operation

3.5 Menu Operations

Navigating

Navigate the IPmux-16 terminal menus to set and view configuration parameters. Figure 3-3maps the IPmux-16 terminal menus. Use this tree as a reference aid while performing configuration and control functions.

Menu Operations

3-5

Page 37

Image 37

RAD Data comm IPmux-16 operation manual Menu Operations, Navigating

Contents

International Headquarters RAD Data Communications Inc IPmux-16 Regulatory Information Safety Status Ports Safety WarningsPage Contents Packet Delay Variation Troubleshooting and DiagnosticsIPmux-16 30. T1 Physical Layer Configuration Menu List of Tables Versions OverviewApplications IPmux-16 with an E1 interface Site B Site aSite C Management FeaturesEthernet Multibundling Mode of OperationInternal Cross Connect QoS Standards Physical DescriptionGeneral Internal Clock Front Panel Functional DescriptionRear Panel Single E1/T1 Port at Central Site Operation Modes TestingTiming Modes IPmux-16 Configuration E1/T1 Device ConfigurationExternal Network Timing Single Source Clock Network Frame Format IPmux-16 in Adaptive Timing Mode Layer IP Layer LayerLayer Data Ethernet Frame Structure Vlan Support Packet Delay VariationUDP Support UDP Source Port as Destination Voice Port To configure jitter buffer depth Pdvt Buffer Effect on DelayPdvt Jitter Buffer Intrinsic PDV Ethernet Throughput Unframed E1 Ethernet ThroughputFrame Overhead Packets Throughput Length Where n = TDM bytes/frame Round Trip DelayEthernet Throughput Unframed T1 T1 interface = Throughput Limitations and CAC End-to-End Alarm GenerationSystem Usage for TDM Bytes per Frame E1 Modules Technical SpecificationsT1 Modules System Indicators General Connector DB-9Green On when main power supply is OFF when malfunction is Power is off Power Physical Site Requirements and Prerequisites Introduction Equipment Needed Package Contents Null Cable Pinout Connections DB-9 Female Signal Name Pin No Setting Jumpers Installation and SetupConnecting Interfaces and Cables Grounding Connecting the Control Port Location of ConnectorsConnecting the Alarm Connector To connect the Control Port Alarm Connector Pinout Connecting the PowerTo connect the power Pin No Signal Name Status IPmux-16 Front Panel LEDs Front Panel Controls, Connectors, and Indicators To power up IPmux-16 without a terminal IPmux-16 System Indicators and SwitchesOperating Instructions Turning IPmux-16 On Without Control Terminal To power up IPmux-16 with a control terminal User Name and PasswordTurning IPmux-16 On With Control Terminal To enter as a superuser If a user forgets his password To set all passwords to the default valueTo power off the unit Getting Started Navigating Menu Operations IPmux-16 Terminal Menu Tree To access the System menu Configuring System ParametersMain Menu Viewing System Information To display IPmux-16 general information General Information To view the IPmux-16 event log Event LogType 3 Event Log in the System Menu To access the Configuration menu Configuring IPmux-16Ping To ping Management Configuration General ConfigurationTo display the General Configuration Menu Bundle connections Management Configuration Authentication/CommunityCommunity Host Configuration To set the Authentication/Community parametersTo configure the Host IP To change the Host ID configuration Manager List Configure the new Host IPHost IP is deleted Manager List To configure the default gateway Default GatewayType 4 Default Gateway in the Management Configuration menu To set the manager list parameters To define the Alarms Traps Mask Alarms Trap MaskTo activate/deactivate a trap generation for an alarm IPmux-16 Alarms All other Alarms are unused Ascii Terminal ConfigurationTo configure the Ascii terminal If no characters were sent by the terminal for Time/Date Update Menu Time/Date UpdateSoftware Download/Upload To perform Software Download/Upload Type 2 to download/upload via Tftp To download/upload the code/configurationModem To download or upload a file by X-Modem, do the following XXXXXXXXX.YYY To download or upload a file by TFTP, do the following 23. View Transfer Status Window View Transfer Status To set the default parameters Set Default ParametersType 6 File System in the General Configuration menu File System CDB CFG LOG COD LAN Configuration Physical Layer ConfigurationTo configure the IPmux-16 physical layer To view and configure LAN port type To configure the E1/T1 interfaces E1/T1 Configuration E1/T1 Physical Layer Configuration E1 Physical Layer Configuration To change the RX Sensitivity setting To change the Loopback State settingTo change the Line Type setting To change the source of the transmit clock Range 00-FF Default Value FF To determine the Signaling mode CAS enable / CAS disableType 7 Cond. data pattern and enter a new value Internal Local clock source used Default value Adaptive T1 Physical Layer Configuration Default value T1-ESF To change the Channel Type settingTo change the Channel Code setting To change the Channel Mode setting Type a Cond. data pattern and enter a new value To change the Restore Time setting To configure the time slots Time Slots Configuration SET To configure IPmux-16 bundlesActive Time Slots in this Bundle To view and configure Bundle Connection parameters Bundle Connection ConfigurationTo set the source DS0 Bundle ID To set the Connection Status To define a Next Hop Internal Cross Connect SettingsTo define a destination bundle at the remote IPmux-16 To define the Jitter Buffer System Usage Setting Vlan and IP SupportVlan Tagging To set the IP ToS Type of Service Viewing Configuration SummaryToS configuration configures the Whole byte IP ToS To view performance statistics Monitoring System PerformanceType 3 Performance Monitoring in the Main menu To view E1/T1 or Ethernet statistics Physical Port Statistics Compliance to standardsLOS LCV Alarm Failure Comments E1/T1 Alarms and Statistics Febe Alarms and Statistics SES Alarm Failure Comments Valid in X only 37. LAN Statistics Menu LAN Statistics To view Connection status Bundle Connection StatusDescription Bundle Connection Status IP Channel Status Operation Configuring IPmux-16 Working with the Alarm Buffer Error DetectionFront Panel LEDs Event Description Corrective Action Event Types IPmux-16 Troubleshooting Chart TroubleshootingFault Probable Cause Remedial Action External Loop Diagnostic TestsInternal Loop To run a loopback test T1 PRM Support T1 FDL Support Troubleshooting and Diagnostics Diagnostic Tests Boot Sequence Booting IPmux-16General General Figure A-1 Boot Screen IPMUX-16 Boot Menu Accessing the File System Appendix a Boot Sequence for Downloading Software Snmp Principles Snmp EnvironmentSnmp Operations MIB Structure Management Information Base MIB Management Domains Under Snmp MIBs Supported by the IPmux-16 Snmp Agent Snmp Communities AuthenticationNetwork Management Stations Starting a Telnet Session Using Telnet to Manage the IPmux-16To open a Telnet application Configurations, menu line 4 15 Minute Timeout Configuration windowTelnet Operation System Security New software Inband Tftp Download ProcedureTo start download Before performing Tftp download Preliminary ProcedureLog in as Superuser su To check the download Checking the Download Figure D-3. System Description Connecting the DC Plug DC Power Supply Connection CBL-DC-3WL/F