Error code

Classification

Contents

 

Troubleshooting

EA80

Finisher jam

Stapling jam: Stapling is not performed properly.

 

P. 5-43

 

(Saddle stitcher sec-

[MJ-1024]

 

 

 

tion)

 

 

 

EA90

Door open jam: The delivery cover or inlet cover

 

P. 5-43

 

 

has opened dur-ing printing [MJ-1024].

 

 

EAA0

 

Power-ON jam: Paper exists at No.1 paper sensor,

 

P. 5-44

 

 

No. 2 paper sensor, No.3 paper sensor, vertical

 

 

 

 

path paper sensor or delivery sensor when power is

 

 

 

 

turned ON. [MJ-1024]

 

 

EAB0

 

Transport stop jam: The paper which passed

 

P. 5-44

 

 

through the inlet sensor does not reach or pass

 

 

 

 

No.1 paper sensor, No. 2 paper sensor, No.3 paper

 

 

 

 

sensor or delivery sensor. [MJ-1024]

 

 

EAC0

 

Transport delay jam: The paper which has reached

 

P. 5-45

 

 

the inlet sensor does not pass through the inlet sen-

 

 

 

 

sor. [MJ-1024]

 

 

EAD0

Other paper jam

Print end command time-out jam: The printing has

 

P. 5-47

 

 

not finished normally because of the communica-

 

 

 

 

tion error between the SYS board and LGC board

 

 

 

 

at the end of printing.

 

 

EAE0

Finisher jam

Receiving time time-out jam: The printing has been

 

P. 5-47

 

 

interrupted because of the communication error

 

 

 

 

between the equipment and finisher when the

 

 

 

 

paper is transported from the equipment to the fin-

 

 

 

 

isher.

 

 

EAF0

Finisher jam

Stack return jam: It cannot load the paper which

 

P. 5-42

 

(Finisher section)

passed through the delivery roller on the intermedi-

 

 

 

 

ary process tray. [MJ-1022]

 

 

EB30

Finisher jam

Ready time time-out jam: The equipment judges

 

P. 5-47

 

 

that the paper transport to the finisher is disabled

 

 

 

 

because of the communication error between the

 

 

 

 

equipment and finisher at the start of printing.

 

 

EB50

Paper transport jam

Paper remaining on the transport path: The multiple

 

P. 5-16

 

 

feeding of preceding paper caused the misfeeding

 

 

 

 

of upcoming paper.

 

 

EB60

 

Paper remaining on the transport path: The multiple

 

P. 5-17

 

 

feeding of preceding paper caused the misfeeding

 

 

 

 

of upcoming paper (redetection after no jam is

 

 

 

 

detected at [EB50]).

 

 

ED10

Finisher jam

Sideways adjustment motor (M2) home position

 

P. 5-48

 

 

detection error: The Sideways adjustment motor is

 

 

 

 

not at the home position. [MJ-1101 (when MJ-6101

 

 

 

 

is installed)]

 

 

ED11

 

Skew adjustment motor (M1) home position detec-

 

P. 5-48

 

 

tion abnormality: The Skew adjustment motor is not

 

 

 

 

at the home position. [MJ-1101 (when MJ-6101 is

 

 

 

 

installed)]

 

 

ED12

 

Shutter home position error: The shutter is not at

 

P. 5-49

 

 

the home position. [MJ-1101]

 

 

ED13

 

Front alignment plate home position error: The front

 

P. 5-49

 

 

alignment plate is not at the home position. [MJ-

 

 

 

 

1101]

 

 

ED14

 

Rear alignment plate home position error: The rear

 

P. 5-50

 

 

alignment plate is not at the home position. [MJ-

 

 

 

 

1101]

 

 

ED15

 

Paddle home position error: The paddle is not at the

 

P. 5-50

 

 

home position. [MJ-1101]

 

 

ED16

 

Buffer tray home position error: The buffer tray is

 

P. 5-51

 

 

not at the home position. [MJ-1101]

 

 

e-STUDIO281c/351c/451c ERROR CODE AND SELF-DIAGNOSTIC MODE

© June 2005 TOSHIBA TEC

 

 

2 - 6

 

 

06/08

Page 6
Image 6
Toshiba 451C, 281C, 351C manual EAA0, EAB0, EAC0, EAD0, EAE0, EAF0