Toshiba 351C, 451C, 281C manual CCA0, CCB0, CCD0, CCE0, CCF0, CDE0

Error code	Classification	Contents	Troubleshooting
CC71	Finisher related	Punch ROM checksum error: Abnormality of check-	P. 5-79
	service call	sum value on Hole punch controller PC board is
		detected when the power is turned on. [MJ-1101
		(when MJ-6101 is installed)]
CC72		Punch RAM read/write error: Abnormality of check-	P. 5-79
		sum value on Hole punch controller PC board is
		detected when the power is turned on. [MJ-1101
		(when MJ-6101 is installed)]
CC80		Front alignment motor abnormality: Front alignment	P. 5-80
		motor is not rotating or front aligning plate is not
		moving normally. [MJ-1022]
		Front aligning plate motor abnormality: Front align-
		ing plate motor is not rotating or aligning plate is not
		moving normally. [MJ-1023/1024]
		Rear alignment motor abnormality: The rear align-	P. 5-80
		ment motor is not rotating or the rear alignment
		plate is not moving normally. [MJ-1101]
CC90		Upper stack tray lift motor abnormality: The upper	P. 5-81
		stack tray lift motor is not rotating or the upper stack
		tray is not moving normally. [MJ-1022]
CCA0		Lower stack tray lift motor abnormality: The lower	P. 5-82
		stack tray lift motor is not rotating or the lower stack
		tray is not moving normally. [MJ-1022]
CCB0		Rear jogging motor abnormality: The rear jogging	P. 5-82
		motor is not rotating or the rear jogging plate is not
		moving normally. [MJ-1022]
CCD0		Stack ejection motor abnormality: Stack ejection	P. 5-83
		motor or stack ejection roller is not rotating nor-
		mally. [MJ-1023/1024]
CCE0		Paper trailing edge assist motor abnormality: Paper	P. 5-83
		trailing edge assist motor is not rotating or paper
		trailing edge assist is not moving normally. [MJ-
		1023/1024]
CCF0		Gear changing motor abnormality: Gear changing	P. 5-83
		motor is not rotating normally. [MJ-1023/1024]
CDE0		Paddle motor abnormality: The paddle motor is not	P. 5-84
		rotating or the paddle is not rotating normally. [MJ-
		1101]
CE00		Communication error between finisher and punch	P. 5-84
		unit: Communication error between finisher control-
		ler PC board and punch controller PC board [MJ-
		1023/1024 (when MJ-6004 is installed)]
		[MJ-1101 (when MJ-6101 is installed)]
CE10	Image control related	Image quality sensor abnormality (OFF level): The	P. 5-85
	service call	output value of this sensor is out of a specified
		range when sensor light source is OFF.
CE20		Image quality sensor abnormality (no pattern level):	P. 5-86
		The output value of this sensor is out of a specified
		range when the image quality control test pattern is
		not formed.
CE40		Image quality control test pattern abnormality: The	P. 5-87
		test pattern is not formed normally.
CE50		Temperature/humidity sensor abnormality: The out-	P. 5-88
		put value of this sensor is out of a specified range.
CE90		Drum thermistor abnormality: The output value of	P. 5-88
		the drum thermistor is out of a specified range.

© June 2005 TOSHIBA TEC	e-STUDIO281c/351c/451c ERROR CODE AND SELF-DIAGNOSTIC MODE
	2 - 11

2

06/08