RAD Data comm IPmux-16 - page 72

Chapter 3 Operation IPmux-16 Installation and Operation Manual

3-40 Configuring IPmux-16

Table 3-3. E1/T1 Alarms and Statistics

Alarm Failure Comments

LOS Loss of Signal Sync LED Off.

• For T1: A second during which 192 contiguous pulse positions have no

pulse of either positive or negative polarity (signal is more than 30 dB

below nominal amplitude.

• For E1: A second during which 255 contiguous pulse positions have no

pulse of either positive or negative polarity.

LOF Loss of Frame Sync LED off.

• For E1/T1: A second during which an OOF (see below) e rror persists for

2.5 seconds and no AIS error (see below) is detected.

LCV Line Code

Violation

• Line Code Violation

For T1: A second during which BPV (Bipolar Violation) or EXZ errors have

occurred.

• For E1: A second during which two cons ecutive BPVs of the same

polarity are received.

• BPV is the occurrence of a pulse with the same polarity as the previous

pulse.

• EXZ is the occurrence of a zero string greater than 15 for AMI or 7 for

B8ZS.

• Complies with ITU-TI.431, 0.161, G.775 and G.821 standards.

Rcv RAI

(Yellow

Alarm)

Remote

Alarm

Indication

The Sync LED flashes.

• For E1/T1, a second during which an RAI pattern is recei ved from the far

end when the far-end framer enters a RED state (Loss of Frame).

AIS Alarm

Indication

Signal–

Received

from User

The Sync LED is off.

• For T1: A second during which an unframed “all 1” s ignal is received for

3 milliseconds.

• For E1: A second during which a string of 512 bits contains fewer than

three zero (0) bits.

Contents

Main IPmux-16 TDMoIP Gateway Installation and Operation Manual Notice Warranty Limitation of Warranty Exclusive Remedies Regulatory Information FCC-15 User Information Safety Warnings Telecommunication Safety Page Contents List of Figures Page List of Tables Chapter 1 Introduction 1.1 Overview Versions Applications Chapter 1 Introduction IPmux-16 Installation and Operation Manual Figure 1-2. IP Based Metropolitan Area Network Features Management T1 E1 IP Mode of Operation Multibundling Internal Cross Connect QoS Timing 1.2 Physical Description Front Panel Rear Panel 1.3 Functional Description Operation Modes Unframed Fractional Fractional with CAS Testing External Network Timing Single Source Clock Network Frame Format Page VLAN Support UDP Support Packet Delay Variation PDVT (Jitter) Buffer Intrinsic PDV ebytes/framTDM configured (n=1 8). PDVT Buffer Effect on Delay Ethernet Throughput ebytes/framTDM Round Trip Delay n 48 ebytes/fram TDM End-to-End Alarm Generation Throughput Limitations and CAC 1.4 Technical Specifications E1 Modules E1 Port E1 Framing Ethernet Modules General Chapter 2 Installation 2.1 Introduction Caution 2.2 Site Requirements and Prerequisites Warning 2.3 Package Contents Power Cable 2.4 Equipment Needed Table 2-1. Null Cable Pinout Connections Figure 2-1. Null Cable (CBL-DB-9/DB-9/NULL) Pin Shorts 2.5 Installation and Setup Setting Jumpers Connecting Interfaces and Cables Grounding Fuses Location of Connectors Connecting the Control Port Connecting the Alarm Connector Connecting the Power Chapter 3 Operation 3.1 Introduction 3.2 Front Panel Controls, Connectors, and Indicators 3.3 Operating Instructions Turning IPmux-16 On Without Control Terminal Turning IPmux-16 On With Control Terminal User Name and Password Turning IPmux-16 Off 3.4 Getting Started Page Chapter 3 Operation IPmux-16 Installation and Operation Manual Figure 3-3. IPmux-16 Terminal Menu Tree 3-6 Menu Operations Main Menu 3.6 Configuring System Parameters Viewing System Information Figure 3-5. System Menu General Information Figure 3-6. General Information Window Event Log Type 3 (Event Log) in the System Menu. Figure 3-8. Logfile Events Sample Menu Ping 3.7 Configuring IPmux-16 General Configuration Management Configuration Page Page Manager List Page Alarms Trap Mask ASCII Terminal Configuration Time/Date Update Software Download/Upload Page Page Page Set Default Parameters File System Page Physical Layer Configuration LAN Configuration E1/T1 Configuration Figure 3-29. E1 Physical Layer Configuration Menu Page Page Page Page Page Time Slots Configuration Page Bundle Connection Configuration Internal Cross Connect Settings Note System Usage Setting VLAN and IP Support VLAN Tagging IP ToS Viewing Configuration Summary Monitoring System Performance Compliance to standards: T1: ANSI T1.403, AT&T TR62411, G.703, G.704, G.804 Page Table 3-3. Alarms and Statistics (Cont.) Page LAN Statistics Figure 3-37. LAN Statistics Menu Table 3-4. LAN Statistics Slot/Channel: Select the LAN module and channel on which you want to view statistics Bundle Connection Status To view Connection status: Page Page Chapter 4 Troubleshooting and Diagnostics 4.1 Error Detection Front Panel LEDs Working with the Alarm Buffer Table 4-1. Event Types 4.2 Troubleshooting 4.3 Diagnostic Tests External Loop Internal Loop T1 FDL Support T1 PRM Support Page Appendix A Boot Sequence for Downloading Software A.1 General A.2 Booting IPmux-16 General Boot Sequence Page Accessing the File System Page Appendix B SNMP Management B.1 SNMP Environment SNMP Principles SNMP Operations Management Information Base (MIB) MIB Structure MIBs Supported by the IPmux-16 SNMP Agent Management Domains Under SNMP SNMP Communities Authentication Network Management Stations Appendix C Telnet C.1 General C.2 Using Telnet to Manage the IPmux-16 Starting a Telnet Session Telnet Operation System Security Appendix D TFTP Download Procedures D.1 Inband TFTP Download Procedure General Preliminary Procedure Checking the Download Page DC Power Supply Connection CBL-DC-3WL/F Note: Ignore this supplement if the unit is AC-powered. Connecting the DC Plug